Dry Blocks
-
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix topology With Column Protection Resistors
782385-12
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
Block Downconverter
RQ028
-
Teledyne Defence & Space (TDS) down converters are designed to convert digitised, band limited RF signal down to a lower frequency signal. These modules are used to reduce input signal which allows lower speed processors to better process fast incoming signals. A wideband mmW block downconverter suitable for extending the operational bandwidth of other devices into this range. With LO signals at 32GHz and 44GHz, two operational bands are available. Other frequency plans with and without pre-selection can be offered on request.
-
Product
Hybrid / Optical Dry Mate Connector
-
The Teledyne ODI Dry-Mate Submersible connector series is designed to directly complement the wet-mate hybrid connector series (Rolling Seal), and also for use as a stand-alone connection system. Two standard shell sizes are available, depending on the circuit configuration. In addition, straight, 45°, or 90° termination versions can be provided. Used in conjunction with Teledyne ODI's oil-filled hose, this system is designed for submersible applications up to 9,100 psi. A unique tri-lobe keying system assures proper alignment.
-
Product
DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband.
-
Product
DC Blocks
-
A coaxial RF DC block is from Pasternack and has an 50 Ohm impedance. Our 50 Ohm DC block is manufactured with a SMA input and SMA output. This SMA DC block is an inner direct current block type.
-
Product
Adapter & DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband. RF Lambda’s line of adapters are used to connect RF signals using different connector options.
-
-
Product
Data Block Mating Table
VG Series
-
*Aircraft, Consumer Electronics, Networking, Telecommunications and Test Systems*Custom Blocks can be designed for your specific applications please contact your local sales person to find out more
-
Product
Gain Block Amplifiers
-
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 10 MHz, a maximum frequency of 3 GHz and a typical gain of 20 dB.
-
Product
Dry Contact Control Unit
ZET 7161
-
The ZET 7161 is a three-channel control dry contact unit.
-
Product
Block Upconverter Modules
-
Analog Devices offers the most compact, robust portfolio of block upconverter solutions for high performance millimeterwave applications. Our block upconverter selection ensures that designers have access to the best performance and options for their demanding application and frequency conversion needs.
-
Product
Hardness Test Blocks
-
Used to verify the hardness tester's performance and provide data in order to calibrate the hardness tester.
-
Product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix Topology Without Column Protection Resistors
782385-03
Terminal Block
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
-
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
Product
DC Blocking L-Band Splitter Combiner
PD5940
-
INSTOCK Wireless Components, Inc
PD5940 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5940 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
Product
DC Blocking Power Splitter Combiner
PD7030
-
INSTOCK Wireless Components, Inc
True 3 Way Equal Split and BalanceWideband Frequency, 698-2700 MHzHigh Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy Type-N Female (Jack) Low PIM
-
Product
Terminal Block and SCSI-II 68 Pin Connector with 2 Meter Cable
U2902A
Terminal Block
The Keysight U2902A is an accessory compatible and recommended to be used with the U2300A Series USB Modular Multifunction Data Acquisition and U2500A Series USB Modular Simultaneous Sampling Multifunction Data Acquisition. The pin-outs of the U2902A is dependent on the USB Data acquisition unit that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2902A is to be used with.
-
Product
Connector Blocks for Interfacing to Ribbon Cables
-
VI Control Systems has designed several connector blocks for mating ribbon cables to screw terminals. Our design goal was to make the connector blocks small and inexpensive. Connector blocks are mounted by using 6-32 stand-offs. The connector blocks feature a ground plane that is connected to the mounting screw holes.
-
Product
DC Blocking Power Splitter Combiner
PD5020
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy Type N Female (Jack) Low PIM
-
-
Product
IPS Test Block & Plugs
-
The SecuControl IPS is the VDE-standard test block system for safe and structured IED testing in substations. Available in flush- or surface-mount versions, it provides a secure interface between relays and the system side, enabling reliable secondary injection without risk of open CT circuits or spurious trips. With finger-safe construction, keyed plugs, built-in CT shorting, and ultra-low resistance, the IPS combines safety, performance, and ease of use in a compact, standardized solution.
-
Product
DC Blocking L-Band Splitter Combiner
PD5980
-
INSTOCK Wireless Components, Inc
PD5980 is an IP67 outdoor, weather resistant, DC blocking, eight way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5980 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 8 way power divider input rating tables for additional power handling info.
-
Product
DC Blocking Power Splitter Combiner
PD5016
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
DC Blocking Power Splitter Combiner
PD5040
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Transducers, Cables, Couplants & Test Blocks
-
Olympus offers a complete selection of transducers, cables, couplants, calibration test blocks, and accessories to meet a wide variety of ultrasonic precision thickness gaging applications.
-
Product
Dry Cryogenic Systems
-
Part of the speciality of QMC Instruments Ltd, is integrating detectors and optics into cryogenic systems, which are suited to it's customers requirements. By packaging our detectors in this way we can ensure that they will perform exactly as quoted.
-
Product
Benchtop Electric Blast Drying Oven
-
Guangdong Test EQ Equipment co., Ltd.
- Precision & Uniformity: Multi-zone airflow design ensures ±2% temperature uniformity (per ASTM E1459). Auto-reversing fan eliminates hot/cold spots.- Rapid Drying: Turbo blast mode reduces drying time by 50% vs. conventional ovens (ideal for ceramics, polymers, and PCB coatings).- Durability: SUS304 stainless steel chamber, fiberglass insulation, and powder-coated exterior for corrosion resistance.- Smart Connectivity: IoT-enabled remote monitoring via mobile app (iOS/Android), compliance with FDA 21 CFR Part 11 for audit trails.- Energy Efficiency: ECO mode reduces power consumption by 30% during idle (ENERGY STAR® 2025 certified).
