Plugs
A male connector.
-
Product
Magnetic Plugs
-
Magnetic Drain Plugs were pioneered by Lisle Corporation in the 1930's. Lisle MAGNETIC PLUGS are similar to standard pipe or straight thread drain plugs with one important difference – a permanent magnet is fastened to the plug body. This magnet attracts and holds abrasive, ferrous metal particles preventing their circulation through the lubrication or hydraulic system.
-
Product
EPON OLT ( Optical Line Termination )
OLT-1408
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OLT-1408's Optical Line Terminal (OLT) adopts GiGA Ethernet Passive Optical Network (EPON) technology. It is a compact chassis with L2/L3 GiGA switching and routing function. All the functional components are modularized design and it supports hot-plugging with plugging and playing. 1~4 pieces of GiGA optical port or electrical port are optional in the uplink port, which provides a direct optical interface for the Ethernet/IP network core. 1~8 pieces of EPON optical port are optional in the down link port. Through a passive optical Network (PON), an optical Network unit link (ONU),it can provide final transmission with bandwidth up to 1Gbps for the user.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Single-ended, Direct Connect Probe, 34-Channel, 4 X 160-pin
U4206A
-
The U4206A is a direct-connect probe/cable with a standard soft touch pro connector at one end that routes to four 160-pin connectors that plug into the front panel connectors of a U4164A logic analyzer module. The U4206A is designed to be used with either the quad state mode or ¼ channel 10 GHz timing mode of the U4164A logic analyzer module. For use in quad state mode only, the U4206A includes two flying leads to connect additional clock qualifier signals into the clock inputs on Pods 3 and 7. Please refer to the U4164A installation guide for specific details on the operation of the U4164A quad sample state or ¼ channel 10 GHz timing modes of operation.
-
Product
CMOS Camera
ISH1000/ISH500/ISH300
-
Fuzhou Tucsen Photonics Co.,Ltd
ISH1000, ISH500 and ISH300 belong to Tucsen professional camera H series is a new generation of Tucson scientific CMOS camera, the effective pixel are 1000 million, 500 million and 3 million. They provide a strong plug and play support, easy to operate, and with powerful imaging software, you are a good choice for laboratory teaching, medical industry and other fields.
-
Product
Wireless Adapters
-
A device that can be plugged into a USB port to enable wireless access from a computer to an external Wi-Fi device, as a mobile phone, or to the Internet, via high-speed broadband, or to enable wireless connectivity in a printer or other peripheral.
-
Product
Versatile 5-Channel Industrial Amplifier/ Conditioner Instrument
MODEL TIO-3000
-
The TIO-3000 System was originally designed to perform precision summing on 2, 3 , or 4 load cell signals for weighing applications. Development has progressed into accessory modules with considerable versatility for user defined configurations in a compact economical five (5) slot system with built-in meter and channel selector. Please see below for more information on the four available plug in modules and for available system configurations.
-
Product
PXI/PXIe Power Relay Module, 5 Amp, 50-Pin D-type Connector, With Interlock
40-158-103-HI
-
The 40/42-158-103-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
Ten Foot Test Leads w/Screw On Alligator Clips
629-10
-
After numerous requests, we are introducing 10 foot version of our popular 629 test lead. This test lead is 10 feet long, with no connectors or reels. This test lead can be deployed for various applications involving the need for a longer reach. Also, there are no connectors or extension plugs to snag, catch or scratch any part of the vehicle.
-
Product
Coax, Patchcord, Receiver, 36", Micro Coax, RG316 Double Shield Tan, SMB Plug
7-368117652-036
-
Coax, Patchcord, Receiver, 36", Micro Coax, RG316 Double Shield Tan, SMB Plug.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
PXI Remote Control Interface Module
41-924-001
-
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, this PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
Product
Tone Test Set
240 Weathertite
-
The AINES Model 240 Tone Test Set is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
3 Digit LCD Voltmeter
DPM 500
-
The DPM 500 is a 3 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV d.c. full scale reading, auto-zero, auto-polarity and a set of annunciators. The meter plugs directly into a DIL socket or can be panel mounted using the snap-in bezel and window.
-
Product
SparkFun Breadboard Power Supply 5V/3.3V
-
Here is a very simple breadboard power supply kit that takes power from a DC wall wart and outputs a selectable 5V or 3.3V regulated voltage. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled VCC and GND plug directly into the power lines. The lone pair of pins have no electrical connection but help support the PCB.
-
Product
50Ω UWave SMA Cable Assembly, 26.5GHz, 0.1m
40-977-542-0.1m
-
50 Ohm uWave SMA Plug to uWave SMA Plug Cable Assy, 26.5GHz, 0.1m Long.
-
Product
0 to 1000 ppm CO Measurement Range
EL-USB-CO
-
The EL-USB-CO is a USB data logger that measures and stores up to 32,510 Carbon Monoxide (CO) readings over a 0 to 1000 ppm measurement range. The user can easily set up the logging rate and start time, and download the stored data by plugging the module straight into a PC's USB port and running the purpose designed software under Windows 2000, XP or Vista
-
Product
PXI/PXIe Power Relay Module, 50xSPST, 5 Amp, 50-Pin SGMC Connectors, With Interlock
42-153-001-HI
-
The 40/42-153-001-HI is a PXI/PXIe high density power relay module with 50xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
DIESEL COMPRESSION ADAPTER FOR FORD AND INTERNATIONAL
DTC1524
-
*M14 x 1.25 thread adapter attached to hose and a quick disconnect*Screws into the head of the engine in the glow plug hole*Use on International VT 365 engine used in the International 4200 medium-duty truck and Ford Powerstroke 6.0L used in the Ford F250-F550 trucks
-
Product
3 Digit LCD Voltmeter
SP 200
-
The SP 200 is a 3 digit LCD voltmeter with 9mm (0.36") digit height and LED backlighting. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into two 6-way SIL sockets and can be fitted into a panel via the fixing clip.
-
Product
Tone Coax Cable Generator
240 HAL
-
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
Portable GPU empowered by NVIDIA RTX A500
Pocket AI (EGX-TBT-A500)
-
Pocket AI offers the ultimate in flexibility and reliability on the move. This portable, plug and play AI accelerator delivers a perfect power/performance balance from the NVIDIA RTX GPU. Pocket AI is the perfect device for AI developers, professional graphics users and embedded industrial applications for boosting productivity by improve the work efficiency.
-
Product
BNC Male to BNC Male Cable, 75 Ohm, 2 m (Quantity 4)
779697-02
-
The BNC-BNC Coaxial Cable, sometimes referred to as BNC Plug to BNC Plug, connects measurement and signal devices.
-
Product
USB Modular Source Measure Unit
U2722A
-
The U2722A USB Modular Source Measure Unit is a 3-channel 20V/120mA that can operate in a 4-quadrant operation. The channels could be connected in series or in parallel to achieve up to 60 V/360 mA. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
Product
34945EXT Distribution Board, For Two 87104x/106x L7x0xx Multiport Or 87406B Matrix Switches
Y1151A
-
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
BNC Twinax Connectors
-
BNC Twinax connector category has several part numbers, the majority are RoHS and REACH compliant. BNC Twinax connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC Twinax connectors are built to precise industry specifications. Pasternack BNC twinax connector items are available in jack or plug gender with 78 Ohm impedance. Connectors in twinaxial BNC are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These BNC Twinaxial connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this twinax BNC connector series is in-stock. In addition to being in stock, these twinaxial BNC connectors will ship the same day as they are purchased.
-
Product
12 Block Desktop Receiver
VGR12
-
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
USB Modular Multifunction Data Acquisition
U2300A Series
-
The U2300A Series USB Modular Multifunction Data Acquisition family consists of 7 modules - ideal for design validation and manufacturing engineers who conduct data logging, measurement or monitoring in a broad range of industries. All modules use the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity and comes bundled with the Keysight Measurement Manager (AMM) software. The U2300A series can function as a standalone or modular device that plugs into the U2781A USB Modular Product Chassis. These are also compatible with a wide range of application development environments such as Keysight VEE Pro, MATLAB2007a, NI LabVIEW and Microsoft Visual Studio. Get Keysights quality products at a low price.
-
Product
SparkFun Analog MEMS Microphone Breakout
SPH8878LR5H-1
-
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield.
-
Product
Cable Assembly, Receiver, 20/26GHz Coaxial, 20", 8 SMA Plugs
540259010153
-
Cable Assembly, Receiver, 20/26GHz Coaxial, 20", 8 SMA Plugs
