LED Test
See Also: Flicker Analyzers
-
Product
Memory Test System
T5230
Test System
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
LED drivers
-
ST offers a large portfolio of energy-efficient DC/DC powered LED driver ICs for general lighting, display LED backlighting, automotive exterior and interior lighting, RGB and monochromatic LED drivers for signage and traffic signals.
-
Product
Testing
-
Apogee Labs offers a wide variety of modular chassis types used for test applications with various Data Link Test Modules.
-
Product
LED Spot Type UV Curing Systems
AICURE UJ30/35
-
Panasonic Industrial Devices Sales Company of America
The compact UJ30/35 UV Curing System can be equipped with up to four individually controlled LED heads. Different types of UV-LED heads are available with an irradiation wavelength of either 365nm, 385nm or 405nm. The Controller allows for external contact inputs or PLCs for automated applications.
-
Product
Load Testing vs. Stress Testing
-
A load test is a planned test to perform a specified number of requests to a system in order to test the functionality of the system under specific levels of simultaneous requests. A load test ensures that a web system is capable of handling an expected volume of traffic, and therefore is sometimes referred to as volume testing. The goal of a load test is to prove that a system can handle the expected volume with minimal to acceptable performance degradation. The threshold of acceptable performance degradation must be defined by the testers as some value considered acceptable to the end user so that users will not bounce from the site.
-
Product
Medalist i1000D
U9401B
In-Circuit Test System
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
-
Product
LED Lighting Drivers
-
Renesas' dimmable AC mains LED driver with PFC and primary side regulation provides all of the features required for high-performance dimmable LED ballast designs and supports AC or DC input, isolated or non-isolated flyback and boost topologies.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
Compliance Test, Development and Test Service
DinoStor
-
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
Product
Testing Services
-
We are professionals who deliver software testing services. We are able to boost your software testing, increase product quality and reduce costs.
-
Product
Game Testing
-
Here at UpDoerTech, we strive to improve the gaming industry by providing the most comprehensive, accurate, and efficient testing mechanism. We've built an A/B testing framework so that you don't have to guess or speculate what gamers think of all your features. Our team of QA experts will help you find bugs early in the development process so that your product ships with fewer issues.
-
Product
Test Enclosures
Enclosure
The HV test hood, developed by us in accordance with EN50191 standard (erection and operation of fixed and temporary electrical test installations), is designed for testing large quantities in ongoing production. The ergonomic design ensures fatigue-free operation even during repetitive work sequences. Equipped with all safety-relevant functions, such as safety switch and locking of the hood cover during the test sequence, the operator is optimally protected at all times.The interchangeable adapter plate within the test cell allows quick adaptation for different test conditions and test situations.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
Test Compliance
CTS Series 3.2
-
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.
-
Product
Lightning Test
-
Lightning testing is used to determine the ability of externally mounted electrical and electronic equipment to withstand the direct effects of a lightning strike.
-
Product
Test Facility
-
Emprise has extensive experience designing test facilities for the aerospace, automotive, industrial and power generation marketplaces. The cost of a test facility is usually directly proportional to the accuracy of the test simulation.
-
-
Product
Test Fixtures
-
At A.T.E Solutions we have a dealt with a wide range of test subjects in the past 30 years and have extensive experience in providing reliable test fixture solutions.
-
Product
Load Testing
OctoPerf
-
Use auto-correlations rules and frameworks as well as test validation to quickly create virtual users.
-
Product
Factory Testing
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Efficient factory testing is vital in order to achieve the tightest tolerances, maximum repeatability, high precisi- on and quality in the manufacturing processes, as well as long production machine lifecycles. What‘s more, it helps to reduce manufacturing costs due to minimized replacements, retesting processes, and recalibrations. Online CatalogApplication Notes
-
Product
Circuit Testing
-
Circuit testing is generally the first diagnostics performed on an electronic device that has stopped working. Circuit testing determines whether electrical current can travel through a circuit. Resistance, measured in ohms, is the measure of the resistance in a circuit.
-
Product
Electrosurgery Testing
-
High-performance electrosurgery testing solutions for ESU generators.
-
Product
Instrument Systems LED Measurement Accessories
-
Konica Minolta Sensing Americas, Inc
It’s critical to use the appropriate LED measurement equipment and accessories when evaluating an LED’s various photometric and radiometric quantities. Because all of the test adapters Instrument Systems designs are compliant with CIE 127:2007, users are assured of compatibility between measurements. Instrument Systems has a diverse array of LED Measurement Equipment.
-
Product
Transformer Testing
-
The ART-3D series of Automatic Ratio Testers are precision instruments, designed to measure the turn ratios, phase displacements, excitation currents of single phase and three phase power, distribution and instrument transformers in conformity to the IEEE C57.12.90 & IEC 60076. Now featuring an enhanced test lead design, the ART-3D is the perfect instrument for real-life field usage. ART-3D series also has Anti Induction circuit which makes it suitable for system voltages upto 765KV.
-
Product
Package Test
-
WinWay’s commitment to technology, quality and service ensures our interface solutions go above and beyond to exceed your expectations. Our products and services have a proven track record of delivering customer success in semiconductor testing. The Company offers comprehensive test interface solutions ranging from wafer-level test, package-level test to thermal management.
-
Product
LED Driver Automatic Test System
ATE-2
-
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
Product
Vision Testing
-
Visual evaluation is a critical step in achieving accurate color, and ensuring accurate color vision is a must. Farnsworth-Munsell Hue Test solutions allow you to evaluate the color vision of your team.
-
Product
Network Testing
-
Service Providers are under significant pressure as service revenues plateau, competition intensifies and traffic growth skyrockets. Service Providers have relied on Enghouse Networks automated network testing for decades because this mission-critical solution adds significant and tangible business value. The solution enables Service Providers to improve network reliability and performance, accelerate time to revenue for new services, minimize expensive truck rolls and improve customer satisfaction.
-
Product
Vibration Testing
-
DATASYST Engineering & Testing Services, Inc.
Small, medium and large electro-dynamic vibration systemsServo-hydraulic vibration systemsCombined environment system (Temp-RH/Vibration)
