-
product
Flash Programming for Functional Test Systems
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
product
Actuation Methods for Functional Test Systems
Functional test typically applies full operational power to a final product or a loaded printed circuit board in order to determine if the Product/ PCB performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies within its Signature Series functional test fixtures.
-
product
Combined Environmental Reliability Test System
VTC SERIES
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
product
Test Gas Generation Systems
TU Series
The test gas generation systems in the TU Series include a test gas generation system for evaluating the performance of various kinds of gas sensors, as well as systems for generating simulated gases for evaluating catalysts. These systems are personally tailored to customers’ intended uses.Among the systems we offer some utilise multiple mass flow controllers to mobilize functions (e.g. to generate gases of any concentration, to add moisture, to control supplied gas pressure and to heat gases) thereby allowing for comprehensive control via a PC or PLC.A common use of this product within the biotechnology field is as an atmosphere gas supply system inside fermenters.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Test System
Maynuo Electronic Co.,Ltd a professional R & D and production of programmable DC electronic loads, programmable DC power supply, high power load, power supply, AC power supply, power supply, such as testing high-performance mobile phone test equipment and facilities, as well as electrical, electronic, aerospace, military, chemical, automotive, battery charger, battery, solar cell production lines and other industries to provide automated testing program. The company has many years experience in a number of outstanding technical R & D, product innovation by the majority of users. We are committed to provide users with more accurate and more stable more easily accessible to the higher cost of test instruments, to create the industry in testing the influence of an international brand of excellence.
-
product
Multi-Function Test & Measurement System
Optoplex’s Multifunction Test and Measurement System (TM100 Series) is designed to provide a flexible and cost effective optical test and measurement solution, particularly for manufacturing lines. The mainframe can be mounted in 19” rack or stationed on desk-top for ease of use. There are many selections of the pluggable modules, from tunable laser, optical spectrum analyzer, EDFA, power meter, ASE light source, optical tunable filter, optical performance monitor, …, etc.
-
product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
product
AirTech Test Systems
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Hillger NDT has developed AirTech testing technology for the requirements of air-coupled testing. Our USPC 4000 AirTech ultrasonic testing system and our robust AirTech sensors consisting of optimized transmit and receive probes deliver optimal results under demanding conditions.
-
product
Microindentation Hardness Testing Systems
LM Series
Perfect for a production facility or a research lab, LECO's LM Series Microindentation Hardness Testing Systems offer a variety of models (including analog and digital) with the advanced features that meet your requirements and budget.
-
product
Electronic Test And Measurement Systems
Summaries, information, & tutorials about electronics test and measurement equipment & techniques.
-
product
Thermal Stability Test System
Premier Electrosystems' Thermal Stability Test Setup is used to test thermoplastics and PVC (Plasticized Polyvinyl Chloride) materials. When exposed to continuous heat, these materials degenerate and emit harmful acidic gases. The instrument is manufactured for testing PVC materials for their thermal stability at higher temperature.
-
product
BMS Test System
6020
High Extensibility: for multi-string battery cell, 4 cells per channel, expandable from 1 to 16 cells per strings
-
product
Digital Logic ICs
Renesas' general-purpose logic devices support the information equipment and computer fields, which demand small size and high performance. With a variety of power supply voltages, functions, and capabilities, these logic devices provide strong support for specialized applications such as bus switching, level conversion, and clock-related applications.
-
product
Test System
USB Explorer 280
The Ellisys USB Explorer 280 is a sophisticated protocol test and analysis system for USB SuperSpeed traffic monitoring, driver and software stack debugging, and performance analysis.
-
product
AIM System Solutions
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
CRPA Test System
The Spirent CRPA Test System is a development of Spirent’s GSS9000 Series platform for testing Controlled Reception Pattern Antenna (CRPA) systems with a separate RF output per antenna element. The CRPA Test System generates both GNSS and interference signals. Users can control multiple antenna elements. Null-steering and space/time adaptive CRPA testing are both supported by this comprehensive wavefront approach.
-
product
GSP-2B Test System Interface Probe
GSP-2B
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 125Recommended Travel (mm): 3.18Overall Length (mil): 845Overall Length (mm): 21.46
-
product
Protective Relay Test System
MTS-5100
The MTS-5100 is the only all-in-one relay test set with a direct front panel interface for all functions, without exception!
-
product
Ice Point Calibrators
These ice point calibrators are designed to accurately calibrate probes at the freezing point of water. These devices have multiple thermowells to calibrate multiple sensors simultaneously.
-
product
Count Down Test System
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
-
product
Portable Test System
MT786
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
product
SoC Test System
V93000 SoC / Smart Scale
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
-
product
VLF Testing and Diagnostics System
PHG 80 TD/PD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 80 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltage* Compact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
product
Optics Test Systems
Lens Test
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
product
System Tests Radar Pulse Stability
PN9002
Noise eXtended Technologies S.A.S.
The cost-effective PN9002 test simplifies the testing and analysis of pulse-to-pulse amplitude and phase stability for radar systems and components to 18GHz.
-
product
Belt Starter Generator Test Systems
D&V has developed 12 V, 48 V and higher voltage BSG and ISG testing systems for performance, endurance and production testing, complete with thermal chambers, chillers and assembly lines.
-
product
Instrument Transformer Test Systems
Our systems for testing voltage (VT) and current (CT) instrument transformers are conceived among other things for testing accuracy and insulation.
-
product
Shock Test System
Labtone Test Equipment Co., LTD
Products are inevitably affected by impact, bump, free fall, tumbling etc. during production, transportation, loading and unloading as well as during the use of the products. All of these are transient excitation on the object, causing the object to produce mechanical characteristics of high speed, acceleration, strain rate instantly. These kind of characteristics are completely different from that in static load, and may cause problems to the object in terms of structural strength and stability and sometimes the object may fail. Therefore, it's necessary to study the effect of impact and reproduce the shock environment, to assess the structural strenghth and performance of the object under shock environment.
