Product

Switch Probes

-

Smiths Interconnect

Smiths Interconnect

A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.

Product

Straight Wire Porbe Pins

Buckling Beam

-

Prospect Products Inc.

Buckling Beam - Prospect Products Inc.

Straight wire probe pins are a proven solution for various electronics production test environments.

Product

Structure-borne Probe

T20

-

SONOTEC GmbH

T20 - SONOTEC GmbH

The structure-borne ultrasonic probe T20 is used for condition monitoring of machines, systems and processes, given that they generate detectable structure-borne sound in the ultrasonic range. Changes in the sound signals indicate a change in the condition and/or process of the plant. The detection of these changes forms the basis for condition monitoring in predictive maintenance.

Product

Surface & Volume Low Resistivity Meter for Conductive Materials

Loresta GP

-

OAI

Loresta GP - OAI

The Loresta GX Meter is an intelligent, multi purpose low resistivity meter equipped with software that calculates resistivity correction factors. A variety of 4 pin probes are available for use with the Loresta GX. The instrument is typically used in Product Engineering, R&D, and Quality Control. Applications include measurement of conductive paint, conductive plastics, conductive rubber, conductive film, silicon wafers, antistatic materials, EMI shield materials, conductive fiber, conductive ceramics, etc.

Product

CAM/GATE Test Kits

-

Semco Machine Corp.

Semco Machine Corp.

The Camgate ™ series test fixtures provide ‘Z’ axis motion and, with the optional floating top plate, makes this series ideal for top side probing. The floating push plate is accurately registered with two tooling/guide pins. The top plate mounting frame is adjustable in .500″ (12.7mm) increments to accommodate top side probing in the lower position, or clearance for PCA’s with tall components in the middle or top position, without the need for riser blocks. Camgate fixtures are available with the most widely used interfaces in the test industry.

Product

Digital Multimeter

Basic

-

SparkFun Electronics

Basic - SparkFun Electronics

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity sound, current/voltage sense, and quality probes. You can use the multimeter to measure DC and AC voltage, DC current, resistance, continuity, and test diodes. With this version we've done away with the bright flashy colors that can get us into trouble and gone with a nice, neutral gray. This multimeter should provoke no strong feelings one way or the other, we know this because our guts say "maybe."

Product

Sensor Imitator Probe

-

AUTO DIAGNOSTECH LTD

AUTO DIAGNOSTECH LTD

The Sensor Imitator Probe is mainly used for the simulation of the signals generated by different types of sensors in the vehicle. It can be used in all automobiles (12V/24V), to distinguish faults that lie in the sensor itself or are related to the connectors or wires.

Product

Temperature and Humidity Regulator

H3021

-

COMET SYSTEM, s.r.o.

H3021 - COMET SYSTEM, s.r.o.

Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.

Product

Vibration

VEGASWING, VEGAVIB, VEGAWAVE

-

VEGA Grieshaber KG

VEGASWING, VEGAVIB, VEGAWAVE - VEGA Grieshaber KG

In point level measurement with vibrating level switches, a rod or a fork is set vibrating. When the vibrating probe comes into contact with the medium, the vibration changes and the vibrating level switch outputs a switching command. Vibrating level switches are used as overfill protection devices or low-level indicators in liquids as well as in granular and powdery bulk solids.

Product

Micro Probes

-

Equip-Test Kft.

Equip-Test Kft.

*Fine pitch applications *Pre - wired receptacles *30 Mil pitch

Product

Device Characterization

-

SemiProbe

SemiProbe

Probe systems for device characterization must be particularly flexible because many different measurements often must be performed; DC, IV/CV, Capacitance, HF, 1/f, temperature and more. The modular architecture of the PS4L product line is ideal for these broad requirements.

Product

Transmission Line Probes

-

Teledyne LeCroy

Teledyne LeCroy

Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.

Product

DIMM Interposer Probe

FS2361

-

FuturePlus Systems

FS2361 - FuturePlus Systems

The FS2361 is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154/64 Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 DIMMs.

Product

Digital Pocket Thermometer

212

-

Elcometer Limited

212 - Elcometer Limited

The probe conveniently folds back into the side of the instrument, preventing damage when not in use.Liquid or surface probe options availableUser switchable between °C and °FResolution can be set to 0.1°C (0.1°F) or 1°C (1°F)

Product

Probing Adaptors

-

Nexus Technology, Inc.

Nexus Technology, Inc.

Accessories primarily enable the connection between an industry standard logic analyzer footprint (D-Max, Mictor, P6860, etc) and an instrument probe. For example, a connection between a D-Max footprint and the digital channels of an MSO (Mixes Signal Oscilloscope). They can also enable the interconnect of a probe to a different industry standard footprint. Adding flying leads to a probe designed for a mictor footprint and a probe tester are also some of the accessories that are available.

Product

Structure-Borne Sound Probe

T10

-

SONOTEC GmbH

T10 - SONOTEC GmbH

The T10 structure-borne sound probe can be used to monitor the condition of machines, systems and processes, provided that they generate detectable structure-borne sound in the ultrasonic range.

Product

Probe System for Life

PS4L

-

SemiProbe

PS4L - SemiProbe

The Probe System for Life, or PS4L, is SemiProbe’s patented adaptive probe system architecture. Unlike traditional probe systems, all of the basics components of our systems, including the bases, stages, chucks, microscope mounts, and manipulators, are interchangeable, upgrade-able, and configurable. The PS4L Adaptive Architecture ensures and optimal test configuration for each individual customer application.

Product

Microscopic Four-Point Probes

M4PP

-

CAPRES A/S

M4PP - CAPRES A/S

CAPRES M4PP Microscopic Four-Point Probes have an electrode pitch three orders of magnitude smaller than conventional four-point probes, and are fabricated using silicon micro-fabrication technology.

Product

POWER PROBE III WITH CLAM SHELL - GREEN

PP3CSGRN

-

Matco Tools

PP3CSGRN - Matco Tools

*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground

Product

Manual Test Adapter With Rigid Needles

-

MicroContact AG

MicroContact AG

Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.