Broadcast Monitors
-
product
VoIP Monitoring and Testing Tool
SIP Tester™
StarTrinity SIP tester™ is a VoIP load testing tool which enables you to test and monitor VoIP network, SIP software or hardware. It is able to simulate and passively monitor thousands of simultaneous incoming and outgoing SIP calls with RTP media, analyze call quality and build real time reports.
-
product
20Hz Injection Kit Monitoring System
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
product
Bulk Current Monitoring Probe
MP-50
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
product
Drive Recorders & Monitor
ES700
The ES700 family of products is focused on the in-vehicle tasks of data collection and monitoring. There are currently three products in this product family: The ES710 Drive Recorder, the ES715 Drive Recorder and the ES780 Heads Up Display.
-
product
Waveform Monitors
LV5350
The LV5350 waveform monitor offers a 7-inch HD screen display in a compact 3 x ½ RU package that can operate on AC or DC. Waveform, vector and picture with 4K 12G-SDI and audio options . Easy menu operation with touch screen, mouse, and front panel button controls.
-
product
Control and Monitoring of Machines
Millenium 3
Easy to program and to implement, it enables the control and monitoring of machines and automation installations with up to 50 I/O. It is positioned right at the heart of the Crouzet Automation range.
-
product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
product
Remote Corrosion Monitoring
Telemetry System
Metal Samples’ remote telemetry system obtains real-time corrosion monitoring data via the Internet from anywhere in the world. The system features communications via satellite to a secure Web Monitor data server. With this powerful web-based back end, you can bring the data to your desk no matter where the site is located.
-
product
Real-Time Quality Monitoring For 4K
RTM 4K
4K or multi-channel HD with 12G-SDI Interfaces Optional 10G IP for ST 2110 Networks
-
product
Environmental Noise Monitors
Our noise monitoring equipment is used across a wide range of applications and location. Each of these systems has been designed to meet the exact needs of the user by combining noise monitors with a software and support package.
-
product
Wrist CCTV Test Monitor
M-IPC-200B
Fuzhou Metricu Technology Co Ltd
4 inch IP camera tester with analog, HD-TVI, HD-CVI, AHD, wrist design
-
product
Condition Based Monitoring
Test Products International, Inc.
Vibration analysis at the touch of a button. Overall machine and bearing conditions: vibration values are displayed with color coded alarm levels for ISO values and Bearing Damage (BDU).
-
product
NGB (Next Generation Broadcasting ), Full C-band tunable (tuning range>35nm), 1550nm Externally Modulated Optical Transmitter
HT8800
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai HT8800 all C band tunable CATV external modulation optical transmitter, is an industry-leading and pioneer product. The tunable range of wavelength: 1528.77~1563.86nm, the adjustable wavelength: >35nm. With the traditional ITU standard wavelength ±0.8nm( ±100GHz ) can tunable, is a completely new concept and application ranges.
-
product
Application Monitoring Tool
Strong application monitoring tool enables IT teams, to get thorough insights into application health and response-time data. Go proactive with Motadata, which is one of the best application performance monitoring tools (APM) to identify potential threats that might bring operations down and fix the issue before it becomes a problem. Real-time metrics dashboard helps you stay on top of your application performance. Resolve application performance management issues before they impact your users or customers.
-
product
In-Ear Monitoring Systems
You will never believe how good you sound on stage, until you hear it.
-
product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
product
Clamp type AC Current Sensor／for Power Monitor
CT-80PB
MULTI MEASURING INSTRUMENTS Co., Ltd.
*BIG CT WINDOW*AC 1A～500A*Current measurements of main cable
-
product
Fiber Optical Monitoring Alarm System
FOMA
FOMA (Fiber Optical Monitoring Alarm System) is integrated RTU (Remote Test Unit) 、Center Monitoring Server and its management software to achieve integrated operation、remote management、unattended monitor、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record.
-
product
Partial Pressure Monitor for RGA
PPM100
Stanford Research Systems, Inc.
The PPM100 is a stand-alone controller/monitor for SRS residual gas analyzers. It measures partial pressures from SRS RGAs and total pressure from up to four capacitance manometers. Graphical output is available on a touchscreen LCD display.
-
product
Regulators, Monitoring, Sensors And Flow Control
All of the products in Parker's extensive pump and flow control product lines, from pumps and valves to motors and motion controllers, share a common heritage of advanced technology applied to meet the specific needs of our customers. In every instance and for every application, Parker components and systems are engineered to deliver precise and reliable control.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
Gas Monitor System
Henan Bosean Electronic CO.,Ltd.
Used to detect combustible, flammable and toxic gases, and oxygen depletion.
-
-
product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
product
Remote/Local Broadcast Quality Assurance
AlertCenter
AlertCenter allows you to monitor one or more remote capture locations, recording multiple channels at each location. You can monitor and manage them from afar, using a single, centralized user interface, greatly cutting manpower and operational costs involved in having a monitoring operation on every site.
-
product
Environment Monitoring System
ENVIROMUX-MINI-LXO
The ENVIROMUX-MINI-LXO features 2 temperature/humidity ports, 5 digital inputs, and 1 output relay for control of external devices. Linux inside.
-
product
PM Mass Monitor
Model T640
Teledyne Advanced Pollution Instrumentation
The Model T640 PM Mass Monitor is the next breakthrough in ambient particulate monitors. The T640 delivers 1-min or better time resolution with exceptional sensitivity and precision. The instrument is very low maintenance and requires no sample media for minimal cost of operation.
-
product
LCD Display Battery Monitor
TE6-0609
Hangzhou Tonny Electric & Tools Co., Ltd.
*Plug into a standard 12V/24V power outlet*Two USB outlets for charging 1x standard 1A and 1xhigh *output 2.4A*Voltage is displayed by digital read out to indicate battery*charge level*Flashing LED alarm and warning audible sounder indicates*low battery voltage*Replaceable 3A fuse*Suitable for 12V negative earth systems*Adjustable main plug angle*Ideal for the vehicle that double as a mobile office
-
product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 25 GHz, FC/PC
DXM25CF
The DXM25CF Ultrafast Detector is a DC - 25 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
product
Multi Monitor
MD
It is a 30mm monitor with 2 screens and 3 colors that displays 1-5V analog signals converted into numerical values.Since various unit displays are possible, it is ideal for monitoring pressure sensors and flow rate sensors.
