-
Product
Ultra Low Profile PCB Test Points
-
"Muti-Purpose" Style Test Points and Jumpers without Base
-
Product
Flash Point
-
At which temperatures will your sample burn, ignite, or cause fire? How are your flammable liquids composed, and what are their properties? Volatility is directly related to a substance‘s flash point temperature (flammability). Anton Paar’s flash point testing equipment safely and easily determines the values you require for the processing, storage, transportation, and classification of dangerous liquids.
-
Product
Breakout Box
T1000-37
-
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
Basic Contact Probes (75 Mil) F07515B120G100
1017265
-
As a Basic Contact Probe, F07515B120G100 (item number 1017265) establishes a spring-loaded electrical connection to the test point. With tip style 15 (Triangular 45° stepped), F07515B120G100 combines ICT/FCT use with a geometry intended for vias and solder pads where sharp edges can penetrate flux residues or oxide layers. F07515B120G100 combines a pitch of 1.9 mm / 75 mil with tip style 15 (Triangular 45° stepped) and a tip diameter of 1.2 mm. For F07515B120G100, spring force is 100 cN at a nominal travel of 4.3 mm. The electrical rating of F07515B120G100 combines 4 A continuous current with 20 mΩ typical contact resistance. The plunger in F07515B120G100 is made of beryllium copper and is gold-plated.
-
Product
Basic Contact Probe F70306B100G180L
1006526
-
As a Basic Contact Probe, F70306B100G180L (item number 1006526) establishes a spring-loaded electrical connection to the test point. With tip style 06 (Serrated stepped), F70306B100G180L combines ICT/FCT use with a geometry intended for wires, pins and wire-wrap posts; the geometry is also suited to slightly bent contacts. F70306B100G180L combines a pitch of 1.9 mm / 75 mil with tip style 06 (Serrated stepped) and a tip diameter of 1 mm. F70306B100G180L operates with 180 cN spring force and 4.3 mm nominal travel. The electrical rating of F70306B100G180L combines 4 A continuous current with 30 mΩ typical contact resistance. The plunger in F70306B100G180L is made of beryllium copper and is gold-plated.
-
Product
Cable and Harness Tester
CHT
-
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
Product
Color Coded SMT Test Points
-
Color Coded for easy identification, these surface mountable PCB test points are ideal for production testing and service troubleshooting. Phosphor Bronze, Silver Plated terminals allow for superior solderability and low electrical resistance. Wire loop design provides convenient access point for J-hooks, EZ hooks, grabbers, alligator clips, tips or probes.
-
Product
Basic Contact Probe F07505B120G280
1010962
-
F07505B120G280 (item number 1010962) is a Basic Contact Probe for repeatable temporary connections between the test system and a test point. With tip style 05 (Concave stepped), F07505B120G280 combines ICT/FCT use with a geometry intended for pins and wire-wrap posts with a guided, smooth contacting action. F07505B120G280 combines a pitch of 1.9 mm / 75 mil with tip style 05 (Concave stepped) and a tip diameter of 1.2 mm. For F07505B120G280, spring force is 280 cN at a nominal travel of 4.3 mm. The electrical rating of F07505B120G280 combines 4 A continuous current with 20 mΩ typical contact resistance. The plunger in F07505B120G280 is made of beryllium copper and is gold-plated.
-
Product
CAM/TRAC Test Kits
Series 40
-
The CT Series 40 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance.
-
Product
Phasing Voltmeter/Sensor (2 in 1)
-
STB Electrical Test Equipment, Inc
STB unit replaces 3 separate units manufactured by competitors - line phasing, capacitance phasing and line to ground Versatile, lightweight and easy to useEach portable meter has a single rangeMeter usage: Voltage detection and phasing at capacitance test points or voltage detection and phasing on bare energized conductors (overhead & underground)Probes can be separated to be used as a voltage sensor or capacitance sensorFive position selector.
-
Product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
Multifunction Switch/Measure Unit
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
Product
Time Domain Replication (Road Load Simulation)
-
The powerful graphical editor makes it easy to review and compile your field sample data for use in the test lab. The point editor, filters, velocity and displacement compensation ensure the test feasibility is evaluated at an early stage. The continuous closed-loop controller then replicates the test files with very high levels of precision. The control algorithms use a continuous coherence averaging technique to ensure a stable proactive control loop that will not only provide accurate replication but will also respond to changes in test item dynamics.
-
Product
Cable Phasing Meter
4183 CP
-
Standard Electric Works Co., Ltd
● Safely operates at low voltage ● Measures system voltage.● Measures capacitance of test point if system voltage is known.● Checks phase rotation of cables.● Phases out cables.● Rugged - comes with portable case.● Operates from potential test point of elbow connec-tors.● Battery operated.
-
Product
PNA-X Measurement Receiver for Antenna Test
N5264B
Receiver
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
Product
Breakout Box
T1000-9
-
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
Product
Copper Network TAPs
-
Network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers copper network TAPs in network speeds of 10/100M or 10M/100M/1000M (1G). Copper TAPs are purpose-built hardware devices used for out-of-band monitoring tools and make a 100% copy of your networks data allowing your monitoring tools to see every bit, byte and packet.®
-
Product
Debug Fixture
-
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
Product
PCB Test Points
-
Test Socket 2mm. Plug 2mm. Measuring Socket 2mm . 2 Pin Test Socket 2mm. Miniature Test Socket 2mm
-
Product
Optical Node
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Philips CGD914 amplifier module that employs both GaAs and Si dies.* 4 outputs, output level ≥100dBμV when optical input at -1dBm.* Plug-in fixed attenuator, fixed equalizer.* Optical power indication for -7 ~ 0dBm.* FP laser or DFB laser for return path.* RF test point for forward path and return path.* Optional SNMP responser unit supporting JIUZHOU HFC Net Managing software.* AC 60V or AC 220V power supply.* Aluminum die-casting housing.
-
Product
Propeller Meters
-
Measures accurately over a flow range of 10:1 or greater.± 2% of rate accuracy, guaranteed by certified wet calibration at three test points in.Sparling’s National Institute of Standards and Technology (NIST) traceable hydraulic flow lab.Sturdy cast or fabricated steel construction.Operating temperatures are over 100° F(unless higher temperature construction is specified).Suspended solids are over 0.5% of volume.Easily maintained with standard tools.Registration can be furnished in any standard Engineering Unit.
-
Product
PC Controlled Low Voltage Tester
Cablescan S32
-
The Cablescan S32, with a 32-board Expansion Cabinet, may be ordered with 1 to 32 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 4096 test points.
-
Product
Basic Contact Probe F58518S105L200
1001512
-
F58518S105L200 (item number 1001512) is a Basic Contact Probe for repeatable temporary connections between the test system and a test point. With tip style 18 (Conical 30°), F58518S105L200 combines ICT/FCT use with a geometry intended for solder pads and vias. F58518S105L200 combines a pitch of 2.54 mm / 100 mil with tip style 18 (Conical 30°) and a tip diameter of 1.05 mm. For F58518S105L200, spring force is 200 cN at a nominal travel of 4.3 mm. F58518S105L200 is rated for 5 A continuous current with a typical contact resistance of 20 mΩ. The plunger in F58518S105L200 is made of steel and uses Longtime Gold plating.
-
Product
Wire Harness Tester
NX Pro
-
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
Product
Plugbord
3682-2
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
Product
Digital Multimeter
8808A
-
The Fluke 8808A 5.5 digit multimeter dependably performs the most common measurements required by today’s applications. Whether you are performing functional tests or making critical measurements on test points, using the limit compare mode with pass/fail indicators eliminates production mistakes, especially those where results are “on the edge.
-
Product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
test
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
Product
Hand Insertion Tools
-
Zierick Manufacturing Corporation
Ideal for low volume, short run and prototype PCB assembly applications, Zierick’s hand tools offer a simple and reliable method for inserting press fit and splay mounted terminals. The hand tool can be easily installed on any type of press machine for increased flexibility and faster insertion. With the addition of a lower tool die, terminals can then be splayed and locked into place to improve reliability and prevent part removal and rotation. Zierick hand tools are available for PCB-mounted quick-disconnect terminals, quick-disconnect receptacles, post receptacles, test points and IDC terminals. Simple and reliable method for inserting press-fit and splay mounted terminals. Single tool can handle multiple terminal insertion applications. Tools can be installed on almost any type of manual or pneumatic press. Please click here for a PDF user manual for Zierick's hand tools.
-
Product
PC Controlled Low Voltage Tester
Cablescan S9
-
The Cablescan S9, with a 9-board Expansion Cabinet, may be ordered with 1 to 9 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 1152 test points.
-
Product
Slotted And Loop Types
-
As a practical alternative to wire-wrap posts and turret terminals, loop and slotted test points are an economical choice for reliable test terminations. Allowing non-slip, safe circuit testing, terminals easily attach to J hooks, EZ hooks, grabbers, alligator clips, tips or probes. Space saving, ultra-low and low profile designs are available for high density PCB applications. High profile designs are also offered for difficult to reach applications.
-
Product
Testers for Aerospace and Railway
-
Testers for the realization of a network with base unit and distributed test point units (TPUs).
