Calibration
maintains accuracy of test asset by correcting out of specification conditions.
See Also: Calibrators, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
Product
Spectrographs & Monochromators
-
Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. More than 100 gratings for the best spectral range, throughput and dispersion to meet your applicationDSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioningOptional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuationInstallation and set-up through USB 2.0 computer interfaces Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programsZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up
-
Product
Portable optical DO meter
ARO-PR
-
The Portable optical DO meter makes use of the fast-response optical DO sensor RINKO, maintaining its high-speed response performance (99% response < 7sec). The meter probe is equipped with a temperature sensor close to the sensing foil, and the measurements are made by simply inserting the probe into a DO sample bottle (the calibration is carried out using the National Metrology Institute of Japan (NMIJ) certified traceable gases standards). Differently from galvanic electrode sensors, the instrument does not require water sample stirring or fixing reagents, since there is no oxygen consumption. Thus, the required time to estimate dissolved oxygen is considerably reduced. The display unit shows the output instantaneously, and you can check the measured values in real time.
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
-
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Measurement Microphones
-
All microphones are omni-directional and 48V phantom powered. The XL2 Analyzer microphones include an electronic data sheet. The Automated Sensor Detection (ASD) of the XL2 automatically reads this data sheet, and recognizes the microphone model, sensitivity and calibration data. This ensures accurate measurement results.
-
Product
Automated Low Humidity Generation System
3920
-
The Model 3920 Low Humidity Generation System is a self-contained system capable of producing atmospheres of known humidity using the fundamental "two-pressure" principle. This system is capable of continuously supplying frost point, dew point, parts per million, relative humidity and other calculated values for instrument calibration and evaluation as well as for precision environmental testing.
-
Product
Analog Temperature Sensors
-
Analog Devices analog temperature sensors provide current or voltage output proportional to the absolute temperature with accuracies of up to ±1°C. Our diverse range of analog output temperatures sensors can be used in a broad range of applications with no need for external calibration, and with minimal signal conditioning/conversion circuitry. To better suit your varied design needs, our portfolio of temperature sensors are available in multiple package options.
-
Product
Calibration Lead Precision Resistor, Triple
40-975-009-SL3
-
The cable assembly is specifically designed to connect to the 9-Pin D-Type calibration port located on the front panel of Pickering Interfaces Module Part Numbers 40-260, 40-261, 40-262, 40-263 and 40-265.
-
Product
Thermistor Power Meter
N432A
-
Keysight N432A is the replacement for Keysight's legacy 432A analog thermistor power meter. The single-channel, average RF power meter operates with the Keysight 8478B and 478A thermistor mounts. The N432A-and-thermistor-mount pair is ideal for applications that require high measurement accuracy, particularly in metrology and calibration laboratory environments. The enhanced thermistor power meter comes with a digital color LCD display, and user-friendly front panel interface. Its built-in calibration factor table provides a more convenient and accurate method of storing calibration factors as compared to the old knob-turning approach of the 432A. The N432A is LXI compliant, and programmable via GPIB, USB and LAN.
-
Product
Camera Color Correction for Photo & Video
SpyderCHECKR™ Family
-
Automatically color correct your images by capturing SpyderCHECKR reference patches in your photo shoot, eliminating trial and error in post production. You can also color calibrate your camera and perform precision in-camera white balance.
-
Product
Thermocouple Simulator Module for SLSC
-
Bloomy’s 8-Channel Thermocouple Simulator Module provides eight channels of galvanically-isolated thermocouple simulation and simulates types E, J, K, M, N, and T thermocouples. High-precision digital-to-analog converters which are isolated from each other and from system power provide sub-microvolt resolution and accuracy. Built-in switching provides open-circuit faults as well as switching to system calibration resources.
-
Product
Gas Detectors
-
CO2, Humidity And Temperature Sensors, Dual Wavelength NDIR CO2 Sensor (Non-Dispersive Infrared) For Superior Stability, User Operated CO2 Calibration, Data Hold & Max/Min/STEL/TWA Function
-
Product
WEIGHING SYSTEM TESTING
1006
-
The Tester 1006 has a simultaneous control function of up to 4 load cells in any weighing system, upload and download function for programming the DAT and MC 302 series instruments, but it can also be used as a Calibrator and Peak detector. It is very useful for the correct mechanical installation and for fault diagnosis. The Tester 1006 is supplied as standard with cable for connection to our junction boxes / sum mod. CEM 4 / C and CGS 4 / C. Simultaneous display of the signal of each individual load cell allows to control the entire weighing system, weight distribution, overloads, faulty cells and faulty connections. OUT OF PRODUCTION. Pavone systems provides a new version of Tester 1006: Tester 1008.
-
Product
Hipot Line Testers
-
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
Product
Machine Calibration and Optimisation
-
Renishaw's laser interferometer and ballbar measurement systems assess, monitor and improve the static and dynamic performance of machine tools, co-ordinate measuring machines (CMMs) and other position-critical motion systems.
-
Product
Spectral Irradiance / Illuminance Calibration Standards
-
Standard lamps calibrated in illuminance and spectral irradiance. Traceable calibrations in the wavelength range from 200 nm to 2500 nm.
-
Product
Hydrophone
TC4047
-
The TC4047 miniature hydrophone offers a useable frequency range from 1kHz to 170kHz. The hydrophone incorporates a high quality 20dB low-noise pre-amplifi er which provides optimal conditions for signal transmission. The high sensitivity provides excellent signal to noise ratio and immunity against induced cable noise. The hydrophone is omnidirectional up-to 100kHz and has uniform receiving characteristic from 1kHz to 100kHz. An insert calibration circuit enables remote testing of the hydrophone condition. The hydrophone comes with a SEACON connector. The sensor element is permanently encapsulated in Special formulated NBR to ensure long term reliability. The rubber has been specially compounded to ensure acoustic impedance close to that of water. The strainrelief and outer jacket of the cable is made of high density polyurethane. TC4047 can be used in sea or fresh water.
-
Product
Three Axis Accelerometers
TAA
-
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
Product
LCR Meter
-
*Rs, Rp, Cs, Cp, Ls, Lp, phase angle, Dissipation factor, Quality factor *Auto select series or parallel test mode *Auto select 100Hz/1kHz/10kHz test frequency, 0.5V rms approx. *Calibration
-
Product
Optical Pickup
1037-DTS
-
TESCO introduces a new optical pickup (Catalog No. 1037-DTS) for one way meter communication through the calibration LED found on most solid state meters. The pickup senses infrared pulses from ANSI compliant meters for complete, automatic testing.
-
Product
Torpedo Digital Level
DL136
-
Advance Plus Trading Co., Ltd.
Model Number: DL136 Key Specifications/Special Features: Torpedo Digital Level with level bubbles,LED technology for the brightest display, IP65 standards 1. 25.4cm 10 inch level with 2 bubbles, 254*28*58.8mm（L*W*H）;2. Resolution: 0.01° at 0° and 90°, 0.05° at the rest°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.1° at 0° and 90°: ±0.2° at the rest;5. Measures angle in degrees, IN/FT, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13. With magnets in the bottom;14. With scales at the front bottom alumimum side;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP65 waterproof & dusyproof industrial standard.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
Bluetooth® Enabled Dissolved Oxygen (DO) & Temperature Pen
UltrapenX2™ PTBT5
-
*Industry Leading Accuracy*Display DO in Concentration, % Saturation, or Both*Adjustable for Altitude and Salinity*3 Calibration Methods: Air, Water and 0 ppm DO*Dynamic Membrane Temperature Correction*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Live or Hold Mode – User Selectable*Proprietary Sensor Design*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated ElectronicsWaterproofPowered by One N Type Battery (Included)
-
Product
Multi-Axis Calibrator
XM-60
-
XM-60 is a laser measurement system capable of measuring errors in six degrees of freedom along a linear axis, simultaneously from a single set-up. It provides a powerful diagnostic tool measuring all geometric errors in the axis from a single capture. For users of volumetric compensation XM-60 provides quick and accurate method of data population. All measurements are made optically allowing use in any orientation.
-
Product
Pulsed and CW lasers, 375 – 1700 nm, 1 kHz measurement rate
871 Series
-
The 871 Laser Wavelength Meter from Bristol Instruments is the best way to measure the absolute wavelength of both pulsed and CW lasers and OPOs. By combining proven Fizeau etalon technology with automatic calibration, the reliable accuracy needed for the most meaningful experimental results is ensured. What’s more, a sustained measurement rate of 1 kHz enables the wavelength characterization of every single pulse for most lasers. And, the resulting time resolution of 1 ms provides the most detailed analysis of tunable lasers.
-
Product
Ion/pH/mV Meter with Single Junction pH Electrode
Ion 6+
-
Direct Ion Concentration for use with most mono- or di-valent Ion Selective Electrodes (ISE) :: mV measurement mode allows you to check performance and calibration of your ISE
-
Product
Detectors
-
A detector head comprises one or more photodiodes each with an appropriate optical bandpass filter, diffuser, lens assembly, integrating sphere or other optical elements. Detector heads are calibrated in the Gigahertz Optik GmbH's calibration laboratory.
-
Product
Vibration Calibrator
SV 111
-
SV 111 vibration calibrator is the State of the Art instrument designed for human vibration measurements according to ISO 8041. The design of the calibrator is based on the triaxial reference accelerometer and microprocessor controlled shaker. These both features assure excellent stability of the calibration levels and their frequency independently from mass of the testing object, like also indicate improper test object fixing by monitoring of shaker vibration in all three axis simultaneously.
-
Product
Custom Barcodes
-
Verifier and scanner manufacturers often require custom barcodes for product evaluation, calibration, and quality control. Whether it’s a single code or a composite sheet of multiple codes, symbologies, minimum x dimension, etc., APPLIED IMAGE produces these custom, photo-composed standards to meet the needs of our global base of customers using our proprietary ACCUedge® technology.
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
pH 700 Benchtop pH Meter
-
The easy-to-use, microprocessor-based pH 700 benchtop meter measures pH, mV, relative mV, and temperature. The large, dual-display LCD provides excellent visibility—even from a distance. Automatic temperature compensation (ATC) maintains reading accuracy even with fluctuating temperatures. Five-point pH calibration, with automatic buffer recognition for both USA (pH 1.68, 4.01, 7.00, 10.01, 12.45) and NIST (pH 1.68, 4.01, 6.86, 9.18, 12.45) pH buffers, makes for easy calibration no matter which requirement you need to meet. Meter features HOLD, ATC, selectable °F or °C measurement, recall of electrode slopand offset, and electrode diagnostics. The convenient pull-out quick reference card keeps procedures handy at all times. Meter accepts any pH or ORP electrodes with a BNC connector.
