Dry Blocks
-
product
Dry Dielectric RF Coaxial Loads
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
product
Dry Bulb Temperature Probe for WBGT
TP3207.2
Dry bulb temperature probe used for calculating the following indices: IREQ,WCI, DLE, RT, PMV, PPD, WBGT, SR and mean radiant temperature. Pt100 sensor.
-
product
DC Blocks
The Keysight DC blocks offer a new level of DC blocking with performance specified from 50 kHz all the way up to 67 GHz. Precision coaxial connector interfaces ensure an excellent impedance match across wide bandwidths, and come in a variety of RF connectors to fit your application needs. Two choices of DC Voltage ratings make these suitable for a wide range of applications.
-
-
product
160-Pin DIN41612 Connector Block, Female
92-965-160-F
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
25-Pin D-Type Male Connector Block
92-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Block Downconverter
RQ028
Teledyne Defence & Space (TDS) down converters are designed to convert digitised, band limited RF signal down to a lower frequency signal. These modules are used to reduce input signal which allows lower speed processors to better process fast incoming signals. A wideband mmW block downconverter suitable for extending the operational bandwidth of other devices into this range. With LO signals at 32GHz and 44GHz, two operational bands are available. Other frequency plans with and without pre-selection can be offered on request.
-
product
25-Pin D-Type Male Connector Block
40-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Dry Dielectric RF Coaxial Loads
4000 Series
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
product
DC Blocking Power Splitter Combiner
PD5112
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
MPI Test Blocks
Is used in magnetic particle inspection will help you maintain your magnetic particle process by verifying magnetic particle performance.
-
product
D,C. Block
WDCB-6SI
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Benchtop Electric Blast Drying Oven
Guangdong Test EQ Equipment co., Ltd.
- Precision & Uniformity: Multi-zone airflow design ensures ±2% temperature uniformity (per ASTM E1459). Auto-reversing fan eliminates hot/cold spots.- Rapid Drying: Turbo blast mode reduces drying time by 50% vs. conventional ovens (ideal for ceramics, polymers, and PCB coatings).- Durability: SUS304 stainless steel chamber, fiberglass insulation, and powder-coated exterior for corrosion resistance.- Smart Connectivity: IoT-enabled remote monitoring via mobile app (iOS/Android), compliance with FDA 21 CFR Part 11 for audit trails.- Energy Efficiency: ECO mode reduces power consumption by 30% during idle (ENERGY STAR® 2025 certified).
-
product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
product
78-Pin D-Type Block Without Backshell
92-965-078-F
This connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
Connector Block, 78-Pin D-Type, Female
40-965A-078-F
The 40-965A-078-F connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell.
-
product
Block Down-Converter
RF Lambda’s block down-converters are used to convert higher frequencies down to IF. They can include front end amplifiers for lower noise figure and signal conditioning such as image rejection as required by the system.
-
product
Compensation Block for Thermocouple Simulator Modules
40-965-912
The Compensation Block is a accessory specifically designed for the 41-760 and 41-761 Millivolt Thermocouple Simulator modules. This block will give the user the temperature of the front panel junction of the module to cabling. This data can then be combined with other factors, temperature on the other end of the cable for example, to compensate the thermocouple hence increase the accuracy.
-
product
Frequency Block Converter
FBC
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
product
37-Pin D-Type Male Connector Block
40-965-037-M
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
200-Pin LFH Connector Block, Female
B200LFR-2F-5B
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
-
product
Laboratory Vacuum Oven, Laboratory Drying Oven For Ball Pressure Tester
CX-HTC
Shenzhen Chuangxin Instruments Co., Ltd.
laboratory vacuum oven,Laboratory Drying Oven for ball pressure tester
-
product
24 Block Desktop Receiver
VGR24
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
product
24 Block Desktop Receiver
VGR24-RM1
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
product
Microwave Drying Oven
SAM 255
The SAM-255 now with IntelliTemp Infrared temperature control provides rapid drying of all types of samples. The SAM-255 Workstation can analyze large-sized samples for moisture or solids.
-
product
Custom Pogo Pin Rings & Blocks
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
-
product
IP67 DC Blocking L-Band Splitter
PD5041
INSTOCK Wireless Components, Inc
PD5041 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5041 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
product
DC Blocking Power Splitter Combiner
PD7130
INSTOCK Wireless Components, Inc
True 3 Way Equal Split and BalanceWideband Frequency, 698-2700 MHzHigh Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) Low PIM
-
product
Quick Dry Rate Tester
Sataton Instruments Technology CO., Ltd
Quick dry rate tester is professional designed to determine the dry rate of fabric, which is exposed to a prescribed volume of water, tested surface temperature change, and time of drying. The tester is based on the heated plate method to determine the dry rate. It is applicable to all types of fabrics, including knits, wovens, and non-wovens, as well as to fabrics taken from end product items.
