-
product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
product
Test Probes and Pins
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
product
Receiver, G12, 12 Module, 15" Platform, for Slide Mount
310104325-1
Receiver, G12, 12 Module, 15" Platform, for Slide Mount (slide kit required)**Please note - This part number ships with the platform not attached to the receiver. Platform must be assembled after delivery. The 15" G12 Receiver is a slide-mounted receiver. The 15" platform provides a surface to hold fixtures or other tools and supports up to 180 lbs. The 15" platform configuration is not compatible with the optional leg kit.This part number includes: G12 Receiver 15" Platform Mounting brackets (for attaching slide kit to platform) Left side microswitchSlide kit, keying kit, instrument bracket, right side microswitch, and any other accessories must be purchased separately. Designed for VPC 90-Series modules.
-
product
Kelvin IC Clip Lead
16089C
Measure odd-shaped components that you cannot measure using conventional fixtures
-
product
PXI Expandable 16x16 RF Matrix 50Ohm SMB
45-720A-511
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
PC Based Test Setup for LED Driver of LED
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
product
Safety Test Panel for Mixer
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
product
High Voltage Tester
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
product
Ethernet Test Fixtures & Software
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive Ethernet testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our Ethernet testing services also have access to.
-
product
SHC68-C68-D4, 68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - 1m
196275-01
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
product
Platform Solutions
The Slide Kits for the S6, G12, and G12x allow access to test instrumentation and wiring. Multiple accessories are available for this configuration such as the Cable Tray, the Keyboard Tray Kit, and Adjustable Leg Kit. Slides can support fixture weights up to 180 lbs [81.65 Kg] and up to 350 lbs [158.76 Kg] with legs
-
product
9025TR - 25 Module Solution with Platform
The 9025TR has over twice the I/O as the G12 and is outfitted with the same 20-inch platform to support enclosures while engaging and disengaging. The front-mount ITA is user-friendly, allowing the enclosure or fixture to be fastened from the mating side. The docking feature of the 9025TR provides an easy way of guiding a fixture into position prior to engagement. Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR uses all standard modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit.
-
product
Test Solutions Services
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
product
Deep And Sloped Pan Fixtures
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
product
Micro Probers
Flying Fixture
Yamaha Fine Technologies Co., Ltd.
Industry-standard testing machines for electronic circuit boards achieving high productivity and contact accuracy simultaneously. The pass rate and throughput greatly affect the productivity in the electrical testing process of circuit substrates. While improving both of these has proven difficult using the existing fixture method or flying method, Yamaha's Flying Fixture™ method has solved this.
-
product
Mechanical Design
In support of system, test and our tooling business, our mechanical engineering team is second to none in offering innovative, yet cost effective solutions for your needs.Whether it is a scalable test fixture solution or a complex, high accuracy torque tooling solution, our team of dedicated mechanical engineers can offer the right solution, with the right level of innovation to give your solution a competitive edge.
-
product
Small Footprint Flex 20 ATE
Flex 20
The Flex 20 is floor mounted but maintains a small footprint on the shop floor. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
product
Drop-In In-Circuit Test Fixtures
The Chameleon
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
product
Phase Array Ultrasonic Testing
PAUT
Sensor Networks, Inc. (SNI) is a Pennsylvania-based technology company specializing in the design and fabrication of industrial ultrasonic transducers and tooling for demanding in-situ test and inspection applications. Engineered for precision, ease of use, and maximum durability, our offerings include Phased Array ultrasonic transducers, fixtures, couplant-delivery systems, qualification/calibration standards, procedure development, personnel training and instrumentation.
-
product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and allows for sourcing the composite signal from the paired radio or from an external generator. The DME channeling outputs are monitored with discrete LED's as well as the ILS, V/LOC, Glideslope and NAV TEST valids. Discrete test jacks are provided for all the meters and the resolver of the NAV indicator and a dimming source is also provided. When testing the RMU 5000 computer access is through a dedicated connector.
-
product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
product
Functional Test Fixtures
Intrinsic Quality delivers turnkey standalone Functional Test fixtures and Windows based functional testers that are custom engineered with innovation and reliability to meet your testing needs. Our experience and expertise ensure a production ready functional test solution that is cost-effective, on time and on budget. Our broad range of test solutions includes simple continuity testers to complex microcontroller assembly testers. Our customers include military, aerospace, automotive, medical and consumer OEMs. We serve the needs of low volume high mix CEMs and off shore high volume manufacturers.
-
product
Custom Test Connectors and Sockets
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
product
Clamshell Type Mechanical Fixtures
Series 10
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
-
product
Fixture Kit
MF500
Electronic Test Fixture Kit Very low-cost kit facilitates use in situations where traditional fixtures are too expensive:o Research & Developmento Engineeringo Low-volume Production Uses include:o Debuggingo Programmingo Verification and Test
-
product
Through Connector Functional Test Fixtures
Circuit Check is a pioneer in the development and implementation of access mechanisms enabling testing of circuits through on-board connectors.
-
product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
Length Gauges For Measuring Stations And Multi-gauging Fixtures
METRO series
*High repeatability*Very high system accuracy of down to: ±0.2 µm*Ball-bearing-guided and zero-backlash plunger*Variant with reduced gauging force*Very long measuring ranges of up to 100 mm*Interfaces: 1 VPP, TTL, 11 µAPP*Protection rating of up to IP67
