Wafer
thin crystalline material sliced from ingot.
See Also: Wafer Thickness, Wafer Failure Analysis, Wafer Edge, Wafer Resistivity, Wafer Mapping, Wafer Probes, Wafer Probers, Wafer Inspection, Probe Cards
-
Product
Automated Front & Backside Mask Aligner System
Model 6000
-
With over 4 decades of manufacturing in the semiconductor industry, OAI meets the growing challenge of a dynamic market with an elite class of production photolithography equipment. Built on the proven OAI modular platform, the Model 6000 has front and backside alignment that is fully automated with a submicron printing capability as well as submicron top to bottom front side alignment accuracy which delivers performance that is unmatched at any price. Choose either topside or optional backside alignment which uses OAI’s customized advanced recognition pattern software. These Mask Aligners have OAI’s Advanced Beam Optics with better than ±3% uniformity and a throughput of 200 wafers per hour in first mask mode, which results in higher yields. The Series 6000 can handle a wide variety of wafers from thick and bonded substrates (up to 7000 microns), warped wafers (up to 7 mm-10mm), thin substrates (down to 100 micron thick), and thick photo resist.
-
Product
Test Head Manipulators
Cobal 250
-
The Cobal 250 offers the best-in-class range of motion for universal manipulators with seven degrees of motion. Separate linear movements make it easier for the operator to dock, undock, and redock the test head in seconds. In combination with inTEST EMS docking, the Cobal 250 is compatible with testers for both Wafer Sort and Final Test, minimizing the time and cost when moving a tester between Sort and Final Test.
-
Product
Particle Deposition Systems
-
MSP’s 2300G3 Particle Deposition System sets the standards for wafer inspection and metrology equipment. This advanced tool is vital for increasing the yield of future leading-edge devices, while meeting the measurement needs of today.
-
Product
Integrated Couplers/ Harmonic Mixers
-
These waveguide bandwidth integrated coupler/mixers are designed to allow phase locking or signal monitoring of compact millimeter wave systems. RF inputs and outputs are on opposite sides of a thin wafer to obtain minimum insertion length. These devices use silicon Schottky barrier beam-lead diodes on a rugged stripline circuit. Nominal coupling value is 10 dB. For coupling values greater than 10 dB, non-directional coupler models are available (consult factory).
-
Product
PROBE CARD
-
the electrical characteristics of the individual CHIPs in WAFER that have been completed through the FAB stage during the semiconductor fabrication process
-
Product
Saw Mark Tester
SRT-301
-
SRT-301 Saw Mark Tester is used to Measure Line-mark depth of the wafer surface,it has the advantages such. As easy carried, Conveniently operated Liquid crystal display, energy conservation and so on, At the same time,it has the built-in printer and rechargeable batteries , All design are up to the standards of JIS,DIN,ISO,ANSI.
-
Product
Vacuum Probing Systems
-
Built using our PS4L patented technology, SemiProbe manufactures a family of Vacuum Probing Systems, which test wafers or substrates in a vacuum environment. Additionally, individual die and broken/partial wafers can be tested with the Vacuum Probing System. All key modules are interchangeable and upgradeable.
-
Product
CD-SEM
-
Our CD-SEM tools measure the width, height, sidewall angle, etc. of wiring patterns on semiconductor photomasks and wafers.
-
Product
Hydrofluoric Acid Monitor
CM-200A/210A
-
The CM-200A/210A hydrofluoric acid monitors have been developed specifically to meet the stringent demands of semiconductor manufacturing. The CM-200A/210A provides a real time read-out of hydrofluoric acid concentration by measuring the electric conductivity of the sample solution. These superior units offer high repeatability even at low concentrations. The CM-200A/210A can be used for a variety of purposes ranging from monitoring etched wafer cleaning processes to any other industrial application of hydrofluoric acid.
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Humidity Sensors
-
digital humidity sensor with integrated temperature sensor that provides excellent measurement accuracy at very low power. The device measures humidity based on a novel capacitive sensor. The humidity and temperature sensors are factory calibrated. The innovative WLCSP (Wafer Level Chip Scale Package) simplifies board design with the use of an ultra-compact package. The sensing element of the HDC1008 is placed on the bottom part of the device, which makes the HDC1008 more robust against dirt, dust, and other environmental contaminants. The HDC1008 is functional within the full 40C to +125C temperature range.
-
Product
CMP Tester
CP-6
-
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
Product
Probe Card
T90™ Series
-
The 90 mm tile was designed for mounting on a standard 4.5″ probe card holder for multi-site wafer level reliability testing. The 1.6 mm (0.062″) thick rails allow the chassis to slip into planarity adjustable probe card holders for most analytical probe stations.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
Product
Wafer Edge Profile Measurement
WATOM
-
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Product
Hi-Speed Discrete Test System
QT-6000
-
QT-6000 Test System, with built-in capacitance test (DC+CAP) and Scanbox etc, is applicable to devices like medium & small power transistors, MOS-FET, diodes and Wafer.
-
Product
Semiconductor Technology, Micro Scriber
Precision Micro Diamond Scriber MR200
-
Optik Elektronik Gerätetechnik GmbH
Precision micro diamond scriber MR 200 for exact manual scribing for defined cutting of structured silicon wafers.
-
Product
Warpage Metrology System
TableTop Shadow Moiré (TTSM)
-
Measure warpage of substrates up to 300mm x 310 mm (a 300mm wafer or two JEDEC trays) with the entire measurement taking less than two seconds. Whether individual parts or a JEDEC tray of multiple parts, the TTSM provides an ultra-fast and highly accurate measurement at room temperature that is suited for tabletop use.
-
Product
Probe Card
VC20E Series
-
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
Product
Tabletop Mask Aligner
Model 200
-
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
Product
Probe Needles for Wafer Sort and Test Applications
-
Advanced Probing Systems, Inc.
APS is the global leader in the manufacture of probe needles used in cantilevered probe cards. All probe needles used in wafer sort are manufactured according to customer specifications using stringent in-process quality assurance procedures.
-
Product
Probe Station
S-1160
-
S-1160 Probe Station 100mm, 150mm and 200mm wafer stage's completely manual and user friendly.
-
Product
Ultra-Low Frequency Workstation
MK52 Series
-
Providing Ultra-Low Frequency levels, the MK52 Series offers the ultimate low natural frequency performance for a wide range of high resolution instruments, such as analytical balances, cell injection, confocal microscopes, patch clamping, optical microscopes, wafer probing, sensor calibration, atomic force microscopes and other sensitive equipment requiring high isolation efficiency.
-
Product
Equipment Front End Module Wafer Handler
Sigma EFEM
-
Integration transforms the bond tester into a fully automated system. We offer various types of EFEM (Equipment Front End Module) wafer handlers, to combine with a Sigma W12 for operator-free bond testing.
-
Product
Micro-spot DUV Spectroscopic Reflectometry
FilmTek 2000 PAR
-
Scientific Computing International
A low-cost solution for high-throughput, fully-automated mapping of patterned wafers for development and production environments. Utilizes patented parabolic mirror technology to measure wavelengths from DUV to NIR with a spot size as small as 13µm. Fully user-customizable wafer mapping capabilities rapidly generate 2D and 3D data maps of any measured parameter.
-
Product
High Throughput 1 ns Pulsed IV Memory Test Solution
NX5730A
-
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
Product
Mask Flatness Measurement System
Tropel® UltraFlatTM 200 Mask System
-
The Tropel® UltraFlatTM 200 Mask System was designed specifically for the photomask industry. It delivers the lowest measurement uncertainty for ever-tightening mask flatness specifications. Shrinking device features require not only flatter wafers, but flatter masks.
-
Product
Surface & Volume Low Resistivity Meter for Conductive Materials
Loresta GP
-
The Loresta GX Meter is an intelligent, multi purpose low resistivity meter equipped with software that calculates resistivity correction factors. A variety of 4 pin probes are available for use with the Loresta GX. The instrument is typically used in Product Engineering, R&D, and Quality Control. Applications include measurement of conductive paint, conductive plastics, conductive rubber, conductive film, silicon wafers, antistatic materials, EMI shield materials, conductive fiber, conductive ceramics, etc.
-
Product
Probe Card
VC43™/VC43EAF™
-
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
Product
Firmware Engineering Projects
-
Precision Development Consulting Inc
Hand control module for teleprompter, Analog data acquisition and filtering, High-Power Arc Lamp Power Supply Controller and RTP gas flow and Vacuum System controller, Disk drive company test racks, Disk Drive Spindle Motor Tester, Disk Drive Head Stack Tester, Wafer photoresist coating and development system control PC boards, Nuclear Plant secondary water temperature monitor
