Resistance Test
measured in ohms is the ability of a current to conduct.
See Also: Resistance, Resistivity, Resistance Standards, Resistance Meters, Battery Internal Resistance Testers
-
Product
Tire Rolling Resistance Test System
-
This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.
-
Product
Low Resistance Test System
9100-2
-
Palico Instrument Laboratories
The Model 9100-2 measures the resistance of single or multiple battery separators quickly and accurately when used with our Model 9000-9100 Electrolyte Test Bath. This system uses a 4-terminal measurement technique which cancels the effects of electrode/electrolyte potentials.
-
Product
Xenon Lamp Weather Resistance Test Chamber
-
SN Xenon lamp test chamber adopts the Xenon ARC lamp that can simulate full sunlight spectrum to reproduce destructive light waves existing in different environments so as to provide the corresponding environment simulation and acceleration test for scientific research, product development and quality control.
-
Product
UV Weather Resistance Test Chamber
-
This series is applicable for the sunlight resistant test of nonmetallic materials and aging test of artificial light source.
-
Product
Digital Surface Resistance Test Kit
PAS-853BRM
-
- Surface Resistance Kit from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period control- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and point-to-ground (Rtg)- Measures resistance of Static Control Floors, ESD Work Surfaces and Packaging Material- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Conductive Rubber Electrodes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included
-
Product
Insulation Resistance Test Instrument
2681
-
Shenzhen Chuangxin Instruments Co., Ltd.
Insulation Resistance Test Instrument
-
Product
test measurement unit
ITC59100 Rg/Qg
-
The ITC59100 Test Measurement Unit (TMU), which plugs into the ITC59000 Test Platform, performs gate charge (Qg) measurements that conform to MIL-STD-750C, Notice 2, Method 3471 and JEDEC Standard JESD24-2. In addition the ITC59100 TMU performs an internal gate resistance (Rg) test method that conforms to JEDEC Standard JESD24-11.
-
Product
Insulation Resistance Measurement
MI15KVe
-
The MI-15KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15kV.
-
Product
Safety Test Panel for Geyser
-
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
Product
Mini Digital Multimeter
HH2103
-
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection
-
Product
Resistivity Test System
RMS-1000
-
Accurate and powerful performance. - Possible to get much accurate resistivity value by taking 8 raw data. - Good to check ohmic contact by flowing forward and reverse current.2. We provide various sample mounting board and probe head and tips.3. We have an optional item which can measure in variable temperature. - Room Temperature ~ 300dC.
-
Product
Environmental Test Chamber
-
Test Chambers are used widely in temperature variation tests, cold resistance tests, and for low-temperature storage in the areas of aerospace and aviation, electronic instruments, electrical products, materials, parts, and components.
-
Product
Hand-In Type Electromagnetic Anechoic Box (Shield Box)
MY3710HS
-
Higher shielding performance than MY371080dB. Suitable for weak electric field resistance test, out-of-service test or digital forensics for mobile phone, smart phone or tablet terminal! DUT can be operated directly with bare hands while placing it in the box and looking at the inside from the shield window.
-
Product
Insulation Resistance Measurement
MI20KVe
-
The MI-20KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV.
-
Product
Resistive Current Tester
-
Weshine Electric Manufacturing Co., Ltd
Long Distance Digital Zinc Oxide Arrester Resistive Current Safety Testing Set
-
Product
Leak Tester
LSD-01A
-
Jinan Leading Instruments Co., Ltd.
LSD-01A Leak Tester is applicablein leak testing of pouches, bottles, pipes, cans and boxes of foodstuff,pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It’ s also applicable in the leak testing ofthe specimens after falling tests and pressure resistance tests.
-
Product
Digital Clamp Tester (CE)
M-2100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Conform to IEC safety requirements.
-
Product
Jumbo LCD Digital Multimeter
HH2102A
-
Basic Accuracy 1.0%. Jumbo LCD display 2000 count, 21mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 20MΩ. Signal injection and Diode test
-
Product
EBIRST 104-pin D-type Verification Fixture
93-022-101
Verification Fixture
The 93-022-101 104-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
-
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables automated test mode, where the instrument operates the tap changer without operator input and records winding resistance results based on pre-selected stabilization criteria. This option makes the operator’s job significantly easier.Both models can output test currents from 5 mA to 25 A DC for the purpose of winding resistance measurement. TWA40D has a special test mode for checking the synchronization of on-load tap changers with three phases simultaneously tested in parallel, in which the total test current can rise to up to 40 A DC.TWA40D has additional advantages when it comes to non-intrusive tap changer analysis. The unique DVtest method enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, simultaneously with the measurement of tap changer motor current which helps with the detection of motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or on three phases simultaneously. It can also be performed as an additional test simultaneously with the winding resistance test in all tap positions.An additional unique advantage of TWA40D is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer (connected in a YN configuration). This can significantly shorten the total testing time – for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.The test leads for TWA three-phase transformer winding ohmmeters are interchangeable with the TRT turns ratio testers, which means that both sets of tests can be performed with a single test lead connection to the power transformer terminals.
-
Product
Multi-Test Resistivity Measurement System
-
Sheet resistance mapping of thin films with a collinear 4-point probe, Temperature co-efficient of resistance (TCR) of thin films with collinear 4-point probe, Precision temperature co-efficient of resistance (TCR) with 2-point Kelvin probes and precision surface temperature probe, resistor testing with 2-point Kelvin probes,Precision resistor testing with a Kelvin probe card, temperature co-efficient of resistance resistor test (TCR), and Standard TCR test of multiple resistors with Kelvin probes or a probe card.
-
Product
RUB-01
Rub Tester
-
Jinan Leading Instruments Co., Ltd.
RUB-01 Rub Testerisapplicable in abrasion resistance test of printing works, light sensitive layer of PS boards, and coating layers of relative products. It can help users toanalyze the affairs of lower abrasion assistance, ink layer falling-off, lowerprintable of PS boards, and rigid of coating layers of other products.
-
Product
Digital Igniter Tester
Alpha 4314
-
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
Product
EBIRST 23 X SMB Verification Fixture
93-011-101
Verification Fixture
The 93-011-101 23 x SMB Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Safety Testing Equipment
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD provides safety testing solutions and safety testing equipment, including UL1439 Sharp Edge Tester, Range Hood Air Volume Measurement Test Device, Spring Impact Hammer Calibration Equipment, Scratch Resistance Test Machine, Adjustable Universal Energy Spring Impact Hammer, IK Vertical Hammer Impact Tester. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Combination Measuring Devices According to DIN EN 61557-10 (VDE 0413-10) are permitted
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
Product
Standard 1.08 (31.00) - 3.50 (99.00) General Purpose Probe
EPA-2C40
General Purpose Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35 Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
EBIRST 78-pin D-type Test Tool
93-006-001
-
The 93-006-001 eBIRST 78-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Installation Safety Testers
VDE 0100
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
Product
Dry Arc Resistance Tester
-
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
