-
product
Abrasion/Wear
Our Capabilities*Taber Abrasion*RCA Wear Tester*Resistance to Crocking*Washability*Pencil Hardness*Finish Adhesion
-
product
Reciprocating friction and wear tester.
This testing machine is used to evaluate surface conditions such as friction faces of materials by measuring the frictional force.
-
product
Universal Friction & Wear Testing Machine
Model MMW-1A
Jinan Testing Equipment IE Corporation
The MMW-1A UTM for Friction Wear can simulate rolling, sliding and rolling & sliding combined movement under the certain contact pressure to complete point, line and plane simulating tests. The UTM for Friction Wear can be used to evaluate the friction wear performance of lubricant, metal, plastics, coating, rubber, and ceramics etc. The UTM for Friction Wear can not only satisfy the needs of traditional petrochemical industry to research, develop and inspect the various kinds of intermediate & high grade hydraulic oil, combustion engine oil and gear oil, but also can simulate evaluation on new material development and new technology research under dry condition.
-
product
Uniform Wear Tester
DRK546A
Shandong Drick Instruments Co., Ltd.
Instrument purpose: It is used to evaluate the abrasion resistance of stretchy knitwear.
-
product
Pin-disc Friction & Wear Testing Machine
WPD-2000
Jinan Testing Equipment IE Corporation
WPD-2000 is one type of pin-disc friction wear testing machine. The specimen of metal and non-metal material will be matched to pin shape, disc shape or dual rings to do the test. The pin-disc friction wear testing machine can measure the anti-wear characteristics and frictional coefficient even under lubrication status. WPD-2000 Pin-disc Friction Wear Tester is available in two moods, PC & software mood or non PC mood.
-
product
Wrist Strap and Foot Wear Testers
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
product
Friction & Wear Testing Machine
Jinan Scientific Test Technology Co. LTD.
Friction & Wear Testing Machine
-
product
Bearing friction and wear tester
This testing machine evaluates the frictional characteristics of radial bearings. The circuit system adopted for the lubricant enables heating up to 80C.
-
product
Conventional friction and wear tester
EFM-III
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
product
Tribometers/Abrasion Testers
AEP Technology offers several ASTM, ISO DIN compliant friction and wear tester models optimized for various applications. The modular design allows it to run on one platform (rotary, linear reciprocating, linear, block-to-ring, etc.), and to ensure high repeatability, during the testing process our downward force friction and wear testing machine controls several standard tests. High-end electronics, multi-core 64-bit processor that allows it to use multiple in-situ sensing technologies (recording friction, wear, displacement, force, volume, temperature, humidity, position, speed, etc., during testing) with high resolution Embedded powerful platform imaging head (sections of atomic force microscopes, etc.). Ease of use and robust unique design make AEP Technology a powerful tool in friction and wear testing machine development and production environments.
-
product
Medical Masks Flammability Tester
TF361
TESTEX Testing Equipment Systems Ltd.
Medical Masks Flammability Tester is used to test the flammability of medical masks, to ensure the safety of masks to wear in. Medical Masks Flammability test Chamber complies with EN 149, GB 2626, GB 19083.
-
product
High-pressure environmental friction and wear tester
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy.
-
product
Turbine Flow Meters
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
product
On-site Oil Analyzer
MicroLab 30
MicroLab 30 is designed for fleets operating over-the-road vehicles or generator equipment. This analyzer best suited for companies interested in testing primarily engine oils to determine the serviceable life of the oil and the equipment condition. The MicroLab 30 analyzes six oil chemistry parameters along with viscosity to determine proper drain intervals. The standard 10 element version provides information on oil contamination and wear metal analysis to determine if mechanical issues exist. The MicroLab 30 can be upgraded to 20 elements if there is an interest to analyze oil additive levels as well as additional wear metals.
-
product
Textile Testing Equipment
Dongguan Kejian Instrument Co., Ltd.
Used for testing the performance of the wearing resistance,abrasion, appearance change (pilling degree/class) of the textiles and membrane materials.
-
product
Arresters
Next to your people, your power grid infrastructure is your largest and most valuable investment. Protect it with Hubbell Power Systems, Inc. surge arresters. Every lightning strike, insulator flashover and switching surge adds wear and tear to your equipment, prematurely aging it, and requiring you to shoulder the costs of replacement. Even the smallest surge can shorten your equipment’s life. Surge arresters, however, extend the life of your system by limiting the voltage across your equipment during a surge event.
-
product
Wear Testing Machine
M-2000
Jinan Testing Equipment IE Corporation
Model M-2000 Wear Testing Machine is to be used test the anti-wear performance for metal and non-metal specimen under the sliding, rolling, and sliding-rolling condition. The Wear Testing Machine can also test various materials under dry-friction and wet-friction. The wear testing system can calculate friction work & friction coefficient by the data acquired. The Wear Testing Machine is widely used in universities, research & scientific institutes.
-
product
Real-time Lubricant Analyzer
RT-Lube
Instrument platform that is capable of real time, on site detection of wear elements in lubricating fluids. Currently the process to test lubricants is to take a manual sample for lab testing. This approach is expensive, labor intensive and time consuming. The RT-Lube Analyzer can replace this manual approach by automatically sampling, on a pre-scheduled basis, the fluid under consideration. The analysis is immediate and is communicated back to cloud based storage systems where the analytics can take place.
-
product
Water Vapour Permeability Tester
TESTEX Testing Equipment Systems Ltd.
Water Vapour Permeability Tester, to determine the resistance of textiles and textile composites (particularly action wear fabrics) to water vapour penetration. Water Vapour Permeability Tester complies with BS 3424/7209, etc.
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
PXI Solid State Very High Density Matrix
40-501-001
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
product
Ferrous Wear Metal Measurement In Lubricants
FerroCheck 2000 Series
The FerroCheck 2000 Series of portable ferrous analyzers offer accuracy and convenience for total ferrous measurement of in-service lubricating oil and grease. Fast and easy to use samples are analyzed in less than 30 seconds. Small sample volumes of just 1.5 ml of oil or 0.75 ml of grease are needed to measure ferrous content in part per million (ppm) by weight. The FerroCheck measures the total ferrous content of both small particles from normal machine wear and large abnormal wear particles.
-
product
PXI Solid State MUX, 1 bank, 160 channel
40-680-006
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Roughness Testers
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
product
PXI/PXIe RF Multiplexer, Triple 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-003
This multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
Power Circulation Type Tire Wear Tester
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
product
Safety Voltage Detector
289 SVD
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● Mute function● AC voltage detection: 100Vac ~ 69kVac● Frequency range: 50/60Hz● Easy-to-prove method● Self-test function● Power source: 1.5V(AA) alkaline battery × 3● Non-contact detection by proximity● Personal sensor, easy to wear and convenient to use● Can be attached with hot sticks by optional accessory● Lightweight, robust and compact● Easy access to batteries Comply with EN 61326-1
-
product
Tribocorrosion Tester
ASTM G119
Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.
-
product
RF Safety Monitoring
MVG EME Guard Plus
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
