Aero Nav Laboratories, Inc.
Aero Nav Laboratories is a full service environmental simulation lab that has served the military and industrial communities.
- 631-392-4888
- 631-392-4883
- AeroNavLabs@aeronavlabs.com
- 18 Connor Ln
Deer Park, NY 11729
United States of America
-
Product
Lightning Test
-
Lightning testing is used to determine the ability of externally mounted electrical and electronic equipment to withstand the direct effects of a lightning strike.
-
Product
Shock Test
-
Shock testing determines the ability of equipment to withstand the infrequent non-repetitive shocks encountered in handling, transportation, and service and to continue to function, where required. Also, shock tests verify that equipment will not detach from its mounting during these tests.
-
Product
Emergency Conditions Testing
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Terminal Mechanical Strength Test
-
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
Product
Vibration Test
-
Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. Vibration, for example, causes loosening of parts or relative motion between parts in the specimen, producing objectionable operating characteristics, noise, wear, and physical distortion, and often results in fatigue and failure of mechanical parts.
-
Product
Physical Testing Test
-
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
-
Product
Highly Accelerated Stress Screening (HASS) Test
-
HASS consists of high and low temperature and 3 axis vibration testing performed either individually or in combination.Highly accelerated stress screening is a technique for identifying process flaws in equipment during production. HASS subjects equipment to overstress conditions but at a level which does not affect design life.For assistance in designing a HASS test program contact the laboratory.
-
Product
Accelerated Weathering Test
-
Accelerated weathering consists of relatively long term exposure of items to specified environments.This test is designed to observe for material degradation.
-
Product
Electrostatic Discharge Test
-
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
Product
Fluid Contamination Test
-
Fluid contamination testing determines the abilities of materials to withstand the contaminating fluids, to which they are exposed in service.
-
Product
Noise Test
-
Noise testing is conducted to determine if materials can withstand external noises generated by various sources. It also includes air-borne and structure-borne noise measurements.
-
Product
Ozone Test
-
Ozone is an extremely reactive form of oxygen occurring around electrical discharges. It is also present in the atmosphere, but in small quantities. Ozone testing is performed to determine the effect on materials such as rubber, plastics, etc, which are susceptible to ozone-induced degradation.
-
Product
Temperature Test
-
The temperature tests are performed to determine if objects can operate normally under various temperature conditions, such as high and low temperature, temperature cycling, and temperature shock.
-
Product
Customized Services
-
We work in close collaboration with our customers to develop tailor-made test methods to meet their specific application requirements. Our 140 years of combined varied experience has allowed us to design solutions suited to address the needs of our customers in the most complex environments from space to deep sea.
-
Product
Corrosion Test
-
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
