Burn-In
The application of current, typically at high temperatures, over periods of time to detect infant mortality.
See Also: Burn-In Boards, High Power Burn-in, Burn-In Sockets, PCB Inspection
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
Burn-In Boards
-
Manufacture of burn-in boards since 1976. Established for more than 40 years in the market, Trio-Tech is recognized and is an approved global supplier to all major semiconductor companies. Trio-Tech has the capability to design and manufacture boards for all system types, with solutions available for many test conditions, Including HTOL, PTC, HAST and 85/85.
-
Product
Class 100 Clean Ovens
-
These models are used extensively in heat treatment/drying or burn-in of semiconductor wafers, liquid crystals, disks and other components and devices requiring clean air conditions. These units can also be prepared for installation in clean-room environments. Class 100 cleanliness is achieved by employing a HEPA filter and a back-to-front laminar circulation system. The high-performance models (with MS suffix) provides stable performance even during heat-up or cooling.
-
Product
Thermal Protective Performance Tester (TPP)
-
Sataton Instruments Technology CO., Ltd
Thermal protective performance tester (TPP) is to determine the heat transmission of protective clothing or textiles exposed to flame and radiant heat resources. The tester which can provide thermal protection index (TPI) calculated by software is the recommended tool for evaluation the potential of second degree burn of the materials to block convective and radiant heat penetration. Analysis software can display real-time temperature curve and automatically detect heat time curve to show Stoll curve for rating the thermal protective performance of tested textiles.
-
Product
Wireless Digital Multimeter 4000 count / NCV / SPT and with Anti Burn Protection
MS-W2034P2
-
This is a Palm Size external wireless connectivity Digital Multimeter integrated with 4000 Count, True RMS, auto and manual measurement.
-
Product
LGA Sockets
-
We’ve taken our QFN expertise and combined it with the versatility and performance of the H-Pin® to leverage an LGA socket platform that serves the demanding requirements of today’s market. Plastronics LGA sockets using the H-Pin provide a high-performance socket that is affordable for all burn-in operations. These LGA sockets meet the power, temperature and signal performance needs of the higher density, larger package outline, and sometimes mix-pitch LGA designs. The LGA platform serves package sizes from as small as 2.0mm X 2.0mm to the industry’s largest standard socket for 60.0mm X 60.0mm packages.
-
Product
IEC60695-11-2 Single Wire And Cable Vertical Burning Tester
CX-D12
-
Shenzhen Chuangxin Instruments Co., Ltd.
It’s strictly designed according to IEC60695-11-2, IEC60332-1, GB/T18380.11-2008, GB/T18380.12-2008 etc. Stainless steel screen with a sliding burner handle support for approaching or movingback the flame from the sample under test according to the CEI standards for test on cables.
-
Product
Horizontal Flammability Tester
TF311
-
TESTEX Testing Equipment Systems Ltd.
Horizontal Flammability Tester, to determine the comparative burn rates and burn resistance of textiles, particularly those for automotive interior use. Horizontal flammability tester is safe and easy to operate, Comprises draft free stainless steel cabinet with observation window, sample holder and door mounted burner.
-
Product
Corrosion Test
-
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
Product
Flash Point Testers
-
Flash point is the lowest liquid temperature at which a test flame causes sample vapors to ignite. Fire point is the temperature at which the test flame causes the sample to ignite and remain burning for ≥5 seconds.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Analyze RTL
-
ASICs and FPGA routinely have millions of gates with memories, transceivers, third party IP and processor cores. Problems can be time consuming and complex to debug in the lab and through simulations. Designers need verification tools that can identify problems quickly to reduce their verification and debug time before simulation, before synthesis, and definitely before burning chips in the lab.
-
Product
Goniophotometer
GMS2000
-
In this goniophotometer, the tested luminaire rotates in the prescribed burning position and around the vertical axle and a reflecting mirror rotates around the horizontal axle, meanwhile, a synchronous axle will rotate toward the opposite direction synchronously. The combined motion of the luminaire and mirror permit luminous measurement at the direction of any horizontal or vertical angle without tilting the luminaire, therefore, the luminous intensity will be not variation. The photometer head located at a fixed position of the limiting photomet- ric distance in front of the reflecting mirror to gather the light in each direction.
-
Product
6 ½ Digits Dual-Display Digital Multimeters
SDM3065X
-
The SIGLENT SDM3065X-SC includes a multiplexer that provides multi-point measurement capabilities. The scanner features 12 multi-purpose + 4 current channels and supports the following measurement functions: DCV, ACV, DCI, ACI, 2WR, 4WR, CAP, FREQ, DIODE, CONT and TEMP ( RTD and Thermocouple ). It provides a convenient and versatile solution for test applications that require multiple measurement points or signals and is an ideal tool for R&D burn-in and production testing.
-
Product
Burn-in Room and Aging Test Chamber
-
Aging test room according to your requirements. More types of Burn-In Test Room, Burn-In Chamber, Burn-In Test Oven wanted, please contact us freely.
-
Product
Package Level Test
-
Applicable for burn-in, reliability andlife testingACC and APC control modesIndividual channel driving and measurementDriving current 500mA per channel
-
Product
Stamped Spring Pin Sockets
-
Ironwood Electronics SBT sockets are small footprint sockets that are compatible with other product lines such as GHz elastomer sockets, Giga-Spring sockets, etc. The socket needs about 2.5mm extra space around the chip than the actual chip size utilizing only very small PCB real estate. A heat sink screw on the top provides the compression force as well as thermal relief and can be customized to dissipate more power. SBT socket uses SBT contact technology for high endurance and wide temperature applications. SBT Contact is a stamped contact with outside spring as well as inside leaf spring that provides a robust solution for Burn-in & Test applications. Solutions are available for 0.3mm to 1.27mm LGA, BGA, QFN, QFP, SOIC and other packages. Contact technology has 3 part system which includes top plunger, bottom plunger and a spring. The Beryllium Copper plungers are stamped and assembled to a stainless steel spring in an automated system to enable fast turnaround time, low cost and zero defects.
-
Product
Disk Drive Test System
Saturn
Test System
The Saturn HD is the industry leader in 3.5” Near-Line Hard Disk Drive (HDD) testing. It provides maximum throughput while minimizing factory floor space and power consumption. The system is designed to perform single insertion of SSW, BDSW and Burn-In as well as drive configuration. Using Saturn HD on the production floor will reduce drive build times, enable greater responsiveness to data center demands and lower test costs per HDD unit.
-
Product
Ultra High Speed Programmers
-
With superpro/7500 as the representative of the high-speed programmer, support chip comprehensive, burning faster, is adhering to the Superpro family's outstanding pedigree of the latest professional intelligent general programmer/burner/burner. Relying on Xeltek powerful device.
-
Product
Memory Burn-In Test
-
The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies.
-
Product
UL94 Combustion Chamber, IE60695vFlammability Tester
CX-S16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Horizontal Vertical Flame Tester is a comprehensive test instrument whick strickly designed according to Standard IEC60695, GB5169, UL94 and can meet the relative standard's requirements. It's mainly used to test the flammability of plastic and other nonmetalloid parts specimen to evaluate fire hazardous degree of accidental burning caused by the material.
-
Product
Semiconductor
-
With ultra-multi pin count and fine pitch, our general-purpose IC socket lineup corresponds to every need. For semiconductor burn-in sockets for thermal acceleration tests, and test sockets for semiconductor electrical testing, we continue to hold a high market share all over the world.
-
Product
Laser Diode Burn-in Reliability Test System
58604
Test System
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
HVR-LS Horizontal Vertical Flame Tester
HVR-LS/HVR-LSS
-
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
Product
Environmental Test Chamber
-
High and Low Temperature Test Chambers, ESS Environment Stress Screening, 2 Zone Thermal Shock Test Chamber, 3 Zone Thermal Shock Chambers, Walk-In Chambers, Burn-in Room and Aging Test Chambers, Altitude Chambers, Industrial Drying Oven, Salt Spray Test Chambers, Temperature Humidity Vibration Comprehensive Test Chamber, Test Machine Series, Custom Made Environmental Test Equipment, Double-Layer High and Low Temperature Chamber, Explosion Proof Temperature Chamber For Power Battery, etc.
-
Product
Flame & Other Plastics Testing
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
Product
DC Power Supplies
LPS Series
-
The LPS series power supplies are designed for various applications in semiconductor equipment along with OEM and industrial applications. Available for use in constant current or constant voltage applications they are available in power levels from 1,000 to 13,500 Watts. Common applications include heater, filament and magnet supplies along with test and burn-in applications. All models can be paralleled for increased power and custom configurations are available.
-
Product
Flash Point
-
At which temperatures will your sample burn, ignite, or cause fire? How are your flammable liquids composed, and what are their properties? Volatility is directly related to a substance‘s flash point temperature (flammability). Anton Paar’s flash point testing equipment safely and easily determines the values you require for the processing, storage, transportation, and classification of dangerous liquids.
-
Product
100Hz/120Hz/1kHz Handheld LCR Meter
U1731C
LCR Meter
Now you can measure at frequencies as high as 100 kHz, a capability that is typically found only in benchtop meters. With the auto identification, Ai which conveniently displays component type and detailed component analysis such as Z, ESR, DCR, you can get measurements done faster. Better yet, the battery lasts up to 16 hours, ideal for testing on the go. With the U1730 Series, you can perform quick, basic LCR measurements at your convenience, without burning a hole in your pocket.
-
Product
AC/DC Leakage Current Tester
228
-
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
