Serial Interfaces
one conductor one bit at a time data transfer.
See Also: Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, PXI Serial Interfaces, Parallel Interfaces
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
40-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
ARM 9 System on Module
MS 1515
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
Product
DH Series QuickLink Adapter Kit with 3 x QL-SI Tips
DH-QL-3SI
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PXIe-8431, 8-Port, RS485/RS422 PXI Serial Interface Module
781473-01
Serial Interface
The PXIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Flash SATA DOM
FSD Series
-
Axiomteks FSD (Flash SATA DOM) series is designed into Serial ATA II protocol type with compatible Serial ATA standard interface based on flash memory technology. This flash module is offered with various capacities ranging from 128 MB up to 32 GB and can operate under industrial temperature range goes from -40°C ~ 85°C in the harsh operating environments. The features of reliability, high performance, cost-effective and easy-tointegrate designs make FSD series a perfect solution over traditional storage devices.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
JadeFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5983-317
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- VITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB and 5 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and synchronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
Serial Controlled Relays And Relay Drivers
-
*ICS's Serial controlled Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Serial to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any Serial programming language. Use ICS's interactive Serial Keyboard program for easy operation from your PC without having to write a program.
-
Product
Counters and Timers
-
Orbit Controls counters and timers are designed for connection to practically all industrial sensors and pulse sources . They can be used as process monitors to display the process variable to be measured or as process controllers for control and monitoring tasks. The devices display and process pulses and frequencies, as well as quadrature signals from incremental and absolute encoded rotary encoders. In addition to information on the display, the devices also generate data and analog outputs and monitor preselected limit values. The process parameters are entered via the keyboard so that the display is calibrated in the required units and the output signals, serial interfaces and limit values are optimized.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
C/D-PHY CSI-2/DSI Analyzer
Envision X84
Analyzer
is the first combination C-PHY/D-PHY analyzer in single platform. The Envision X84 supports C-PHY/D-PHY and Cameral Serial Interface (CSI-2) and Display Serial Interface (DSI/DSI-2) on a single hardware platform. Envision X84 supports C-PHY version 1.1 and D-PHY 2.1 as well as CSI-2 version 2.1 and DSI version 1.3 and DSI-2 version 1.1. The Envision X84 offers Silicon ad device designers, integrators and validation engineers a complete, robust yet flexible tool to ensure the correct and efficient operation of Camera and Display over C-PHY and D-PHY implementations.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
Serial Interface
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
GPIB to Quad Serial Interface
Model 4896
-
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
PCI Express 8-Port
7804ec
-
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI Differential Fault Insertion Switch Modules
-
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 57690
-
- One L-Band tuners accept RF signals from 925 MHz to 2175 MHz- One programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- One programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Universal PCI, RS-422 Or RS-485 Serial Interface Cards
LPCI-COM422-8 and LPCI-COM485-8
-
These are eight-port, asynchronous, serial communication cards designed for use on the PCI bus. They support RS-422 or RS-485 communications. These cards offer the best combination of high-density and high-speed communications in a low profile form factor. The cards meet the MD2 Low Profile PCI Bus Specification and can be used in applications where space is at a premium, such as thin-client servers and high-density rack-mount servers. The LPCI line has been designed for use in retail, hospitality, and point of sale systems as well as the gaming and defense industries.
-
Product
72 channel FPGA Logic Module
XLM72
-
XLM72 is a FPGA based logic module with 72 I/O ports. Featuring two 64 Mbit SPI (Serial Peripheral Interface) memories, from one of which its FPGA boots upon power-up, complex logic operations can be programmed and saved on-board.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
Relay
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC, Virtex-6 FPGA - 6U VPX
Model 57662
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- 32 channels of multiband DDCs (digital downconverters)- Up to 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
OnyxFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5973-317
-
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)Ruggedized and conduction-cooled versions available
-
Product
Multiplexer 2:1 With De-Emphasis 32 Gb/s
M8062A
Multiplexer Module
R&D and test engineers who need to characterize serial interfaces of up to 32.0 Gb/s can use the M8061A 2:1 Multiplexer with optional de-emphasis to extend the rate of J-BERT M8020A and J-BERT N4903B pattern generator. For the most accurate receiver characterization results, the M8061A provides four calibrated de-emphasis taps, which can be extended to eight taps, built-in superposition of level interference and Clock/2 jitter injection. The M8061A is a 2-slot AXIe module that can be controlled via USB from the user interface of J-BERT M8020A as well as N4903B.
-
Product
3 Channel Sync/Async Serial Interface PCI Mini Card
TMPE863
-
The TMPE863 is a standard full PCI Express Mini Card, providing three high speed serial data communication channels.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 16-Channel, 2-Pole
42-739-001
Multiplexer Module
The modules are ideal for the testing of multiple devices that use a serial communication interface, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance. The module uses long lifetime electromechanical relays characterized for use in communications systems.
-
Product
Dual L-Band RF Tuner and 4-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 58791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Two programmable LNAs handle L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Four FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Digital Sequencers
-
The Analog Devices Super Sequencer ® portfolio offers a total power management platform for monitoring, measuring, sequencing, and margining a large number of voltages. Our comparators provide ±1% accurate monitoring of rails, while 12-bit ADCs offer voltage readback via a serial interface. Applications utilizing these devices benefit from sequencing that has been custom tailored to their needs by powerful state machine cores, as well as DAC banks to trim or margin regulators. Our digital sequencers include on-board EEPROM for storing devices parameters and for latching information for later analysis.
