Memory Test Systems
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Test System
MFTS500
Computer Gesteuerte Systeme GmbH
The MFTS500-System is specially designed for the testing of electronic control units (ECUs). It can be configured to be used as a development or as a production tester. Every effort has been made during development and design to ensure that the system is flexible and cost effective.
-
product
H(3)TRB & HTGB Test Systems
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
product
Memory Tester
RAMCHECK LX DDR3
Quickly test DDR3 DIMM and SO-DIMM memory. In just seconds, RAMCHECK LX will perform a thorough test of the module and provide complete identification. Also tests expensive LRDIMM modules.
-
product
Test System
RF-1 ATS
The RF-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
product
NI's Electrical Functional Test Solution
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
product
Memory Recorder
MR8847A
High-speed 20MS/s, 16-channel, Fully Isolated Memory Recorder for On-site Jobs and R&D
-
product
Lens Module Test Platform
The Lens Module Test Platform is a flexible solution to deliver the quality that is expected from your brand for all types of lenses and cameras. The system can be configured to measure objective, eyepiece or camera lenses. As the platform can efficiently measure lenses as small as 2 mm3, it is perfect for the critically precise applications of life sciences, consumer electronics, automotive and other industries. With 25+ years of quality experience, the Lens Module Test Platform ensures that all products shipped to market work as intended.
-
product
Semiconductor Memory Tester
T5851
Advantest Corporation has introduced the T5851 system, designed to provide a cost-effective test solution for high-performance universal flash storage (UFS) devices and PCIe BGA solid-state drives (SSDs) memory ICs in high demand by makers of low-power, mobile applications such as smart phones, tablets and ultra-portable laptops. The flexible T5851 tester is available in both production and engineering models. This allows the system to be used for reliability and qualification testing as well as test-program development or, when equipped with an automated component handler such as Advantest''''s M6242, high-volume production. As a fully integrated, system-level test solution, the T5851 provides multi-protocol support in one tool while its tester-per-DUT architecture and proprietary hardware accelerator allow it to achieve industry-leading test times.
-
product
SoC Test Systems
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
product
Test System
DA-2 ATS
The DA-2 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
product
Mezzanine System
5174
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
product
Optics Test Systems
Lens Test
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
product
IT Battery Test System
Shenzhen Sinexcel RE Equipment CO., Ltd
IT battery test system support for multiple charging mode (such as CC, CV, CP, pulse, etc.) and discharge mode, to ensure that the battery performance and safety in the practical application. IT battery test system is designed to be modular, easy to maintain, and with anti-reverse connection, data loss and other protection functions
-
product
Multi-Functional Optical Profiling system
7505-01
Chroma 7505-01 is the newest multi-function optical inspection system that equips with the capability of measuring 1D, 2D and 3D at the same time. Penetrating reflection measurement is used for 1D film thickness measurement to measure the non-destructive film thickness on transparent and translucent material.
-
product
Modular Test System
DMT
The DMT Tester is a modular test system that allows rapid measurement of electrical and non-electrical parameters of functional units. The system also allows basic ICT measurement with optional accessories. It is conceived as modular, with the possibility of integrating a wide range of own and external instruments. The DMT tester is controlled by its own SCADUS software.
-
product
Brake Test Systems
GIANT 9000 Series
The major test target is to detect noise and vibrations generated by the vehicles brake. Our intention was to build a dynamometer that can operate either with brakes mounted to the complete vehicle, or with just the axle module mounted to a universal adaptor system or wheel suspensions.
-
product
Stress Testing System
Load Dynamix
LoadDynamix (former Swifttest) is famous for its IP based converged storage system stress testing, including iSCSI, SMB/CIFS, NFS, FC and HTTP/HTTPS based storage systems. Its GUI interface is very easy to use and allow customer engineer to fully configure all the parameters at the protcol layer. Nearlly all the major IP storage system manufacturers have LoadDynamix products in their test lab.
-
product
Optics Test Systems
IR Autocollimator
Optik Elektronik Gerätetechnik GmbH
The infrared autocollimator was specially designed for the 1550 nm wavelength range. In conjunction with the CROSDETECT evaluation software, it achieves a measuring accuracy of 1 arcsec with a resolution of 0.1 arcsec. The camera used is suitable for the wavelength range from 900 nm to 1700 nm.
-
product
Brake Test Systems
Giant 8000 Series
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
product
Automotive Test System
LABCAR
The LABCAR product family comprises software, hardware, and models suitable for integration into tailor-made testing systems that fit perfectly into existing processes. Deployable from the earliest to the latest phases of development, the LABCAR family provides for efficient verification and validation of embedded systems and software.
-
product
MEMS Testing System
BK3010V2
The BaKo BK3010V2 is our updated MEMS Tester, based on our C-Mic tester, the best selling BK3010. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is very easy and can be done in a few minutes. In addition, the new BK3010V2 can be connected to a computer so you can keep and view compiled data and track trends in variations in your C-Mics.
-
product
RFID Test System
RFID test system of Peritec is making FPGA board (IF-RIO) the processing of the IF band. This reading of the code, called (Electronic Product Code) EPC is required for RFID tag ISO18000-6 TYPEC of (EPC C1 G2). However, it did not provide treatment too late in the traditional instruments.
-
product
Memory Burn-In Tester
H5620/H5620ES
As Server and Mobile applications have mainly led the Memory and market has also entered a super cycle that has completely withdrawn from the previous silicon cycle.Memory capacitance will continue to rise as the application of data processing and mobile communication occurs—however, revenue will not grow as ASP goes down. Suppliers need to reduce test costs and increase profits.H5620 contributes to reduction of test cost by integrating the test process of DRAM Burn-in and Core Test. This hybrid memory test solution solves the challenge of reducing test costs while increasing test efficiency in the expanding DRAM market.
-
product
microLED Testing System
OmniPix-ML1000
The OmniPix-ML1000 is the first all-encompassing microLED testing system, offering both full wafer and localized individual pixel inspection. Measure localized and total EQE. Use automated PL and EL to test and characterize your microLEDs. Analyze defective pixels with nano-PL and nano-EL.
-
product
Modular Test System
IMU-MGE
Modular test system with colour touch screen and intuitive software. An integrated help with graphics guide the user through fast and efficient setup and operation. The system is used for CE mark testing in the European Union. Each system can be individually configured and easily extended.
-
product
Functional Test Fixtures
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
product
Portable Test System
MT786
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
product
Relay Test System
Relay test products that combine a flexible hardware architecture with advanced test software. Relay tests can be constructed within minutes and displayed using a very simple interface, making the system ideal for low-cost production applications.





























