Filter Results By:
Products
Applications
Manufacturers
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-01
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
Trailer Light Testers
Pro-Check 725
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
product
Switch
TOE 9261
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-02
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
product
Earth Fault Detector
K-3838
Kongter Test & Measurement Co., Limited
Kongter’s K-3838 earth fault detector is the updated model which is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems where electrical cables have breakage and current lost to ground. It will save you from long time unnecessary troubleshooting and helps to increase the reliability of your electrical equipments. Our unique technique makes it safe and fast to handle earth fault in DC systems that are working online.
-
product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
-
product
Sensors
Honeywell Aerospace Technologies
Honeywell is a trusted leader in providing sensor products for commercial, defense and space applications. Honeywell’s accelerometers, precision navigation, precision pressure transducers and barometers, high performance microwave applications, magnetic sensing, thermal qualified and radio frequency monitoring/sensors are designed for the harshest environments in the air, ground or deep underwater.
-
product
Dual Quad Core Multiprocessor
DSP282A
Designed for size, weight and power (SWaP) sensitive applications, Abaco's high performance embedded computing (HPEC) platforms deliver expanded mission capabilities across a wide range of manned- and un-manned airborne, ground and naval platforms.
-
product
Signal Isolators & Converters
Devar current loop signal isolators reduce problems found in field measurements when signal transmitters or converters encounter both input and output signals that may be grounded. Current loop isolators eliminate these ground loops and are available as input loop powered or output loop powered instrumentation.
-
product
Modulator
SFT2406G
Hangzhou Softel Optic Co., Ltd.
SFT2406G DVB-T/T2 modulator is our new product developed complying with the DVB-T/T2 standard. With its advanced modulating technology, this modulator can effectively make use of the ground spectrum resources and make it possible to provide reliable signals for fixed, mobile and portable devices. Compared with DVB-T, the channel capacity is increased by 30% under the similar carrier to noise ratio (CNR) threshold. Moreover, this device can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and provide good signals for scientific laboratory and DVB-T/T2 STB.
-
product
- RS-422 and RS-485 Lightning/Surge Protector
Model 22NX
FEATURES: Triple Stage Protection; Fast Response Time For RS-422 / RS-485; Prevents Damage to Modems, Converters, and Terminals; Accommodates Data Rates to 10 MBPS; Supports 4 Circuits. The Model 22NX Lightning Sponge is designed to accommodate high-voltage transients, slow them down and redirect them to a low impedance path to earth ground.
-
product
Ground Threat Emitter Sensor System
GTESS
The Ground Threat Emitter Sensor System (GTESS) is a modular test and training system capable of stimulating multi-spectral aircraft electro-optic sensor suites at long range. The GTESS system integrates Textron Systems’ ultraviolet (Mallina™), infrared (Phoenix) and/or laser (Phantom™) ranged stimulators with an automated tracking system to facilitate fast-moving test, training and evaluation exercises. A fully integrated camera system for effective after action review. GTESS can also work in conjunction with Textron’s radio frequency (RF) range stimulator systems (PRTS™ & HPRTS) for complete multi-spectral testing.
-
product
Lightning Warning Sensors
Lightning warning sensors measure the local, atmospheric electric field at the earths’ surface and the fluctuations in field strength. By monitoring the field strength, the potential for cloud-to-ground (CG) lightning discharges can be detected, and advance warning can be made when conditions are becoming favorable for lightning.
-
product
Multifunction Substation Test Set
STS 4000
STS 4000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers, designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
product
Circbord
8003
VECTOR Electronics and Technology, Inc.
Pad per hole & peripheral ground plane.0.085” Square pads etched around each hole on wiring side.Accommodates any type DIP IC device or discrete component.Single sided board with pads and peripheral GND plane on one side only.Single-sided with no etch and plating on reverse side.
-
product
Common Point Ground Connector
Q007-T
The Prostat Q007B Qube™ replaces ordinary electrical grounding devices with a convenient, cost effective means to connect several ESD controls to a single grounded electrical outlet. Use the Q007B Qube™ to ground workstations, mats, wrist strap & testers, instruments, and other ESD control products to a pre-tested facility electrical ground. It consists of a robust multi receptacle frame encased in fire retardant ABS with a solid brass grounding pin.
-
product
Guardian Ground Bond Tester
19572
Chroma Systems Solutions, Inc.
Wide resistance measurement range : 0.1 ~ 510 mΩHigh performance AC current output : 45 ACompact size ground bond testerProvide reliable and stable test resultsBuilt-in resistance compensation functionStandard RS-232 interfaceOptional GPIB InterfaceCompatible with the model 19070 series Hipot Tester2-Year factory warranty
-
product
Variable Power Supply
VS-10a
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
product
S-100 Bus, Vectorbord Plugbord
8801-6
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side)on 0.125"(3.175mm) centers. Pad per hole (square) both sides. I/O mounting area for ribbon cable header.Row and column legends provided. S-100 Form Factor.Pin 1 and 51 committed to power. Pin 50 and 100 committed to ground.
-
product
Gold Probes
4900 Series
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
product
Resistivity Meters
Periodic compliance checks of ESD work surfaces are super important. Monitors only verify the ground plane, or path to ground. The surface itself can wear down, become dirty, or if you use low quality mat—just not hold up. A handheld Surface Meter is great for running monthly, or prescriptive compliance verification of your ESD surfaces.
-
product
Ground Fault Locator
K-800
Kongter Test & Measurement Co., Limited
Kongter’s K-800 Ground Fault Locator is the new model which is developed to fast detect, trace and pinpoint virtual ground faults in LIVE DC systems where electrical cables have breakage with current lost to ground.
-
product
Airborne Receivers & Bit Synchronizers
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
product
Ammeters
*Measures AC current from 1 to 2000 Amps on system voltages up to 500kV line-to-ground*Stores the last 4 readings*Dual measurement modes, peak hold and real time*Takes spot-load checks with ease*Verifies phases are balanced*Versatile for overhead and underground applications*Compact, lightweight design
-
product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Modul
780878-01
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
product
Earth Ground Test Lead Kit
TL-796
*Earth Resistance Test Lead Kit*For use with IDEAL 61-796 3-Pole Ground Resistance Tester
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
product
Wrist Strap and Foot Wear Testers
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
product
Self-reclosing Overcurrent And Residual Current Protection
Wide range of solutions to guarantee personnel safety as well as maximum service continuity in the event of a ground current or breaker trip, with automatic reconnection of the installation. Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
