Test Cards
See Also: Cards, Extender Cards, Probe Cards, POST Cards
-
Product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
Interface Card
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-429UNET/RT8-717 adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher).
-
Product
Component Test Systems
Test System
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
Product
ARINC PCI Express 4 Lane Interface Cards
PCIE4L-A429
Interface Card
Alta Data Technologies’ PCIE4L-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal. The 4 lane card (PCIE4L) is normal 1/2 height common for most desktop and larger server systems.
-
Product
Edge Card Adapter, Universal, for .093 PCB
111107148
Edge Card Adapter
VPC provides two types of Edge Card Adapter Kits for 10, 25 and 50 Module ITA Enclosures. Both kits are designed for various sized cards.The Universal Edge Card Adapter Kit’s card guides are hinged and can be folded for storage by releasing the holding latches on either side of the card.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Functional Test
cUTS
Functional Test
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
Product
NI HIL and Real-Time Test Software Suite
test
Suites combine LabVIEW Professional Development System with NI's most popular application softwareIncludes LabVIEW Professional, VeriStand, and the LabVIEW Real-Time and LabVIEW FPGA modulesEach new suite includes a one-year NI Training and Certification membershipSoftware is shipped on USB 3.0 media with NI device drivers included to speed up your installationConfigure real-time test applications quickly and easily; add custom functionality
-
Product
PSI5 Sensor Interface Card
SET-1640
Interface Card
PSI5 is an open standard based on existing sensor interfaces for peripheral airbag sensors and has already proven itself in millions of airbag systems.
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
NI Real-Time Test Cell Reference System
780590-35
test
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Scienlab Battery Test System — Cell Level
SL1002A
Test System
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
Product
Ultra High Density Matrix Switch Card
1260-45
Switch Card
The Astronics 1260-45 offers the highest-density switching matrices in a single-slot C-size VXI module, configurable as 11 different matrices from four 4x16 2-Wire to one 16x16 two-wire. Easily extend this module externally to build a larger matrix in a single VXI chassis to satisfy even the most dense applications.
-
Product
In-line High-Density ICT System Series 7i
E9988GL
In-Circuit Test System
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
6TL22 Off-Line Testing Platform
H71002200
Test Platform
Learn about our Build to print service for Test Platforms. The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain and cost effective. The rack is prepared for the direct integration of the three platform based receivers from Virginia Panel, the S6, G12 and G12X.
-
Product
Test Workflow Pro
test
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
Product
BMS Manufacturing Test System
Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
cPCI Card
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
OLED Lifetime Test System
58131
Test System
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Cable Free ATE
CABLEFREEATE
test
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
Product
ESD Test System
58154 Series
Test System
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
Product
Test Fixture Kits
Test Fixture
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Battery Management (BMS) Environmental Test System
Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
In-Circuit Test System Rentals
Test System
Forwessun offers flexible test system rental options to meet short-term or seasonal testing demands. Our rental systems are rigorously tested for reliability and performance, giving you access to high-quality equipment without the need for a full purchase commitment. Customised rental agreements allow you to return the equipment when it’s no longer required, providing an ideal solution for scaling up production or filling in during periods of high demand.
-
Product
Fixturing Kit
10744A
Test Fixture
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
Product
ARINC PCI Interface Card
PCI-A429
Interface Card
Alta Data Technologies’ PCI-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
PCI Express Graphics Cards With NVIDIA RTX 4000 SFF Ada
NVIDIA RTX 4000 SFF Ada
Graphics Card
- NVIDIA Ada Lovelace Architecture- Half height, half length design- PCIe Gen4x16 interface- 20GB GDDR6 Memory, 160-bit Bandwidth- 6144 CUDA Cores, 19.2 TFLOPS SP Peak- 192 Tensor Cores, 106.8 TFLOPS- 4 x mDP (mini Display Port 1.4), 1 x USB-C
