Serial Interfaces
one conductor one bit at a time data transfer.
See Also: Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, PXI Serial Interfaces, Parallel Interfaces
-
product
2-Channel 400MHz DDS Signal Generator
2940A
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
product
Floating-Point C6678 DSP Module
FMC667
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
product
1 GHz A/D and D/A with Virtex-6 FPGA - XMC
Model 71630
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronizationPCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Low Profile PCI Express 8-Port
7803ec
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - XMC
Model 71760
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Advanced reconfigurability features- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Modbus TCP Gateway
SI-485MB
SI-485MB is a Modbus gateway to convert bi-directionally Modbus RTU/ASCII of serial interface to Modebus TCP of Ethernet. The firmware for gateway process supports Modbus TCP master mode and Modbu TCP slave mode and supports all the current ModbusRTU/ASCII register and command conversion. The robust metal body, broad range of temperature, wide input voltage range, and the support for installation by options such as 35mm DIN rail and wall bracket allow you to use it for factory automation without worry.
-
product
DH Series High-Sensitivity Solder-In Tip, 30 GHz BW, 2.0 Vpp Range
DH-SI-HS
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Silicon Oscillators
Analog Devices silicon oscillators are frequency programmable via pin-strapping, or through the resistor connection or serial interface (SPI or I2C). These solid-state clocks are well-suited for general-purpose usage, such as PGAs, ASICS, microprocessors, or UARTS, and they operate from 1 kHz to 170 MHz. Silicon oscillators are also ideal switching regulator clocks as they provide synchronization and EMI reduction (via spread spectrum).
-
product
Intelligent Power Monitor
iPM
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
product
Oscilloscope
DSO Coral 112A
*Maximum sensitivity was increased to 2mV/div (older version is 5mV/div) with lower background noises*Fixed the vertical position mismatch problem found in the older model*Save/recall up to 24 parameter presets. This allows quick setup for frequently performed measurements*Preset titles can be customized for easy remembering and identifying*Expanded and improved on-screen measurement displays which include frequency, Vmax, Vmin, Vavr, Vpp, and Vrms*Added external trigger feature*Provided a two-way serial control interface which can output data/measurements and receive commands. This will make the device suitable for integration to customer applications*Replaced out-dated miniUSB connector with more popular microUSB connector*Enclosure strength enhanced
-
product
RFID
HF (13.56 MHz)
BIS M uses the high frequency (HF) 13.56 MHz and supports the standard according to DIN ISO 15693 and 14443. Communication modules/gateways are used for the point-to-point or bus linking and are directly connected to a serial interface of a PC/a bus interface. The Subnet16 TM bus architecture supports a subnet of up to sixteen nodes via an RS485 interface.
-
product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Wide Band Filters (multi-octave)
ERF-5W™ Series (Single & Dual)
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
product
RFFE Protocol Analyzer and Exerciser
PGY-RFFE-EX-PD
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
product
Extension Module
GE-DIO-42
Infinite Industrial Informatics Lt
GE-DIO-42 is a digital I/O, DIN rail mount expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
product
Engine Control
StepGenerator4
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
product
LIS3DH 3-Axis Accelerometer With ADC
29020
The LIS3DH is a high performance, ultra-low power, three-axis linear accelerometer. It features user-selectable scales up to 16g, an embedded temperature sensor, 10-bit ADC and a standard digital I2C/SPI serial interface.
-
product
ARM LPC2294 Based Board
MS 2500
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
product
Analog Interface Boards
Model 4861B OEM
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
product
Low Profile PCI Express 8-Port
7803e
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
8-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - 6U VPX
Model 58670
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 1.25 GHz 16-bit D/As- Eight digital upconverters- Programmable output levels- 250 MHz max. output bandwidth- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Quad µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
4-Port Serial Interface
APCI-7500-3
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
product
Intel 80486 DX2 Processor Board
MS 1500
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
product
PXI-8430, 16-Port, RS232 PXI Serial Interface Module
779948-01
16-Port, RS232 PXI Serial Interface Module - The PXI‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Single Port Serial Interface
APCI-7300-3
*PCI interface to the 32-bit data bus. *Asynchronous communication adapter, 1-port serial interface*1 socket for SI modules*Modular structure through SI modules*Configurable as: RS232, RS422, RS485, with or without isolation, or 20 mA Current Loop (active, passive) with isolation*Addressing through software
-
product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 58720
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Dataloggers
Data loggers with one or more signal channels for DC and AC voltages and currents, thermocouples, Pt thermometers, process signals and serial data interfaces RS232 / RS485 are designed for industrial use. They can also be used as monitors or process controllers with additional data and signal outputs for control purposes. The devices are designed for panel construction and have communication software for Windows applications.
-
product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
