Automated Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance.
See Also: ATE
-
product
Motorised and Automated Probe Heads
Motorised heads enable automated, repeatable re-orientation of probes to allow access to features on all faces of the part, improving the capability of the CMM and maximising productivity.
-
product
Automated Chemistry Analyzers
OI Analytical''s automated chemistry analyzers provide precise, accurate, and rapid results using multichannel continuous flow technology.
-
product
Automated Thermostat Test System
*Transport mechanism moves thermostats to various temperature controlled locations.*Continuously monitored process status*PC controlled transport and measurements*Operator is shielded from 200 - 210 degree F hot water insertion baths*LabVIEW® test/process language
-
product
Multifunctional Safety Tests
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
product
Microwave Testing
140
The PICOPROBE® MODEL 140, a high performance microwave probe which incorporates a WR-8 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
product
Network Performance Testing
From homes and offices through to production plants: everyone is looking at network service providers and equipment manufacturers to ensure outstanding network performance for work and play. Yet, what is ‘outstanding’ network performance’ all about?
-
product
In-Circuit Testing and Test Engineering
Teradyne Z1890
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
product
Automating Captioning Workflows
BATON® Captions
BATON® Captions is an automated solution for all kinds of captioning needs, allowing broadcasters and media professionals to address requirements from caption generation to QC, auto corrections, review, and editing. Leveraging cutting-edge machine learning (ML) and automatic speech recognition technology, BATON Captions brings simplicity and cost savings to the creation, management, and delivery of captions for traditional TV and video streaming.
-
product
Pharmaceutical Climate Test
CP series
Our Pharmaprfschrnke have been specifically designed for long-term and stability testing in the pharmaceutical industry and have very small tolerances. With these test chambers can be the shelf life of different products such as check medicines and identify suggestions for optimal storage conditions.
-
product
Twin columns automated force test stand 36" travel - 2000lb
702SN
The advanced 702SN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
RFID Test Instrument
RAIN Xplorer
The CISC RAIN Xplorer is a unique RFID test product developed for convenient tag frequency sensitivity, communication range, and backscatter measurements. The RFID tester is designed for open area tests and measurements in an RF-controlled environment using portable or fixed RF test chambers. The system is supplied with software and a reference tag for self-calibration.
-
product
Test Connectors
The need for contacting standard USB or RJ connections and interfaces is increasing in the field of in-circuit and functional tests of PCBs because the standardization of these interfaces has great advantages.
-
product
RF Shielded Test Enclosure, for Laptop Testing
JRE 2218
Breeze through laptop RFI and wireless tests with the 'bigger than-a-breadbox' 2218! Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan.
-
product
Automation OT Application Platform
Schweitzer Engineering Laboratories, Inc.
The SEL Blueframe application platform and its enabled applications help you maximize the use of system data and provide you with a scalable and customizable solution that accommodates your system schemes today and in the future.
-
product
Compliance Testing Services
We offer testing for compliance across many of the standard specifications. Austin Labs also creates custom conformance programs for many of our partners to help them address gaps in testing coverage. These compliance capabilities include full automation of tests suites to allow for standardized pass/fail testing.
-
product
Flow Leak Testing
Leakmaster UltraFlow v3
NEW AND IMPROVED EtherNet/IP FEATURING "SLAVE MODE". PROGRAMMABLE ELECTRONIC PRESSURE REGULATOR . DIGITAL MASS FLOW SENSOR WITH BROAD TESTING RANGE . LED STATUS INDICATOR. DUAL ACCESS DOORS FOR FLEXIBLE MOUNTING
-
product
Telecom Test Systems
4301 Series
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
product
Testing and Measurement
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
product
Radio Test Set
CMA180
With its frequency range from 100 kHz to 3 GHz, the R&S®CMA180 is ideal for testing all common analog and digital radio systems. Input levels up to 150 W are no problem for the R&S®CMA180. The flexible internal switching capabilities for the audio and RF paths make the R&S®CMA180 suitable for a wide range of test requirements. Users can configure the internal generators, external audio sources, filters and measurements according to the given application. In the predefined test scenarios for receiver, transmitter and duplex tests, the RF and audio paths are preconfigured. This saves time and eliminates configuration errors for standard test cases.
-
product
Test Tool
Iron - IEC 60870-6
Iron is a Windows™ application that creates compliant IEC 60870-6 (TASE.2/ICCP) Applications, both unidirectional and bidirectional. Iron is a highly configurable tool with multiple simulation options for changing Data Model values and generating valid message traffic. Support for Read, Write, Reporting, Discovery, Controls, and Dynamic DataSets are built into the tool.
-
product
Off-line Automated Liquid Handling Station
SimPrep
- Wide range of syringes from 10 μL to 50 mL- A single system can serve multiple techniques such as ICP-MS, ICP, AA, Colorimeter, IC, FIA- An extra autosampler - easily switch between sample prep and sample analysis with a switching USB hub (see below).
-
product
Universal Testing Machine
A Universal Testing machine, also known as universal tester, materials testing machine, is used to test the tensile strength and compressive strength of materials. It is named after the fact that it can perform many standard tensile and compression tests on materials, components and structures. Along with these, there are many more capabilities of this testing machine. There are variety of terms in the industry that are used to refer to a UTM. Most common are “tensile tester”, “compression tester” and “bend tester”. An earlier name for a tensile testing machine is a Tensometer. It is used to play out the numerous tractable pressure and compressive quality of materials or parts.
-
product
Test Automation Services
Paragon Systems has experienced mechanical designers on staff who have developed many custom automated test equipment in SolidWorks. We will work with the customers in very close relationship from the beginning of the project to the end.
-
product
SNMP Test Suite
SilverCreek
SilverCreek is the Authoritative SNMP Test Suite -- designed to test implementations of the Simple Network Management Protocol (SNMP agents) and standard and private MIBs (Management Information Bases). SilverCreek incorporates thousands of small, single function tests written in the Tcl scripting language to exercise one or a small number of parameters. The syntactic tests verify protocol compliance, error and exception handling, and boundary condition behavior. The functionality tests (semantic tests) verify performance, trap/alert/event/notification handling, counter accuracy, security, and many other implementation specific areas.
-
product
Microwave Testing
170
The PICOPROBE® MODEL 170, a high performance microwave probe which incorporates a WR-6 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
product
Security Policy Change Automation
FireFlow
Confidently automate your security policy change process - from planning through risk analysis, implementation and validation.
-
product
Test Switches and Accessories
Test switches are designed and manufactured to allow quick and easy multi-circuit testing of switchboard relays, meters and instruments by any conventional system.These test switches and related test plugs have the features necessary for applications involving the measurement of individual currents and voltages associated with substation instrumentation and protection devices. They have been especially designed for the measurement of potential elements, current elements, and make-before-break short-circuit elements related to Current Transformer (CT) circuits.
-
product
Microwave Testing
50A
The GGB Industries, Inc., MODEL 50A probe sets new standards in microwave probing performance. Using low loss coaxial techniques, the Model 50A achieves an insertion loss of less than 1.0 db and a return loss of greater than 18 db through 50 GHz.
-
product
Automated Data Testing Solution
QuerySurge
Real-Time Technology Solutions, Inc.
QuerySurge is RTTS’ smart Data Testing solution for Big Data that finds bad data & provides a holistic view of your data’s health. QuerySurge helps your team coordinate your data testing initiatives while speeding up your development & testing cycles and finding your bad data.
-
product
Hardness Testing
Wilson® hardness testers include a comprehensive range of hardness testers from Rockwell®, Knoop/Vickers, and Brinell to fully automatic production systems. Our hardness testers are complemented by a range of ISO test blocks, accessories, and fixtures. Our calibration laboratory is recognized as the global leader in the production of premium ISO test blocks and indenters.
