-
Product
Digital Step Attenuators
-
Ranatec’s digital step attenuators covers all mobile frequency bands and gives a calibrated attenuation range of more than 90 dB in steps of 0.25 dB. All Ranatec digital attenuators are built as modules and offers both serial and parallel control logic.
-
Product
Power Supply, 300V, 17A, 5100W
N8761A
Power Supply
The Keysight N8761A is a 300V, 17A, 5100W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
Product
Integrating Spheres
-
Integrating spheres are used especially for measuring divergent light sources such as LEDs. The light is introduced through the input port, then reflected many times by the highly reflective interior of the sphere until it illuminates the inner surface uniformly. A detector samples a small fraction of this light to measure the total power input. Ophir integrating spheres have a highly reflective diffuse white coating for measurements independent of beam size, position and divergence. There are several sphere sizes, apertures and wavelength regions available. The large IS6 series has 2 configurations for measuring divergent or parallel beams.
-
Product
Ultrasonic Thickness Gauge
UTG-1500
-
The new PHASE II UTG-1500 is a hand held microprocessor controlled ultrasonic thickness gauge specifically designed for measuring the thickness of metallic and non-metallic materials such as aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wave-conductor as long as it has parallel top and bottom surfaces.
-
Product
High Performance DC/DC Converters
-
The 4:1 Input Voltage 1000 Watt Single FXP DC/DC Full Brick converter is designed to operate in parallel with up to 3 FXP bricks (2800 Watts) with no external circuitry. The FXP series provides a precisely regulated DC output. The output voltage is fully isolated from the input, allowing the output to be positive or negative polarity and with various ground connections.
-
Product
Linear regulated power supply with thyristor pre-regulation
NTN
-
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Product
Exchangeable Test Fixture
MA 2109/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
Product
Battery Capacity Tester
BLU-T Series
-
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.
-
Product
Power Supplies
-
Our short-circuit-proof, single or triple-phase power supplies for automation are approved according to CE/TÜV, UL and CCC. Different voltages of 12 V, 24 V and 48 V can be selected. The most important features: top-hat rail assembly, status display, regulatable output voltage, parallel connection, ready and alarm output. Output power of 18 to 960 W. Protection class IP20.
-
Product
NTDS I/O Analyzer
-
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
Product
Hyperspectral Cameras With USB3 Vision
XiSpec
-
*Smallest Hyperspectral camera - Compact, lightweight with only 26.4 x 26.4 x 31 mm, 32 grams (1)*Cost efficient - Excellent value and price through utilizing new imec hyperspectral imaging technology*Cool economy - Low power consumption with 1.6 Watt, minimal heat dissipation, ideal for UAV / UAS*All-around support - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM*Powerful potential - Highest spatial and spectral resolution, possible with 5Gb/s interface*Optimized - 2048 parallel, "on-chip" integrated spectroscopes with 100 points of spectral resolution each*AIA standard - USB3 Vision standard compliant*Industry standard interface - Compatible with USB 3.0 SuperSpeed specification*Fastest Hyperspectral camera - High speed, high frame rate: based on 170 fps at 2.2 Mpix resolution*Connectivity and Synchronization - Programmable optoisolated input and output, 3 status LEDs*Easy deployment - Range of accessories and wide hardware and software integration*Highly Customizable - Variety of sensor options, which can be further adjusted to match requirements*Interoperability increase - Continuous embrace of new software and hardware partners
-
Product
Window Tint Meter
-
Guangzhou Amittari Instruments Co.Ltd
The Window Tint Meter is applicable to measure the transmittance or haze of all kinds of transparent, translucent samples with parallel plane (such as automobile manufacturing, aerospace, glass products, plastic sheet, sheet, etc). Also can be used to determine the turbidity or clarity of liquid sample (water, drinks and so on).
-
Product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
-
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps.
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
TestStation Multi-Site Offline
-
TestStation Multi-Site Offline provides true parallel test, delivering 200% to 400% greater productivity, and 40% to 50% lower total cost of test.
-
Product
VITA 57.4 FMC+ HSPC Loopback Card
-
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
Product
Benchtop Unit for Universal Coating Thickness Measurement
FISCHERSCOPE MMS PC2
-
Multifaceted for coating thickness measurement and material testing. Universal multi-measuring system for parallel coating thickness measurement and material testing with up to eight measuring modules.
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
1 KN Eccentric Roller Grips
-
These eccentric roller grips are specifically designed for tensile testing flexible materials, such as rubber and soft and semi-hard plastics. Named after the non-symmetric roller design, these grips employ a simple and quick clamping mechanism. They also have a self-tightening action, which maintains clamping of the specimen during testing regardless of any thickness reduction. In addition, the upper and lower grip faces are parallel grooved to help hold these soft materials.
-
Product
256 Channel Power Supply
IDPS750
-
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
Product
Test Database Software Module
-
The relational test database is the pivotal point of the software structure. On one hand, this is where the test applications and test systems used for productive testing are stored; on the other hand, it provides the storage space for all DUT-related test data. Depending on customer requirements, the test database may either be hosted locally on the test system or centrally on a server, supporting several test systems. The database performance is sufficient for a high-volume production environment with many test systems which access the central database in parallel. LXinstruments prefers to implement the database as a license-free MySQL database; it is however also possible to realize a version based on Microsoft SQL.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
Digital I/O
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
Product
2-Slot BRIC, 256x4, 1Pole, PXI Matrix (2 Sub-cards)
40-559-201-256x4
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays. With their high level of switching density, these PXI matrices allow a complete Functional ATE system to be housed in a single 3U PXI chassis and allow the use of much lower cost 8 or 14-slot chassis. The 40-559 matrices can be used in many industries; typical applications include automotive ECU and semiconductor package testing. Dual analog busing for the narrower matrix options, enable completely separate matrices within a single module for parallel testing.
-
Product
Advanced SoC Test System
3680
Test System
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
Product
CSvideo | CTvideo | CSvision Series Infrared Thermometer
-
The video pyrometer series optris CSvideo/CTvideo and the new innovative ratio pyrometer CSvision allow a parallel use of video and crosshair laser aiming for an optimal measuring field adjustment even in processes with limited access. They reliably measure temperatures of metals or ceramics and, due to their short measuring wavelength, reduces measuring errors of surfaces with low or unknown emissivities. The high quality video sighting can show its full advantage together with the software CompactPlus Connect or the IRmobile App on your cell phone with state-of-the-art zoom and image rotation features. The adjustable focus, motorized on CSvision, allows an optimal adaptation to different application and installation demands. As CSvision can measure objects up to 3000 °C a unique two-step brightness reduction filter (BRF) is giving the user a tremendous advantage when aiming on hot and extremely bright objects.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
Digital I/O
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
Haze Meter
HAM-02
-
Jinan Leading Instruments Co., Ltd.
HAM-02 Haze Meter is a kind of small hazer meter designed according to ASTMD1003—61(1997). It is applying to test the light transmittance,transmission haze, and reflection haze, reflectivity of transparent and semitransparent parallel level material and plasticfilms. Also it is suitable for liquid samples (water, beverage, pharmacy,colored liquid, grease) turbidity measurement. It is the basic instrument for plastic, glass products, all kinds oftransparent packaging films, colored and colorless of organic glass andaerospace, automotive glass and photographic film.
-
Product
VLSI Test System
3380D
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
