Memory Test Systems
-
Product
AC Hysteresis Graph Test System
DX-2012SA
-
Under continuous frequency of 1 kHz to 500 kHz, automatic measurement of magnetic hysteresis loop of the soft magnetic materials such as silicon steel, precision alloy, non-crystal and ferrite, accurate measurement on the dynamic magnetic characteristic parameters such as amplitude permeability µa, loss angle d, loss iron Pc, remanence Br and coercivity Hc.
-
Product
200 Vdc External Voltage Bias Fixture
16065A
Test Fixture
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
GSP-2B Test System Interface Probe
GSP-2B
ICT/FCT Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 125Recommended Travel (mm): 3.18Overall Length (mil): 845Overall Length (mm): 21.46
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
Power device test system
-
This system is suitable for DC testing of IGBT, IGBT module (1in1～7in1). Built-in hi-current switching relay circuit inside test head, it is capable ofDC testing from device itself to module. Highly accurate repeatability testing is available by high speed rise time which is suppressed its heat in hi-current
-
Product
Battery Test Systems
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10
-
Product
Ultra-high Performance Solution for Memory Device Test
Magnum EPIC
-
Teradyne’s Magnum EPIC is a high-performance test solution for latest generation DRAM devices. These devices are key enablers for technologies like 5G, AI, cloud computing, autonomous vehicles, AR/VR and applications with high definition graphics.
-
Product
Partial Discharge Testing Of Transformer & Localization System
AE-150™
-
The is designed to detect and localize Partial Discharge activity by correlating acoustic and electric sensors' data. The AE-150™ has many acquisition modes, each used for detecting and locating Partial Discharge activity in a transformer. The AE-150™ unit is mounted on the transformer tank using its powerful magnets that also hold four acoustic sensors.
-
Product
Engine Performance/Endurance Test System
-
Various types of test system as follows can be built up in combination with measurement control equipment and peripheral instruments (fuel flow meters, actuators, temperature control device, combustion analysis system, ECU monitor, OBD, sound and vibration measurement instruments, emission analyzer, smoke meter etc.)·Traveling fuel economy test·Gas emission test·Output performance test·Deterioration/endurance test·Combustion analysis·Sound source probing
-
Product
Chloride Test System
C-CL-2000
-
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
Product
Partial Discharge Test System
TPP
-
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
Product
Air Data Test Set System
B511
-
The BRAT Option B511 is an option to the BRAT Test System utilizing Commercial-Off-The-Shelf (COTS) equipment. The system is used to augment the existing BRAT capabilities to test rate of change of altitude or pressure.
-
Product
Battery Cycle Test Systems
-
Chroma Systems Solutions, Inc.
High precision, integrated battery charge / discharge cycle test systems designed for lithium ion and other chemistries and applications including EV batteries and energy storage systems. Chroma’s battery test equipment provides advanced features including regenerative discharge systems that recycles energy from the battery back into the channels in the system or to the grid. Systems are configurable and flexible with multiple channel capabilities that can be upgraded as testing requirements change.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
ATE & Test Systems
-
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
Product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
-
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
Product
Test Automation System for Heavy-Duty Engine Emission Testing
STARS HDEET
-
STARS HDEET is a Heavy-Duty Engine Emission Test application available as an optional extension to STARS Automation. It provides efficient test cycle execution, emissions equipment control, results calculation and reporting, in compliance with the different legislative standards. Its flexible design offers a wide range of customization while addressing the various requirements for research and development, conformity of production, and certification testing.
-
Product
Electro-Stimulation Equipment Testing System
STIMU-600
-
Test device for functional testing of electrical stimulation devices.
-
Product
RSP-2T Test System Interface Probe
RSP-2T
ICT/FCT Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 167Full Travel (mm): 4.24Recommended Travel (mil): 79Recommended Travel (mm): 2.00
-
Product
Memory Burn-in Tester
B6700 Series
-
B6700 can test as many as 48 burn-in boards in parallel at speeds up to 10 MHz, which helps memory suppliers get their newest products to market faster while also reducing testing costs. An original high performance chamber improves yield by assuring high temperature accuracy while generating high temperature. It also shortens the temperature rise and fall time which leads to shortening the test time.
-
Product
Resistivity Test System
RMS-1000
-
Accurate and powerful performance. - Possible to get much accurate resistivity value by taking 8 raw data. - Good to check ohmic contact by flowing forward and reverse current.2. We provide various sample mounting board and probe head and tips.3. We have an optional item which can measure in variable temperature. - Room Temperature ~ 300dC.
-
-
Product
Memory Diagnostic Utility
MemTest86
-
MemTest86 is the original, free, stand alone memory testing software for x86 computers. MemTest86 boots from a USB flash drive or CD and tests the RAM in your computer for faults using a series of comprehensive algorithms and test patterns.
-
Product
Boundary Scan / JTAG Test Development System
onTAP Development
-
The onTAP Development system will speed up your project development time and keep costs under control. These tools enable you to quickly and easily develop, run, and debug JTAG tests ranging from single JTAG chain applications to multiple JTAG chain applications with multi-die modules, merged sub-assemblies, and multi-drop configurations.
-
Product
Ionic Contamination Test Systems
CM+ Series
-
The Contaminometer (CM+ Series) system was originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s. Historically, International Standard IPC-J-STD001 stated that assemblies be cleaned to a value of <1.5µg/cm2 of NaCl equivalence. However, the new design is linked to the introduction of the new process control metric introduced by Gen3 Systems: Process Ionic Contamination Testing. The CM+ Series measure the amount of ionic contamination in accordance with all existing test methods, often referred to as ROSE testing, as well as the new PICT test.
-
Product
Automated Testing Systems
-
Instron’s automated testing systems bring precision, productivity, and safety to materials testing by automating routine tensile, flexural, and compression operations. Available as full turnkey platforms or modular add-ons for existing test frames, these systems — including the AT3 three-axis, AT6 six-axis robotic, AT2 automated XY stages, CT6 cobot integration, and carousel stations — allow labs to boost throughput, reduce operator variability, and free up staff for higher-value activities. The systems are engineered to support a wide spectrum of materials (plastics, metals, films, composites, medical devices) and comply with international ASTM and ISO test standards while enhancing repeatability and workflow efficiency.
-
Product
Cellular Base Station Factory Test Systems
-
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
Product
Mechanical Shock Test System
BW-MST-E5000
-
The Mechanical Shock Tower develops the kinetic energy electromagnetically. An iron core "bullet" is attracted to the magnetic core of the solenoid by the dense magnetic field that is created as current flows through the field coil of the shock tower. As the bullet is drawn into the center of the magnetic field the acceleration increases exponentially as the gap reduces to zero on impact causing the high impact shock
