Reflectance
fraction of the electromagnetic energy.reflected.
-
Product
PXI-2545, 2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-45
Multiplexer Module
2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2545 is an RF signal multiplexer switch module. The internal termination of the PXI‑2545, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in RF applications where such reflections can damage the source. The module also provides excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
IR/Visible Target Projectors
-
Santa Barbara Infrared’s reflective infrared and visible target projectors are turnkey test systems for electro-optical (E-O) testing of FLIRs and other infrared (IR) and visible imaging systems. The standard target projectors are assembled from SBIR’s STC Series Collimators, Infinity Blackbodies, Infinity VSX Integrating Spheres and 300 Series Target Wheels.
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
-
Product
Bare Fiber Aligner
1120
-
The Photon Kinetics 1120 Bare Fiber Aligner makes it possible to reduce test setup time to seconds, thereby reducing overall testing cost. Just strip the fiber, scribe and break it (or use a more precise fiber cleaver, if desired) and then insert the prepared end into the 1120. In an instant, the fiber is coupled to your OTDR or chromatic dispersion test system with low optical loss and low reflectance. The 1120's compact, ergonomic industrial design is well-suited for low to moderate volume fiber and cable testing applications where automated fiber alignment systems are less economical. It is particularly useful as part of an in-process or finished cable test station employing either the 8000i or 8000 OTDR, and the OASYS.net OTDR Automation Software.
-
Product
Water Source Measurements You Can Count On
TechPro™ II (TP1, TPH1)
-
Obtain reliable and accurate measurements of your water source with the value-priced TechPro II™. Ideal for water treatment testing as well as other industrial and commercial applications, these instruments reflect Myron L®’s 55-plus years experience designing and building quality conductivity, TDS and pH measuring instrumentation.
-
Product
Instrumentation Tutor
-
Unitech Scales And Measurements Pvt. Ltd
This comprises of temperature and speed using different methods. RTD, thermistor and thermocouple are used as sensors with digital temperature indicator to measure temperature. A small water kettle is supplied as a temperature source upto 100°C. Glass bead thermometer is used as standard temperature measurement source to conduct the experiment. Magnetic and photo reflective sensors are used to measure speed. A FHP motor with speed regulator is used as speed source. To the shaft 60 teeth tone wheels are fixed to generate pulses.
-
Product
Silicon SPDT Switch Reflective, 100 MHz to 44 GHz
ADRF5024
-
The ADRF5024 is a reflective, single-pole double-throw (SPDT) switch manufactured in the silicon process. This switch operates from 100 MHz to 44 GHz with better than 1.7 dB of insertion loss and 35 dB of isolation. The ADRF5024 has an radio frequency (RF) input power handling capability of 27 dBm for both the through path and hot switching.
-
Product
Thermal Imagers & Industrial Endoscopes
-
GAOTek has developed advanced thermal imagers that are high quality, affordable, and accurate. Thermal imager is a non-contact temperature measurement device. It detects the infrared energy transmitted, reflected or emitted by all materials at a temperature above absolute zero. The energy factor is converted into a temperature reading or thermogram. Thermogram is the thermal image radiation produced that is displayed by the camera object emitting infrared energy. Thermal imagers are widely used for finding potential problems in applications across disciplines.
-
Product
Dynamic Mechanical Analyzers
-
Dynamic Mechanical Analysis measures the mechanical properties of materials as a function of time, temperature, and frequency. In addition to basic material properties, DMA also quantifies finished part characteristics, reflecting the important contribution that processing has on end-use performance. DMA is commonly used to measure glass transition temperatures and secondary transitions, orientation caused by processing, cold crystallization, cure optimization, filler effects in composites, and much more. DMA provides an accurate measure of material stiffness (modulus) but also other important mechanical properties such as damping, creep, and stress relaxation.
-
Product
ColorFlex EZ Citrus Spectrophotometer
Spectrometer
Hunter Associates Laboratory, Inc.
The ColorFlex EZ Citrus measures Citrus Number, Citrus Redness and Citrus Yellowness. These indices were primarily intended to score orange juice concentrate, but in practice have also been used for grapefruit and lemon juices. In addition to the citrus values, the instrument can also measure in terms of the Hunter Lab scale as well as other widely used color scales. Thus the system can also be used to measure the reflected color of virtually any opaque or semi-opaque liquid.
-
Product
Light-resistant Integrating Sphere
-
The integrating sphere is used for total luminous flux measurement. It uniforms the light by spatially integrating the collected light of light source. The integrating sphere has highly reflective diffusing plates formed on the spheres internal surfaces. These plates repeatedly scatter light rays from the light source with in the sphere to all other points to deliver uniform brightness distribution so measuring a portion of that light gives the total luminous flux. These years, the usage of integrating sphere for total luminous flux evaluation of light source is increasing. The large size integrating sphere over 1.5M is required for measuring a high brightness light source and a long light source such as fluorescent light.
-
Product
Industrial Inspection Cameras
-
Industrial Inspection Cameras are our top-of-the-line inspection cameras. They feature glass lenses, superior optics, crystal-clear displays, and compatibility with the thinnest probes on the market. All Industrial Inspection Cameras were recently upgraded to capture VGA (640 x 480 pixel) resolution video clips and remove glare and reflections from them. All cameras in this sub-category are made in Taiwan, making them compliant with the Trade Agreements Act (TAA) of 1979a necessity for many buyers with the U.S. military and federal agencies.
-
Product
General Purpose Integrating Spheres
-
General Purpose Integrating Sphere Systems are designed to spatially integrate radiant flux in order to measure optical radiation. The spheres can be coupled with a sensor to create radiometers, photometers, or spectroradiometers in order to measure the total geometric flux emanating from a light source or the flux density of an illuminated area. Additionally, these sphere systems can be used to measure the output of high power lasers and laser diodes or to measure the reflectance and transmittance of materials.
-
Product
SP3T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
Product
Sensors
Chromatic Focus Probe
-
Measurement of highly reflective, absorbent and transparent materialsMeasuring results are independent of the surface propertiesEspecially suitable for fast and precise measurements on reflective surfaces, lenses, prisms and other optical devicesFlexible probe configurations for highly customized applications
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Evaluation Services
-
Atlas Material Testing Solutions
Atlas offers a wide range of evaluation and measurement services for our client's specimens during and after the weathering process. These services are available at Atlas' Miami, Florida and Phoenix, Arizona sites. Atlas uses the most advanced instrumentation from leading manufacturers for measuring appearance properties such as color change, gloss, distinctness-of-image, transmittance and reflectance. All of our services meet the latest measurement test standards from organizations such as ASTM, ISO, DIN and others. A full range of visual assessment services is also available, including coating adhesion, blistering, chalking, cracking, mildew growth, and gray scale evaluation in accordance with respective standards' organizations. Temperature monitoring programs are provided for single and multiple specimens under any type of exposure, as well as for large assemblies such as complete vehicles. Strict quality control guidelines have enabled Atlas' Evaluations Laboratory to achieve industry-accepted accreditation from world renowned standards' organizations. Atlas is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) and accredited or approved by Ford, GM and AMECA.
-
Product
Digitize, Quantify, Collaborate With Your Unique Automated Petrographic Microscope
ZEISS Axioscan 7 for Geology
-
Digitize your thin sections with Axioscan 7 – the reliable, reproducible way to create high quality, digitized petrography data in transmitted and reflected light. Uniquely designed for petrographic analysis, the Axioscan 7 Geo combines unique motorized polarization acquisition modes with unprecedented speed and a rich software ecosystem for visualization, analysis, and collaboration.
-
Product
Adjustable Range Reflective Photoelectric Sensor
EQ-500
-
Panasonic Industrial Devices Sales Company of America
The EQ-500 Series Adjustable Range Reflective Photoelectric Sensor is a multi-voltage compact Reflective Photoelectric Sensor that can function with 24 to 240 V.AC and 12 to 240 V.DC, to operate with any power supply around the world. Background and foreground suppression (DC Types) and a long sensing range of up to 2.5m is a key characteristic of the EQ-500 Sensor. With an IP67 rating, the EQ-500 can be used in harsh environments prone to water or dust making stable sensing possible.
-
Product
Minority Carrier Life Time System
MWR-SIM
-
MWR-SIM Lifetime determination is based on measuring photoconductivity decay after pulselight photo-exciting with usage of reflected microwave as probe.It enables repetition and contactless of measurement and does not require specialsurface treatment before measurement or wafer cutting.
-
Product
IR Receivers
-
Vishay is the world's leading supplier of infrared (IR) receivers. Vishay IR Receivers offer a breadth of products, holders, application and technical support, and overall knowledge of infrared communication; infrared code learning, infrared light barriers, infrared proximity sensors including reflective sensors. Vishay's IR receivers are used for remote control and for transmissive and reflective sensors.
-
Product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
RF Multiplexer
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
Product
Optical Detector
LG-9200
-
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
Product
Coaxial Open, 2.4 mm (m)
85141A
Terminator
The Keysight 85141A coaxial open is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm male connector.
-
Product
Pull Off Tester
Serie DY-2
-
The DY-2 FAMILY of automated pull-off testers covers the complete range of pull-off applications with unmatched ease of operation and a unique capability to store a complete record of the test.Pull-off testing is one of the most widely used test methods in the construction industry. This is reflected in the huge number of standards dedicated to the method.
-
Product
50% Beam Splitter
10701A
-
The Keysight 10701A beam splitter is designed for beam diameters of 6 mm or less. It reflects one half of the total incoming laser beam, and transmits one half. The Keysight 10701A optic includes a housing for standard mounting.
-
Product
Illuminate Reflective Test Charts
iQ-Chart Box
-
Image Engineering GmbH & Co. KG
The iQ-Chart Box makes it possible to illuminate reflective test charts quickly and homogeneously. It is the compact solution for providing optimal conditions for the image quality testing of cameras and cell phones. Whether measuring resolution or color reproduction, all reflective test charts that we offer in the A460size can be used. Chart changing is carried out quickly and easily by means of a movable carriage. The lighting systems in the iQ-Chart Box are precisely aligned and fixed; the test charts are always optimally and homogeneously illuminated.
-
Product
S-Parameter Measurement System
DPS08
-
KEYCOM provides S-parameter method measurement systems in two modes, the reflection mode and the transmission mode, to address the individual purposes. Both modes measure the complex permittivity (εr) and complex permeability (μr) at the same time, and the proper usage is as follows.
-
Product
UltraScan VIS Spectrophotometer
Spectrometer
Hunter Associates Laboratory, Inc.
The UltraScan VIS easily measures both reflected and transmitted color as well as transmission haze and meets CIE, ASTM and USP guidelines for accurate color measurement. UltraScan VIS uses diffuse/8° geometry with automated specular component inclusion/exclusion. For transmission measurement, the use of a robust CIE-conforming sphere instrument (TTRAN Total Transmission mode) effectively negates the effects of minor scattering typically found in transparent samples.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TV
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used for measurement of DCcurrent etc. The output of the transducer reflects the real wave of the current carrying conductor.
