Banks
-
Product
TMR Magnetic Pattern Recognition Sensors
-
MultiDimension Technology Co.,Ltd.
A type of 6 channels magnetic pattern recognition sensor built-in the signal conditioner and SPI interface Consists of TMR magneto-resistance sensor, high-quality magnet, high-strength plastic base and durable non-magnetic stainless steel cover; Are used for detecting the paper bills, bank notes and security documents with magnetic anti-counterfeiting consists.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 2-Pole
40-321-129-HI
-
The 40-321-129-HI (PXI) and 42-321-129-HI (PXIe) are single 48-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-510-003
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, SMB
42-872A-001
-
The 40-872A-001 (PXI) and 42-872A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Automatic Battery
BATLV400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 14-Bank 6GHz SMA
60-801-014
-
The 60-801-014 is a 6-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 11-Channel, 1-Pole
40-321-106-HI
-
The 40-321-106-HI (PXI) and 42-321-106-HI (PXIe) are quad 11-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
LXI Microwave Multiplexer, SP6T, 14-Bank, 50GHz, 50Ω, SMA-2.4
60-800-614
-
Our 60-800-614 is a 14 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP4T, 15-Bank, 50GHz, 50Ω, SMA-2.4
60-803-615
-
Our 60-803-615 is a 15 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
32GB SO-DIMM DDR5-4800 262Pin 2GX8 1.1V Unbuffered Samsung Chip
AQD-SD5V32GN48-SB
-
Samsung Original Chip, Dual 32-bit Subchannels, Increased Banks and Burst Length. DDR5 4.8GT/s, Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 11-Channel, 2-Pole
42-321-125-HI
-
The 40-321-125-HI (PXI) and 42-321-125-HI (PXIe) are dual 11-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI Multiplexer, 18-Bank, 3-Channel, 1-Pole
40-617A-021
-
The 40-617 18-Bank, 3-Channel, 1-Pole Multiplexer Module is part of our range of reed-relay based switching solutions. The Module consists of 18 electrically isolated banks of multiplexers controlled by a PXI/PCI interface. Each bank is a 1 to 3 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously.
-
Product
Resistive & Capacitive, Inductive AC Load Bank
RLC
-
Inductive & capacitive load banks are reactive only and must be used in combination with a resistive load bank to provide the desired load profile to test a power system. Reactive loads banks can provide either a leading power factor (Capacitive) or lagging power factor (Inductive).
-
Product
LXI Microwave Multiplexer, SP6T, 2-Bank, 67GHz, 50Ω, SMA-1.85
60-800-802
-
Our 60-800-802 is a 2 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-215-009
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Harmonic Filters
-
ENTES Harmonic Filter Reactors are used in serial connection with capacitor banks in power factor correction units. By using these types of detuned reactors it is possible to increase the capacitor impedance against harmonic currents and to keep the resonance frequency under the frequencies in which main harmonic currents occur by shifting the resonance frequency.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-210-002
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
8GB DDR5-5600 288Pin 1GX16 1.1V Unbuffered Hynix Chip
AQD-D5V8GN56-HC
-
Hynix Original Chip, Increased Banks and Burst Length, DDR5 5.6GT/s. Same-Bank Refresh, On-die ECC for Enhanced RAS.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-013
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI/PXIe Resolver Simulator Module, 2-Banks
43-670-203-AABBCC
-
The 41/43-670-203 is ideal for the simulation of Resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
LXI Microwave Multiplexer, SP6T, 3-Bank, 18GHz, 50Ω, SMA
60-800-103
-
Our 60-800-103 is a 3 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI 50Ω 6:1 Microwave Multiplexer 16-bank 40GHz SMA
60-800-416
-
Our 60-800 Microwave Multiplexer range is suitable for switching 50 ohm signals up to 40GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
-
Product
Transformer/Capacitor Test Sets
-
*Quick and easy check for opens or shorts on transformers or capacitors before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers as well as capacitors and capacitor banks*Tests the primary and secondary sides of de-energized transformers and capacitors without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer or capacitor*Automatic self-test featureMagnet holds the tester in place while testing
-
Product
LXI Microwave Multiplexer, SP4T, 10-Bank, 50GHz, 50Ω, SMA-2.4
60-803-710
-
Our 60-803-710 is a 10 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Multi-Unit Controllers
-
Mosebach Manufacturing Company
Mosebach’s Multi-Unit Controllers are built to help you manage your load banks in operation – whether 10, 20 or 500 units ganged together.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, MCX
42-876A-102
-
The 40-876A-102 (PXI) and 42-876A-102 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-874-102
-
The 40-874-102 is a 50 Ohm 8 to 1 RF multiplexer with 2 banks in a single PXI slot. It has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-874 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, SMB
42-837A-002
-
The 40-837A-002 (PXI) and 42-837A-002 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
4 2/3 Digits Voltage/Current Meter
CS2-VA
-
CS2-VA Voltage/Current Meter is designed with high accuracy measurement, display and communication of 0~600V or 0~10A for DC/AC/TMRS.● ADTEK builds flexible function as like as 3 bank (for multi-range scaling and set point) and 3 external control inputs meet to various testing equipment inquiry.They are also build in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 75Ω, SMB
42-832A-002
-
The 40-832A-002 (PXI) and 42-832A-002 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
