Banks
-
product
Switch Filter Bank
Corech Microwave’s Switch Filter Bank frequency covers DC to 50GHz, featured with multi-channels (4 to 8 channels), high power handling, and fast switching options. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds.
-
product
8 Channel 100 MHz 12-bit ADC
SIS3300
The SIS3300 is an 8 channel 6U VME digitizer/transient recorder with a sampling rate of up to 105 MHz (for the individual channel) and 12-bit resolution. The board has a width of one VME slot (4TE). The boards multi event and dual memory bank functionality make the card the choice for many demanding digitizer applications.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 12-Bank 26.5GHz SMA
60-802-312
The 60-802-312 is a 4-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 3-Bank, 67GHz, 50Ω, SMA-1.85
60-803-803
Our 60-803-804 is a 4 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Low Voltage Capacitor Banks
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
product
LXI Microwave Multiplexer, SP6T, 14-Bank, 50GHz, 50Ω, SMA-2.4
60-800-614
Our 60-800-614 is a 14 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 4-Bank 26.5GHz SMA
60-802-304
The 60-802-304 is a 4-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 3GHz, 50Ω, MCX
40-873A-102
The 40-873A-102 (PXI) and 42-873A-102 (PXIe) are 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF1000
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations.
-
product
LXI Microwave Multiplexer, SP6T, 1-Bank, 26.5GHz, 50Ω, SMA
60-800-301
Our 60-800-301 is a 1 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 3-Bank 26.5GHz SMA
60-801-303
The 60-801-303 is a 6-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 8-Bank, 26.5GHz, 50Ω, SMA
60-803-308
Our 60-803-308 is a 8 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI 75Ω 6:1 Microwave Multiplexer 16-bank 2.5GHz 1.6/5.6
60-820-016
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
product
Digital Light Monitor
LMC-20
The LMC-20 functions not only as a light monitor for coating thickness, but also allows control of multi layer/multi material coating processes. Up to 2000 individual layers in a coating are possible, by using 40 program banks of 50 layers each. The characteristics of up to 99 different coating materials can be input as well. Final thickness can be calculated to 1% of a quarter wave.
-
product
LXI Microwave Multiplexer, SP6T, 14-Bank, 26.5GHz, 50Ω, SMA, Terminated
60-800-314
Our 60-800-314 is a 14 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
80 Channel Relay Multiplexer
DP-VXI-4017
DP-VXI-4017 is an 80 Channel Relay Multiplexer constructed using ‘2 Form A’ (DPST) relays. It is a ‘C’ size 1 slot register based VXI module. This 80 Channel Relay Multiplexer module is highly configurable. As an 80 channel multiplexer, one input can be multiplexed to any of the 80 outputs or vice versa. The 80 channel multiplexer is divided into 8 banks of 10 channels each. This combination allows the board to be used as one group of 80x1 or two groups of 40x1 or four groups of 20x1 or eight groups of 10x1 differential multiplexer. The banks are isolated from each other by tree switches. 8 tree switches are used, one tree switch for each bank. A common tree switch is used to group all the eight banks. For short circuit protection resistors are provided for all the common terminals.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 14-Bank 6GHz SMA
60-802-014
The 60-802-014 is a 4-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 12-Bank, 67GHz, 50Ω, SMA-1.85
60-803-812
Our 60-803-812 is a 12 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 4-Bank 6GHz SMA
60-802-004
The 60-802-004 is a 4-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Automatic Battery
BATLV400
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
product
LXI Microwave Multiplexer, SP6T, 12-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-512
Our 60-800-512 is a 12 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, SP6T, 7-Bank, 50GHz, 50Ω, SMA-2.4
60-800-607
Our 60-800-607 is a 7 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 11-Bank, 50GHz, 50Ω, SMA-2.4
60-803-711
Our 60-803-711 is a 11 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Acute High Voltage Differential Probe, 20x/200x, 100MHz, 1400V
ADP2100
*USB Powered (or Power Bank)*Bandwidth up to 100 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
product
Smartcard Interfaces
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
product
Automatic Capacitance Bridge Tester
HTDR-H / 395
Wuhan Huatian Electric Power Automation Co., Ltd.
Measurement of high voltage shunt capacitor banks for reactive power compensation devices.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 6-Bank 26.5GHz SMA
60-802-306
The 60-802-306 is a 4-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
NI-9206, ±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module
779526-01
±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module - The NI‑9206 performs differential analog input with four programmable input ranges. The module provides up to 600 VDC (400 VDC in Europe) channel‑to‑earth ground isolation, making the module ideal for accurately monitoring large fuel cell and battery stacks. By referencing the module common (COM) to the middle of the NI‑9206 bank, you can measure 16 consecutive cells and remain within 10 V of the module COM.
