Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
PCI to PC/104+ Bus Adapter
327/328
-
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
Product
FR-Net Data Acquisition
-
FRnet Protocol developed by ICP DAS is an easy to use industrial field bus offering high-speed deterministic I/O control, real I/O synchronization capabilities, and non-protocol communication. We provide FRnet remote I/O modules and high speed controllers.
-
Product
Data Stream Digital Transducers
-
The Data Stream Series provides a digital stream of data that can contain complete electrical properties information including current, voltage, power, phase angle and frequency. Additionally, an energy totalizer can be configured to give total energy calculations. All data is transmitted via an RS485 bus, and a single bus can communicate with multiple devices. MODBUS capable programming is also available.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
OBD-II Breakout Box
PPECB
-
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
Product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
-
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
Product
VME Display And Bus Analyzer Module
VM-DBA
-
VM-DBA is a new test and diagnostic module for VME-bus systems which visualizes activities on all VME bus lines on the set of front-panel LEDs, but also allows one to digitize individual waveforms of all these lines into 2kBit -long storage memories, for a subsequent readout via VME or USB interfaces.
-
Product
Avionics Data Bus Tester
Distributed CORVUS
-
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
Product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
-
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
Product
GPIB-RS232, Instrument Control Device - Taiwan 110VAC
779732-11
-
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
MIL-STD-1553 Simulator & Analyzer Applications Software
F-SIM-1553
-
Avionics Interface Technologies
Software GUI Application for Operating AIT MIL-STD-1553 Interfaces - Bus Monitor Captures & Recordings - Simulate Bus Controller and Remote Terminals (up to 31) - Operate Multiple Bus Channels (and MIL-STD-1553 Modules) Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Engineering Unit Displays & Software Widgets - MIL-STD-1553 A/B Mode Code operations - Also Supports ARINC 429, ARINC 664, Ethernet, & Data Load operations
-
Product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
-
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
Product
PXI Bus Expanders
MXI-4 Series
-
The MXI-4 PXI Bus Expanders allow direct control of PXI systems from any PCI slot in a desktop computer or server. MXI-4 interface cards can also be used to link multiple PXI chassis. MXI-4 technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
Product
PMC ARINC 429 Board
MS 1723
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA and Arinc429 controller based design- 8 transmit and 8 receive independent channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
CZT Gamma-Ray Detector Spectrometer
GR Family
-
The Kromek GR family is a range of CZT-based high-performance gamma-ray spectrometers. They are completely self-contained, with built-in preamplifier, shaping amplifier, baseline restorer, pulse height digitizer, and HV supply. The digitized pulse heights of detected gamma-ray signals are sent to a PC via the USB. The unit is powered entirely from the USB bus, so no external power supply is needed.
-
Product
Super Phosphor Oscilloscopes
SDS2000X-E Series
-
The SDS2000X-E series employs a new generation of SPO technology. With its excellent signal fidelity, background noise is lower than similar products in the industry. It has a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/sec (sequence mode). It also employs a 256-level intensity grading display function and a color temperature display mode not found in other models in this class. Siglent’s newest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering and decoding. History waveform recording and sequential triggering allow for extended waveform records to be captured, stored, and analyzed. Also included is the deep memory FFT. This math function uses upto 1 M samples for the FFT calculation, providing the SDS2000X-E with very high frequency resolution. The hardware co-processor executes true fast measurement and math to all of 28M sample points so that there is minimal distortion on analysis. It also supports searching and navigating, on-screen Bode plot, 16 channel digital /MSO (optional), an external USB powered 25 MHz AWG function generator module (option), a USB WIFI adapter for wireless control and monitoring (option), and an embedded application that allows remote control via web browser. The features and high-performance of the SDS2000X-E oscilloscopes cannot be matched else anywhere at this price.
-
Product
Coaxlink Quad G3 LH
-
Four CoaXPress CXP-6 connections: 2,500 MB/s camera bandwidthPCIe 3.0 (Gen 3) x4 bus: 3,300 MB/s bus bandwidthPassive (fanless) heatsinkFeature-rich set of 20 digital I/O linesExtensive camera control functionsMemento Event Logging Tool
-
Product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
-
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
I2C High Speed Interface for USB
Tracii XL 2.0
-
telos EDV Systementwicklung GmbH
Tracii XL 2.0 is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 3.33 Mbit/s. Additionally Tracii XL 2.0 can work as an I2C monitor.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
I-8000 Parallel Data Acquisition Modules
-
ICP DAS I-8000 Parallel Series I/O are high speed cartridge based and come in a multitude of digital and analog configurations. They are communicable via an RS-485 backplane in all of ICP DAS USA's I-8000 & I-87K series rack mount controllers. There are two types of I/O communication bus, parallel bus and serial bus. The parallel bus type I/O modules (high profile I-8K series) are high speed, used only in the PACs including XPAC, WinPAC, iPAC, ViewPAC, etc. And the serial bus type I/O modules (high profile I-87K series) are low speed, used in both PACs including XPAC, WinPAC, iPAC, ViewPAC, etc.
-
Product
35U (61") non-insulated bus bar
BB-61
-
35U (61") non-insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 4 Bus Matrix Inputs
40-569B-114
-
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-114 is a 8 slot module fitted with 4 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
Bus Analyzer Software
AltaView
-
Alta’s Windows avionics analyzer product, AltaView, provides the most modern technologies for MIL-STD-1553 and ARINC-429 network activity and data analysis. Win XP/Server/7/8/10 Compatible and VMware with ENET/NLINE Ethernet. Ideal for Cybersecurity Testing.
-
Product
PCI Pulse Position Data Communication Board
MS 1708
-
*Bus Interface - PCI Bus*Micro controller Based Design*Shared Memory for Communication*8 Channels RS422 / Modified RS422*PPD (Pulse Position Data) Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS*Independent Intelligent Devices for RS422 and PPT Communication
-
Product
CTEL 6U 16 slot left justfied, P1-2s, P3-5l, with bridge
103CTEL616-9001
-
CompactPCI CTEL 6U 16 slot with system slot left, H110 bus, with bridge, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
Product
Domino Melody
-
One 10-bit 40 MHz A/D converter with one 8- or 10-bit LUT32-bit 33 MHz PCI bus, standard and low profile bracketsD³ technology for extremely low synchronization jitterSupport for mega-pixel progressive-scan and interlaced cameras, asynchronous reset and exposure controlTrigger, strobe and general purpose I/O lines
-
Product
GPIB Interfaces
-
Control older devices that use the ANSI X3.28 protocol from the GPIB Bus. Available in board or rack mountable Minibox™ form.
