Fault Location
Determine the location of faults.
-
Product
Tool, Crimp, TriPaddle (10 amp), Thermocouple, Micro Power, Receiver and ITA , Locator Required
910101102
Crimp Tool
This crimp tool can be used to crimp 10 Amp TriPaddle contacts, Thermocouple contacts or Micro Power contacts. Locator required.
-
-
Product
Ground Fault Monitors
IFT
-
In most industrial settings, ground faults can cause significant damage. Since these leaks are unavoidable in almost all industrial environments, our ground fault monitors allow you to quickly and easily find the source of the leak before a major problem occurs and damages your equipment. The IFT-120 is designed to help you rapidly locate ground faults.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Ground Fault Monitor
IFT-120
-
Our ground fault monitors enable you to easily and quickly find the source of the fault before a major problem occurs and damages your equipment. This is the IFT-120, designed to assist you in rapid identification of ground faults.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
42-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
Electrical Fault Detector
-
Our product range includes a wide range of Electrical Fault Detector and 0.36W Electric Fault Detector.
-
Product
Hazardous Location Syringe Pump
1000HLf
-
The Teledyne ISCO HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
5mA High Accuracy Ground Fault Detector
HA-GFD
-
Our HA-GFD Current Probe is our most sensitive current probe, measuring down to 5 milliamps. Ideal for measuring leakage current and ground faults. Dual range allows measuring up to 200 amps in high accuracy.
-
Product
Cable Locators
-
We have cable length meters, locators and fuse finders for electrical, data network and telecommunication applications.
-
Product
Cable Locators & Testers
-
PeakTech Prüf- und Messtechnik GmbH
This new cable detector consisting of a transmitter and a receiver is suitable for the search of voltage-free and voltage - carrying lines, as well as line interruptions and line tracking of surface and flush-mounted lines, pipe systems and even lines in the ground.
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Utility Locator
VM-850
-
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-850 operates at a much lower frequency of 9.82kHz which is ideal for smaller diameter utilities such as CATV, power and telephone with less bleeding onto adjacent services.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Cable Locators, Route Tracers And Height Meters
-
CHM cable height meters are easy to use, handheld devices which use ultrasound to determine the height of up to six overhead cables and wires. They are designed to measure cable sag, overhead clearance and cable heights up to 23 m, with separate products dedicated to the power and telecommunications markets. As a safe alternative to telescopic ranging sticks, there is no physical connection to the cables.
-
Product
Partial Discharge Expert Diagnostic and Location System
PDExpert
-
Power Monitoring and Diagnostic Technology Ltd.
The PDExpert is PMDT's third level of Partial Discharge (PD) Expert Diagnostic and Location System. It is a powerful, portable, multi-channel system of impeccable design used to analyze and pinpoint PD signals coming from a power asset within centimeters while the power system is energized. The system consists of UHF, AE, HFCT and ultrasonic sensors, one advanced UHF/PD signal processing unit, one oscilloscope, filters and other accessories.The system employs ultra-high speed data acquisition and advanced digital signal processing technologies, compares the UHF, AE and HFCT signals of different frequency ranges to determine if it is PD or noise, and locates the source in power assets accurately by utilizing Acoustic-Electromagnetic Combination Location Technique, time Difference of Signals' Arrivals (TDOA), and 3D Positioning Technology.
-
Product
PD Pipe & Cable Locator
PD / PD-H
-
Audio frequency 750cpsMaximum 100v outputFine Tune knob and LED's to easily match maximum impedanceInterrupter feature on oscillatorLCD meter on receiverReceiver loud speaker or headset useHoliday detection on buried pipe (PD/H)
-
Product
Ground Fault Detectors
-
STB Electrical Test Equipment, Inc
STB's convenient Ground Fault Detectors may be operated with one hand and are ideal for preventative maintenance. Ground Fault Detectors indicate ground faults and electrical leakage while equipment is in operation.
-
Product
Metal Box Locator
P500
-
Although originally designed to accurately locate valve boxes and manhole covers, the Elcometer P500 Metal Box Locator can also be used as a general metal detector.
-
Product
PXI Fault Insertion Insertion Switch Modules
-
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
Switch Module
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Noise Location Package
Type HFDF
-
National RF’s Type HFDF high frequency location system is a proven noise hunting and location directional antenna system that allows you, in many cases, to walk right up to the source of High Frequency (HF) noise! Used by several power companies around the United States, professional noise hunters, and other communications specialists, the HFDF has located noise sources that emanated from pole power transformers, arcing electric fences, CATV in-line amplifiers, plasma TV screens, and even Marijuana grower’s heating lamps! The system incorporates several plug-in, tunable magnetic loop sensors of a proprietary National RF design, that cover the frequency range between 1.8 MHz and 55 MHz. The unit is packaged in a hand-held, lightweight metallic enclosure, with a pistol grip and a magnetic compass mounted on top. The compass is used to get magnetic bearings to the noise source, which may be plotted on a map to triangulate, and ultimately pin-point, the location of the noise source. In certain cases, our customers tell us that they have been able to walk right up to the interfering noise source and correct the situation on the spot!
-
Product
Static Locator
983v2
-
The Model 983v2 Static Locator provides accurate measurement of electrostatic charges. Its design enables fast response, low drift and ease of operation. The 983v2 can operate in ?Continuous? or ?Peak Hold? mode to record changes in the level of charge or the highest charge detected respectively.
-
Product
Fault Indicators and Sensors
-
Schweitzer Engineering Laboratories, Inc.
This technology detects overcurrent faults on overhead and underground lines to speed up power restoration and enhance protection.
-
Product
Acoustic Fault Detector
AFL212-AMD
-
K&S Engineering and Scientific Ltd
This compact acoustic headset, designed and manufactured by K&S Engineering and Scientific Ltd has been developed with state-of-the-art components to not only to achieve superior performance but also to offer the user an acoustic headset that is smaller than equivalent units currently available on the market. Housed in an IP67 enclosure, the unit, which is used in conjunction with a high voltage surge generator, can easily contend with wet conditions.
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch
40-190B-002
Fault Insertion Unit
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Non-metallic Pipe Locator
NPL-100
-
The NPL-100 is a sophisticated instrument for locating non-metallic water pipelines.Using a vibrator attached to the outlet of a fire hydrant or to pipe fittings, the NPL-100 sends a sound wave through the water in the pipe.
-
Product
Tool, Locator, Thermocouple, Receiver
910104134
Locator Tool
Used with Crimp Tool Part # 910101102 to crimp thermocouple receiver contacts.
