Wafer Level Reliability
-
Product
Probe Card
VC43™/VC43EAF™
-
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
Product
MPI Automated Probe Systems
-
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
Product
Semi-Automated Probe Stations
SPS 2600, SPS 2800, and SPS 12000 Series
-
The SPS 2600, SPS 2800, and SPS 12000 Series systems are MicroXact’s semi-automated probe stations designed to be flexible and easy to use when performing high productivity device characterization, wafer level reliability testing and failure analysis. These semi-automatic probe station systems are designed to support manual and semi-automatic probing of up to 200mm wafers.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
Product
Probe Card
VC20E Series
-
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
Product
Probe Card
T90™ Series
-
The 90 mm tile was designed for mounting on a standard 4.5″ probe card holder for multi-site wafer level reliability testing. The 1.6 mm (0.062″) thick rails allow the chassis to slip into planarity adjustable probe card holders for most analytical probe stations.
-
Product
Wafer Level Test
-
Double sided wafer inspection system is an automatic inspection system for afterdicing wafer chip. It can do double side inspection simultaneously. The appearance defects of wafer chip are clearly conspicuous by using advanced illumination technology. Illumination and camera acquisition mode can be adjusted for various wafer process, like vertical chip or flip chip.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Reliability And Durability Testing
-
Underwriters Laboratories Inc.
Our reliability and durability testing services provide an accurate assessment of how your product may perform under expected and unusual use. We can help you meet regulatory requirements, gain actionable knowledge about the anticipated life cycle of your products and identify design flaws that have adverse effects on a product’s reliability and durability.
-
Product
Wafer Probers
-
Devices to align probes to test the electrical properties of IC chips or TEGs (Test Element Groups) formed on wafers. The vast options available will meet various needs, from research to mass production.
-
Product
Lighting Reliability
-
LED/OLED package lifetime is highly dependent on thermal management, and LED lamp performance can be dependent on the luminaire in which it is installed. Lighting reliability test system for LED/OLED Products are widely used for normal /accelerated aging, lumen maintenance measuring, lifetime evaluation and temperature characteristic testing for LED/OLED products including LED package, array, module, OLED module and luminaires.
-
-
Product
Ultrasonic Wafer Scanner
AutoWafer
-
Installed in more wafer applications than all other automatic ultrasonic testing tools combined, AutoWafer provides a complete, production-ready wafer scanner for wafers from 100mm to 200mm, including multiple sizes in a single batch.
-
Product
Wafer Probe Heads
-
WLCSP test is the applying final test conditions at Wafer Level. WLCSP testing is driven in lowering the cost of test of devices through economical methods of manufacturing and testing.
-
Product
Wafer Mapping Sensor
M-DW1
-
Panasonic Industrial Devices Sales Company of America
To provide better safety and improved sensing accuracy, Panasonic studied the requirements for future Wafer Mapping Sensors to ultimately develop the LED Beam Reflective Type Wafer Mapping Sensor, M-DW1. This Sensor uses LEDs as a light source for safe operation and a 2-segment receiving element for higher accuracy in wafer detection.
-
Product
Wafer Manufacturing
-
Scientific Computing International
A procedure composed of many repeated sequential processes to produce complete electrical or photonic circuits on semiconductor wafers in semiconductor device fabrication process.
-
Product
Level Switches
-
Omega can meet your level measurement requirements by offering switches of various technologies including capacitance and conductivity, tuning fork, ultrasonic, optical, and rotating paddle switches.
-
Product
Levels And Protractors
-
Reads either actual level or a relative angle between two surfaces.
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
Product
Level Sensors
-
*High reliability due to the elimination of mechanical components*Different function principles: Guided wave radar, capacitive and hydrostatic*Devices for limit level detection or continuous level measurement*Clearly visible LED display*Suitable for all common industrial and process fluids
-
Product
Level Switches
-
Omega can meet your level measurement requirements by offering switches of various technologies including capacitance and conductivity, tuning fork, ultrasonic, optical, and rotating paddle switches.
-
Product
Laser Diode Burn-in Reliability Test System
58604
Test System
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
Combined Environmental Reliability Test System
VTC SERIES
-
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Product
Wafer Testing
Trio Vertical
-
SV TCL's TrioTM is a reliable solution for advanced wafer testing challenges, specifically full array and parallel probing. We offer a complete line of vertical probe card products, each designed for your unique application.
-
Product
Level Switch
Z-Tron IV
-
The Z-Tron IV level switch is one of our most popular on/off level switches offering an effective, low-cost material level detection in a wide variety of applications. It is widely used as an alternative to electromechanical level switches.
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
MPI PA Wafer Probers
-
MPI Photonics Automation is the industry-leading provider of turnkey wafer test and measurement solutions. We offer a complete line of high-performance wafer probers designed to address the diverse and complex needs of the Photonics, Optoelectronic, Semiconductor, and Laser industries.
-
Product
Wafer Bonder
AML
-
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
Product
Reliability Solutions
RT-300
-
RT-300 is a customizable ecosystem of connected insights, which empower plants and teams to proactively identify maintenance needs, make smarter decisions and keep machine performance and profitability at optimum levels.
-
Product
Reliable CAN Measurement Technology
CNT evo CAN MM Series
-
The CNT evo is a high-precision measurement module designed for measuring frequencies, pulse widths, incremental displacement measurements, rotation angles, position measurement, event counting and period measurements.
