Parallel Interface
Connection between devices transmitting information through multiple conductors simultaneously.
See Also: Interfaces, Serial Interfaces, Bus Interfaces, UI, MIPI, Interface Adapters
-
Product
Serial Parallel Interface
Model 2313
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
Product
GPIB Parallel Interface
Model 4813
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
Product
GPIB Parallel Interface
Model 4803
-
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
Product
GPIB to Parallel Printer Interface
Model 4892B
-
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
Product
Parallel Interface Voltage Output D/A Converters
-
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
GPIB Parallel Interface
Model 4823B
-
* Provides 56 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Available with DIN connector on circuit side for piggyback mounting.
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
Ethernet Parallel Interface
Model 8013
-
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
Product
PXIe Remote Control Interface Module with Daisy-Chain Facility
43-921-001
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
Product
PCIe-8244, 4-Port, USB3 Vision Frame Grabber Device
782890-01
-
The PCIe‑8244 is a USB 3.0 interface device designed for use with USB3 Vision cameras. USB 3.0 is ideal for high-data-rate machine vision applications. USB3 Vision cameras also offer plug‑and‑play functionality and ease of use through a standardized catalog of functions.
-
Product
PXI-8532, 1-Port, PXI DeviceNet Interface Module
781063-01
-
1-Port, PXI DeviceNet Interface Module—The PXI‑8532 is a high-speed DeviceNet interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the CAN physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. DeviceNet specifications are managed by OVDA, Inc. You can program the PXI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
Product
Interface
3508 MMS ECM
-
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
PXI-8360, MXI-Express Interface, PXI Remote Control Module
779501-01
-
MXI-Express Interface, PXI Remote Control Module—The PXI‑8360 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8360 through a copper, x1 MXI‑Express cable.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
-
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
-
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Device Interface
-
Providing flexible, dependable services for device interface design, development, ordering, production, and support. The importance of the device interface has greatly increased, as high speed, high density semiconductor devices are more rapidly developed, and as customers more severely demand high accuracy, high reliability, and high productivity of testing.
-
Product
Embedded Avionics Interfaces
-
Versatile interfaces that enable embedded systems and computers to communicate with avionics databus networks.
-
Product
Interface
P-SER
-
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
Portable Avionics Interfaces for USB 3.1
UA2000
-
The all-new USB 3.1 design and low-power requirements mean the UA2000 is compatible with USB 2, USB 3, USB 4, and Thunderbolt™ ports. The product ships with both USB-C and USB-A cables for easy connection to current and future computer ports.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
-
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
2U Through 6U Customized RF Interface Unit
1257A-C
-
The Astronics 1257A-C is a sixth-generation RFIU tailored to your specifications. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including 2U through 6U configurations.
-
Product
Interface
RAR-MPCIE
-
The RAR-MPCIE is very small (30mm x 40.95mm x 4.7mm) and lightweight for applications deployed in highly constrained environments where platforms require minimum SWaP solutions. It is designed for those working in avionics test and simulation for field and test support, and for use in data logging in which it offers significant advantages and flexibility.
-
-
Product
Interface Board, Low Cost, 8:1 Ethernet RJ45
40-965-901
-
Low cost converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
Application Programming Interface Software
AltaAPI
-
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
-
Product
Interface
RCEI-530
-
Available in a range of configurations to match your needs, the RCEI-530 provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols. The RCEI-530 supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, time-tagging, error detection and avionics-level I/O discretes, with support for either 33 MHz or 66 MHz PCI interfaces.
-
Product
Interface
RAR-PCIE
-
Available in a range of configurations to match your needs, RAR-PCIE provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols.
