Aero Nav Laboratories, Inc.
Aero Nav Laboratories is a full service environmental simulation lab that has served the military and industrial communities.
- 631-392-4888
- 631-392-4883
- AeroNavLabs@aeronavlabs.com
- 18 Connor Ln
Deer Park, NY 11729
United States of America
-
Product
Magnetic Effects Test
-
This test determines if an object can operate normally in strong externally generated magnetic environments. The magnetic effect test helps to assist in determining the proper location of the equipment in the installation.
-
Product
Radiographic Inspection Test
-
The radiographic inspection is a non-destructive x-ray method for detecting internal physical defects in small component parts which are not otherwise visible. Radiographic techniques are intended to reveal such flaws as improper positioning of elements, voids in encapsulating or potting compounds, inhomogeneities in materials, presence of foreign materials, broken elements, etc.
-
Product
Corrosion Test
-
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
Product
Sand & Dust Test
-
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Physical Testing Test
-
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
-
Product
Electrostatic Discharge Test
-
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
-
Product
Vibration Test
-
Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. Vibration, for example, causes loosening of parts or relative motion between parts in the specimen, producing objectionable operating characteristics, noise, wear, and physical distortion, and often results in fatigue and failure of mechanical parts.
-
Product
Pneumatic and Hydraulic Characteristics Test
-
Pneumatic and hydraulic testing is performed to demonstrate operating pressure, pressure drop, volume and flow parameters, as well as performance characteristics, of fluid system components and assemblies.
-
Product
Acceleration Testing
-
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
Product
Soldering Test
-
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
Product
Pressure Test
-
The pressure tests demonstrate if a test item can operate to its standard while undergoing extreme rapid pressure changes. Two of the pressure tests are: altitude (low pressure), and explosive decompression.
-
Product
Icing/Freezing Rain Test
-
This test evaluates the effects of icing/freezing rain on the operational capability of equipment. This method also provides tests for evaluating the effectiveness of de-icing equipment and techniques, using prescribed means that are used in the field.
-
Product
Electrical Contacts Test
-
The electrical contact testing is performed to determine the reliability of equipment under various contacting conditions. A few types of electrical contact tests are: contact-chatter monitoring, contact resistance, intermediate, and low level contact switching.
