Burn-In
The application of current, typically at high temperatures, over periods of time to detect infant mortality.
See Also: Burn-In Boards, High Power Burn-in, Burn-In Sockets, PCB Inspection
-
Product
Glow Wire Tester
-
Shanghai Dean Electrical Co., Ltd
Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.
-
Product
AFC 45° Automatic Flammability Tester
M233G
-
To determine the burning characteristics of textiles under controlled conditions. Stainless steel test cabinet with glass observation panel provided with automatic timing of flame spread in 0.1 second increments from ignition.
-
-
Product
Horizontal Flammability Tester
-
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
Product
6 Chip Detection and Burn Channels
CD1
-
The CD1 provides 6 Chip Detect and Fuzz Burn interface(s). A Chip Detector (CD) is a magnetic-electrical device that provides a reliable method of detecting impending failure of bearings and gears.
-
Product
IC Test Services
-
With knowledge gathered from decades of supporting Tier 1 and emerging industry leaders, Amkor understands test solutions must address advanced technology, quality, performance and cost of test. We offer full turnkey solutions including wafer processing, advanced bump, wafer probe, assembly, final test, system-level test, burn-in and end-of-line services.
-
Product
Test House Services
-
Microtest provides complete test house services in a clear room equipped with the state of the art handler and wafer probing system using its own innovative ATE.The test house operates in hot, cold and room temperature for both production and characterization test.Innovative reliability system for Burn In and HTOL ServicesStatistical analysis is performed for digital and mixed-signal devices.Microtest Pacific Test house is located in Malacca (Malaysia).
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
Cloud And Networking
-
From laser chips (EMLs, DMLs, and VCSELs) and pluggable coherent transceivers to pump lasers and TrueFlex® colorless/directionless/contentionless ROADMs, Lumentum’s comprehensive, vertically integrated portfolio lowers costs and speeds time-to-market. We optimize our components for best-in-class performance, creating flexible and scalable platforms that address ever-changing market conditions and product migrations. To ensure field reliability, Lumentum uses only the best materials and processes including stringent, proprietary burn-in processes during laser manufacturing.
-
Product
Fire & Flammability Test
-
Fire & Flammability testing: ASTM E119 [UL 263]; ASTM E152 [UL 10C]; ASTM E814 [UL 1479]; API 607, 6A; ASTM E108 [UL 790]; UL 1709; UL 1715; UL 2043; NFPA 286; UBC 26-2; UBC 26-3; ASTM E84 [NFPA 255, UL 723]; ASTM E162; ASTM E662 [NFPA 258]; ASTM D635; ASTM D1929; ASTM D2863; ASTM E1354; ASTM E1317; Room Burn Facility; CAL 133, 117, 129; UL 94 V/HB; IMO A.652 (16); IMO A.653 (16); ULVW I; ASTM D2859; AITM 2.0007; NFPA 701; FMVSS 302; FAA 25.853; IEEE 383
-
Product
Horizontal Flammability Tester
UI-TX40
-
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
Product
Open Flanges Test Rig
-
Flexible cell dimensions: cells of Ø 8 to Ø 80 mm (or square till 70x70 mm) can be successively installed Quick start of experiment: less than 20 minutes to remount a new cell with different dimension, thanks to the simple design without sealing Other SOFC components: the open flanges test rig is also useful for conductivity measurements (electrolyte, electrode material, interconnect etc.) and sealing tests End of broken cells and secure testing: the cell is squeezed by a soft alumina felt that prevents any damages, the excess fuel burns continuously in the alumina felt at the cell edges
-
Product
Environment And Burn-in Temperature Chambers
9000 Series
-
Delta 9000 Series Temperature Chambers offer a wide choice of temperature ranges and capacities in addition to smart electronics. Field proven by satisfied customers for over four decades, Delta chambers are quality instruments that provide service longevity and integrity unique in their field. Over the years, Cohu has added advanced features to the proven basic chamber design and has refined system components and programming capability to deliver outstanding quality and value.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Smoke Density Tester
TF350
-
TESTEX Testing Equipment Systems Ltd.
Smoke Density Tester , is widely used for density determination of smoke from the burning or decomposition of plastics and building material, designed according to ASTM D2843 and GB/T 8627. Equipped with high accuracy PLC and colorful touch panel.
-
Product
High Voltage Switching Test System
-
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
Product
Walk in Explosion-proof Chamber (Auxiliary Equipment)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Explosion-proof Chamber is mainly used to test the safety performance of lithium ion battery, battery pack. Prevent test operators and other test equipment from being burned and exploding. At the same time, the explosion-proof test chamber with the smoke exhaust system can discharge the smoke generated in the test to the outside.
-
Product
Burn Down Transformer
ATG 2
-
Cable fault location with the BAUR ATG 2. The ATG 2 burn down transformer is used for impedance reduction of cable faults in low- and medium-voltage networks. The short-circuit proof 2300 VA stray field transformer delivers a maximum voltage of 10 kV and is housed in a fully enclosed 19" housing.* Portable device for changing the fault resistance* Useful for cables that are difficult to access* Proven methods for complicated faults* Independent current and voltage control on each burning level
-
Product
Battery Projectile / Burning Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery projectile / burning tester is suitable for testing the flame resistance and flammability of various consumer batteries, such as mobile phones and notebook computers.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
DC Electronic Loads
-
Electronic Test & Power Systems
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.
-
Product
Burn-in Room and Aging Test Chamber
-
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of layer height in accordance with the requirements, convenient access ●Computer monitoring system is optional. ●Noise level:≤75dB Application Suitable for all kinds of electronic products, especially for products with heating characteristics Product and loading area should be separated Large-scale production
