Fault Location
Determine the location of faults.
-
Product
Vector Network Analyzer 9KHz-3.2GHz. Includes Adv Meas Kit, Distance To Fault Opt, Cal and Utl Kits
T3VNA3200
Vector Network Analyzer
Vector Network Analyzer 9KHz-3.2GHz. Includes Adv Meas Kit, Distance To Fault Opt, Cal and Utl Kits.
-
Product
Pre- Locator
CFL PL3
-
CFL PL3, new generation Cable Fault Pre-Locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault with accuracy.
-
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Partial Discharge Expert Diagnostic and Location System
PDExpert
-
Power Monitoring and Diagnostic Technology Ltd.
The PDExpert is PMDT's third level of Partial Discharge (PD) Expert Diagnostic and Location System. It is a powerful, portable, multi-channel system of impeccable design used to analyze and pinpoint PD signals coming from a power asset within centimeters while the power system is energized. The system consists of UHF, AE, HFCT and ultrasonic sensors, one advanced UHF/PD signal processing unit, one oscilloscope, filters and other accessories.The system employs ultra-high speed data acquisition and advanced digital signal processing technologies, compares the UHF, AE and HFCT signals of different frequency ranges to determine if it is PD or noise, and locates the source in power assets accurately by utilizing Acoustic-Electromagnetic Combination Location Technique, time Difference of Signals' Arrivals (TDOA), and 3D Positioning Technology.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-193A-001
Fault Insertion Unit
The 40-193A-001 is a 7-Channel Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
-
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
Product
Cable Locating Device
TM520
-
Coordinating with high-voltage signal generator, test sound and magnet simultaneously, locate high-resistance and arc-over fault of the power cable. While fixing the fault point, the instrument can test the cable path as well.Coordinating with audio-frequency signal generator, test audio frequency induction, locate low-resistance fault, and identify the cable and test the depth of it.
-
Product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
-
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
PXI Fault Insertion Matrix Modules
-
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
Short-circuit and Earth Fault Indicators
-
The Sensorform range of Short-circuit and Earth Fault Indicators detects short-circuit and earth faults on medium voltage underground cables. A wide range of options are available for enclosure type, power source, indicator type, reset method, trip-level selection, auxiliary outputs, and remote indication.
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Cable Locator (LCD type)
5500 CB
-
Standard Electric Works Co., Ltd
● The 5500 CB transmitter is a great tool for locating and identifying cables and individual conductors. ● Designed for locating unenergized cables and powered cables. ● Voltage measurement for cables : ACV 12V~300V DCV 12V~300V ● Signal Transmission • Transmission Power Level Selection (includes 1, 2, 3) • Transmission Signal Code Selection (includes F, E, H, d, L, C, O, A) ● Flashlight & Back Light function.● The Silent Mode (Disable Button Beep).● The Level Bar Display on the LCD Screen (the transmission power level indication).● The Action Wave Display on the LCD Screen (when the signal is transmitted).● Auto power off function.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2310
-
CableTroll 2310 is an indicator for detection of earth faults (PtG) on multi-core and single core cable terminations. The unit uses NorTroll type current sensor (CT)
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
Product
Fault Indicators and Sensors
-
Schweitzer Engineering Laboratories, Inc.
This technology detects overcurrent faults on overhead and underground lines to speed up power restoration and enhance protection.
-
Product
Locate and Map Underground Utilities
UtilityScan DF
-
Geophysical Survey Systems, Inc.
UtilityScan DF incorporates our innovative dual-frequency digital antenna (300 and 800 MHz) and an easy-to-use touchscreen interface to view shallow and deep targets simultaneously in a single scan.
-
Product
PVC Pipe Locators
-
The All-New AML PRO™ is a scientific instrument that utilizes ultra-high radio frequencies to find differences in densities. This offers the best method for locating PVC & PE pipes and nearly any other object that has an edge.
-
Product
Cable Fault Finder
-
Techno Instrumentation (India) Private Limited
Magnetic and Acoustic signal strength through bar graph and digits on LCD.Coincidence feature gives distance to the fault in milliseconds.Easy, fast and accurate pinpointing of faults.
