Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
PCI Multifunction Board
PCI-1202H/S (with DB-1825 daughter board & cable)
-
The PCI-1202 series is a family of high performance data acquisition boards for the PCI bus. It features a continuous, 110KHz for low gain (40KHz for high gain), gap-free data acquisition under DOS and Windows. The PCI-1202 family has the same hardware architecture as PCI-1802. The PCI-1202 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1202 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
Dual 16x8 1-Pole High-Density PXI Matrix Module
40-520-205
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
-
Product
Xcelera Frame Grabber
Xtium-CLHS PX8
-
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CLHS PX8 is based on AIA’s CameraLink HS standard and uses PCI Express™ Gen 2.0 expansion bus to deliver high speed image acquisition and image transfer to the host memory. Xtium-CLHS uses industry standard CX4 cable to delivery up to 2.1 GB/s of image acquisition over a single cable to go beyond 15m and host transfer speeds of up to 3.2GB/sec - all in a compact, half-length, single slot solution.
-
Product
CM AXIe-0 system module
CM AXIe-0 MODULE
-
CM AXIe-0, made in the AXIe standard, is designed to work as part of measuring systems created on the basis of the AXIe-0 backbone. CM AXIe-0 is intended for use as part of AXIe-0 standard crates with the number of seats (slots) not more than 14. CM AXIe-0 complies with the requirements of the AXIe-0 standard for system modules of the AXIe-0 bus.
-
Product
L-Band RF Tuner and 4-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 58690
-
- Two L-Band tuners accept RF signals from 925 MHz to 2175 MHz- Two programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- Two programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Four 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Logic analyzers, MSOs
-
This digital logic analyzer has basic functions, easy operation and a new way of measuring data for monitoring and measuring signals in digital information processes. Thus, the device allows the analysis and troubleshooting in digital systems, such as transmission delays to be analyzed and the result of the information processing of the digital circuit and bus technology.
-
Product
8/16-CH 16-Bit 250 kS/s Multi-Function USB DAQ Modules (OEM Version Available)
USB-1901/1902/1903
-
The ADLINK USB-1900 series provides a range of USB 2.0-based multi-functional DAQ modules. The USB-1901 and USB-1902 16-bit 250 kS/s USB 2.0-based high-performance DAQ modules allow four different voltage input ranges, while the USB-1903 features additional built-in precision current-tovoltage resistors capable of direct measurement of current signal from 0 to 20 mA. The USB-1900 series is USB bus powered and equipped with removable screw-down terminals for easy device connectivity. The attached multi-functional stand can be used for desktop, rail, or wall mounting. Suitable for mixed-signal tests, laboratory research, and factory automation, the USB-1900 series provide a simple measurement solution at an affordable price.
-
Product
Electric Vehicle Charging Infrastructure
-
ABB lays the foundations for a future of smarter, reliable, and emission-free mobility, accessible by everyone, everywhere. ABB offers a total ev charging solution from compact, high quality AC wallboxes, reliable DC fast charging stations with robust connectivity, to innovative on-demand electric bus charging systems, we deploy infrastructure that meet the needs of the next generation of smarter mobility.ABB Ability™ connected chargers enable fast global service and pro-active maintenance. ABB has years of experience in creating, installing and maintaining charging infrastructure, including several nationwide charger networks.
-
Product
VME64x IP Carrier Module
DP-VME-5121
-
Data Patterns DP-VME-5121 VME IP carrier board is a 6U VME bus card that provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.Each IP module supports two interrupt requests. The VME bus interrupt level is software programmable. The software configured interrupt modes are:a.Single level interrupt mode: All IP module interrupts can be mapped to a single VME bus interrupt level.
-
Product
Complete IP Module
Scan Ring Linker SRL
-
The Scan Ring Linker SRLTM - is a complete IP module that can be easily embedded into a CPLD, FPGA or ASIC on a PCB to reduce the complexities and costs of designing 1149.1 (JTAG) test infrastructure for designs that use multiple scan rings. The SRL IP module links any number of scan rings (secondary scan paths) into a single high-speed test bus, which permits devices on secondary scan chains to be independently tested and configured through a single 1149.1 external interface.
-
Product
PCIe Basic Protocol Tx and Bus Monitor
Sy629PCIe-BPM
-
The Sy629PCIe-BPM card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory.
-
Product
Beagle USB 480 Protocol Analyzer
TP320510
-
The Beagle™ USB 480 Protocol Analyzer is a low cost, non-intrusive High-speed USB 2.0 bus monitor that includes real-time USB class-level decoding.
-
Product
ETX Development Baseboard
ETB9F000
-
The ETB9F000 has four PCI slots and three ISA bus expansions as well as CompactFlash™ Type II socket. Most I/O functions have been integrated into this baseboard.
-
Product
PXI Express Board
SMT722
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
ccVPX Card
EXC-4500ccVPX/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-4500ccVPX/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch, N/O Through Relays
40-190B-302
-
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Low-cost Cable/terrestrial Modulator For PCI
DTA-111
-
Low-Cost VHF/UHF Modulator for PCI Bus
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 3U VPX
Model 52141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
4-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - XMC
Model 71670
-
- View product video- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface, up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI 8 Slot BRIC 276x8 1-Pole Dual Analog Bus (6 sub-cards)
40-560A-121-276X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Ground Grid Tester
GGT Series
-
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.
-
Product
Audio Board
MS 1813
-
*Two Audio Output Channels (Playback)*Two Audio Input Channels (Recording)*High performance Stereo Audio Codec*PCI Bus Interface
-
Product
High-Performance Integrated Functional Test Platform
Spectrum-9100™
-
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
Product
Programmable Multifunction Counter Board, Isolated, With 4 Function Modules
CPCI-1710
-
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
Product
VPX Interposer
VPX850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
RTM Digital & Analog IO Board
-
*Bus Interface:- 16 Bit Data bus, 8 Bit Address Bus*Spartan-3AN FPGA based design
-
Product
Fixture Interface Module 2 Test Matrices
OTP2 module no.193
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
-
Product
Avionics Test & Simulation Software
-
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
Product
MIL-STD-1553 IRIG 106 Chapter 10 Streaming Application
F-SIM-1553-CH10-STREAM
-
Avionics Interface Technologies
Streams MIL-STD-1553 Data from AIT MIL-STD-1553 interfaces in Chapter 10 Format - Software application which is Compatible with all AIT MIL-STD-1553 Interfaces - Capable of streaming data captured from one or multiple MIL-STD-1553 Bus Interfaces - Streamed data can be sent to a single network system or multicast on the Ethernet LAN - Compatible with AIT F-SIM-1553-AVOE analyzer or 3rd party Chapter 10 systems - Timestamps & Errors detected embedded in Chapter 10 stream
