Battery Internal Resistance Testers
See Also: Resistance Test, Battery Conductance Testers
-
Product
Insulation Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Testing the integrity of insulation requires measuring its resistance to current flow across it. A high level of resistance means that very little current is escaping through the insulation. Conversely, a low level of resistance indicates a significant amount of current may be leaking through and along the insulation.
-
Product
High-voltage Testers
-
Operational safety and reliability of electrical equipment and cables directly depend on the dielectric strength of the insulation. Portable and mobile high-voltage testers from KharkovenErgoPribor Ltd. are used for acceptance and operational testing of substation equipment and cable lines, as well as for checking the reliability of personal electrical safety equipment. Our testers range is represented by test systems that allow conducting high-voltage tests with DC and AC voltage, testing polymer insulated cables with very low frequency, testing and locating faults in cable sheath, as well as performing the initial burning of insulation on damaged sections of cable lines.
-
Product
Low Resistance Metal Film Chip Resistor
RTX
-
This specification is applicable to lead and halogen free RTX series low resistance metal film chip resistors. Lead free products mean lead free termination meets RoHS requirement.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
Internal Vapor Analyzer
IVA® MODEL 210S
-
The IVA® system is specifically designed for the quantitative analysis of low molecular weight gases contained in hermetic packages, cavities and other enclosures. The Model 210s concept integrates automated hardware with easy-to-use icon-driven software. Its design permits routine quality control, failure analysis and research level testing operation as a turn-key analytical system. The IVA® Model 210s includes a high-performance, quadrupole-mass spectrometer analyzer, a sample-mounting interface and precision hardware. The instrument is also computer-controlled and equipped with exclusive ORS integrated system control software — which provides instrument control, data analysis, data archiving and ease of operation.
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
Specialty Testers
-
Test Products International, Inc.
TPI specialty testers offer versatility and precision to meet the needs of a variety of jobs and projects.
-
Product
Polarization Tester
-
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
Product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
-
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
Product
Phasing Tester
-
Phasing testers are used on grounded and ungrounded alternating current systems to check high-voltage fuses, test for correct phase connections and test for the absence of high voltage on de-energized lines or apparatus.
-
Product
Battery Testing Systems
-
The CT2001 series Battery Testing Systems are designed for energy storage materials research and battery test. The eight channels are independently programmed and controlled by the computer. The Current ranges are from 1 mA to 5 A and Voltage ranges from 2V to 15V. Each testing system is specifically built for customer needs.
-
Product
TRA-300 LED Thermal Resistance Structure Analyzer
-
Hangzhou Everfine Photo-E-Info Co., LTD
The TRA-300 accurately measures the thermal resistance, junction temperature, optical power, voltage, current and other parameters of LED packaging products.The heating and cooling curves of LED can also be obtained, and the integral and differential thermal structure functions can be obtained by establishing the finite element model.Through the structural function analysis of the TRA-300 special software, the fine thermal resistance structure of the LED (from the chip to the thermal resistance value of each package structure) can be obtained, so as to objectively evaluate the heat dissipation quality and thermal management level of the LED package products, and provide the best verification for the heat dissipation design of the LED.
-
Product
Hardness Tester
NB3010 Series
-
Newage Testing Instruments, Inc.
A basic Brinell hardness tester with semi-automatic operation. NB3010 is a cost-effective Brinell tester using deadweights with a pneumatic load system to apply and remove the loads. Operates in most all Brinell scales.
-
Product
Circuit Tester
69105
-
Tests circuits rated from 80 to 600 volts AC/DC.High-visibility neon lamp indicator.High-impact, sealed 5-11/16'' (144 mm) probes on long 24'' (610 mm) leads for convenience in testing motors, fuses, relays, switches, etc.Resistor between each probe and lead.Reliable electronic components.
-
Product
Environmental Testers
-
AEMC manufactures a line of cost effective, hand-held instruments for measuring temperature, humidity, light, wind speed and other variables. Each instrument in this series includes sensor, backlit CD and a shockproof holster. They are battery operated and can easily be carried in a shirt pocket.
-
Product
Motor Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
Product
Cellular Tester
IQxstream-5G
-
This high performance, comprehensive non-signaling tester is ideal for both 5G user equipment (UE) & small cell testing across multiple cellular technologies including 2G, 3G, 4G & 5G.
-
Product
Low Resistance Ohmmeters
-
Some times know as Ducter testers, these are highly accurate, easy to operate instruments that measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
Product
Battery Chargers
-
The JUNXY intelligent battery charger covers three charging processes: (1)Constant current charging → (2)Constant voltage with decreasing current charging→ (3)micro current floating charging. Auto shut-down when reach any one of four charge cutt-off settings: (1)cell voltage, (2)charge duration, (3)charge capacity, (4)manual stop charge. It is especially designed for battery bank maintenance for different industries with nominal voltages: 24V, 36V, 48V, 80V, 96V, 110V/120V, 220V/240V, 380V etc with different charging current.
-
Product
Insulation Resistance Meter
AMIC-10k1
-
Insulation resistance measurement - 40TΩ: * 50 - 1000 V, in 25 V steps, * 1000 - 10000 V, in 50 V steps ; Memory, bluetooth keyboard option, heating location ; Measurement of AC and DC voltage and capacity ; Measurement of leakage current and function with digital filter ; Measurement of continuity of protection and equipotential connections ; Adjustable alarm limits.
-
Product
Automated Testers
-
Automated test equipment creates a repeatable and efficient environment for testing your products. Innovar offers modular test equipment that easily scales with your production demands and provides redundancy to ensure continued production.
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Xenon Lamp Weather Resistance Test Chamber
-
SN Xenon lamp test chamber adopts the Xenon ARC lamp that can simulate full sunlight spectrum to reproduce destructive light waves existing in different environments so as to provide the corresponding environment simulation and acceleration test for scientific research, product development and quality control.
-
Product
Installation Testers
-
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
Product
Resistivity Meter
-
Integrated Geo Instruments & Services Private Limited
The instrument design incorporates several advanced techniques of digital circuitry to make it reliable Geophysical tool that provides high quality data useful for all types of mineral and groundwater exploration research etc. The SSR-MP1 sends the entire current into the ground without wasting power for constant current generation thus increasing the signal strength to probe deeper layers.
-
Product
2-Channel Resistivity Meter
HE-960RW-GC(W)
-
The HE-960RW-GC(W) is a 2-channel simultaneous-measurement carbon sensor, resistivity meter that can be connected with two sensors. The measurement range is: 0 - 100.0 MΩ・cm.The high performance and high precision is maintained while simultaneously measuring the output of the resistivity of different two locations. This is carried out in a single converter for overall cost efficient performance.
-
Product
Battery Charger Meters
-
A range of ammeters and voltmeters with tough moving magnet or polarised moving iron movements designed for low cost indication of d.c. or rectified a.c.





























