Plugs
A male connector.
-
Product
Waspmote Plug & Sense! Encapsulated line
-
Libelium Comunicaciones Distribuidas S.L
Robust waterproof IP65 enclosure.11 models integrating more than 150 sensors.Add or change a sensor probe in seconds.Solar powered with external panel.Radios: 802.15.4, 868, 900, WiFi, 4G, Sigfox and LoRaWAN.Over the Air Programming (OTA).Special brackets ready for street lights installation.Fully certified for the main markets: CE, FCC, IC, ANATEL, RCM, PTCRB, AT&T.
-
Product
Bus Analyzer / Exerciser
VME850P2
-
The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.
-
Product
AC Power Supply
FC5003
-
Behlman’s FC5003 is a ruggedly built, COTS frequency converter designed to convert 120/208 VAC, 3-phase, 60 Hz, ground power to 115/200 VAC, 3-phase, 400 Hz, aircraft power. The FC5003 is in a rugged 6U (10.5”H) 19 inch rack mount chassis with an input line cord with plug and an output receptacle.
-
Product
Power Tester
PS-228
-
The product designs with LCD to show ATX power voltage. Easy to plug with ATX power 20/24 pin and plug in (P4/P6/P8) to show the voltage on the LCD panel.
-
Product
SAX Test Block & PAX Probes
-
The SecuControl SAX is a versatile, space-efficient, and two-in-one terminal and test block that brings safety and consistency to substation testing. Its finger-safe design, keyed PAX/STP plugs, make-before-break operation and built-in CT shorting deliver reliable secondary injection without wiring changes or open-circuit risks. Ideal to modern substations where speedy deployment and simplicity are key.
-
Product
18 Inch Universal Flex Current Probe Accessory
FLIR TA74
-
The FLIR TA74 adds capabilities, simplifies challenges, and gives you the best readings with your existing meter. The narrow, 18-inch long flexible coil clamp and locking mechanism allows you take measurements in tight or awkward spots – ideal for multiple conductor measurements, double-wrap requirements, and deeper access. The connection is a standard banana plug and the output is a voltage signal, so it’s compatible with most DMMs and clamp meters, regardless of brand.
-
Product
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 7-Pin DIN and 4 Banana Plugs
540078010111
Cable Assembly
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 7-Pin DIN and 4 Banana Plugs
-
Product
Plug and Switch Testing
-
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right.
-
Product
PCB Adapters - TriPaddle
-
TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.
-
Product
DMM Test Probe Kit With Multi-Stacking Banana Plug
5325A
-
DMM test probe kit with multi-stacking banana plug
-
Product
Data Logger for Temperature and Humidity
DSR-THEXT
-
Using external compact probe especially for HVAC application to measure and log temperature and humidity data inside pipes with minimal invasion Support screen and audible alarm Original fittings for sensor connection, ensures 100,000 plugs Suitable for HVAC, agriculture research, plants and animal growth monitoring and other applications
-
Product
Cable Assy 78-Pin D-Type Female to 32 x Mini Thermocouple Plugs
A078DFR-32M002T5A100
Cable Assembly
This 78-pin D-type thermocouple cable assembly is terminated with 32 male mini thermocouple plugs. It is constructed from 7/0.15 (26AWG) silver plated copper wire and screwlocks are provided to secure the D-type to its associated products.
-
Product
PCB Adapters
-
Signal PCB AdaptersQuadraPaddle & TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.VTAC SIM PCB AdaptersVTAC Snap-in-Module adapters provide flexibility and modularity where custom PCBs cannot. Mix and match small modular boards to create a custom solution. Move SIM PCB adapters around to optimize space, mix protocols and match with standard patchcords. Combine protocols in a VPC SIM module and swap boards as your requirements change.
-
Product
Automotive Current Tester LCD Display
77102
-
This automotive current tester with LCD display, plugs directly into the fuse box and can be used on mini, standard and maxi fuse connections. Blades may get hot during use and care should be taken for 2mins whilst they cool down. Fits mini and maxi fuses. Current range 0-80AMP. Safe and easy way to check automotive current.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin D-type Connector, With Interlock
42-153-103-HI
Relay
The 40/42-153-103-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
Torque Sensors
-
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
-
Product
Multi-Modular Cable Tester
3PK-NT005N
-
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
Product
Cannabis HPLC With Autosampler
-
Award-winning, simple-to-use HPLC suitable for those without prior laboratory experience or science background, as well as professionals & commercial labs alike. Addition of our plug&play autosampler makes the HPLC suitable for high throughput commercial analyses of cannabis samples.
-
Product
PXI 10A Power MUX, 5-Bank, 6-Channel
40-661-005
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
MIL-STD-1553 A / B Test And Simulation VXIbus Module
VXI-1553
-
*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
USB-C® – USB 2.0 Receptacle HS SQ Test
AUT17037
-
This product is designed for USB-C USB2.0 Plug Host/Device Electrical Test.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
x1 to x16 PCI Express Riser
SKU-074-01
-
x1 to x16 PCI Express Riser (Riser) allows to plug in any downstream PCI Express board (x1, x4, x8, x16) to the upstream x1 PCI Express connector.Riser has two support tabs for mechanical stabilization of add-in PCI Express board (US Patent 7,255,570) and PCI Express retainer (US 7,850,475) that securely holds Riser inside upstream PCI Express connector.The Riser functions right out of the box, no additional software needs to be installed.
-
Product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
Product
Fracture Mechanics Clip-On Gages
Model 3541
-
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Expansion I/O Module.
SI-MOD66xx
-
The SI-MOD66xx is a family of high resolution, multi function data acquisition and control modules that plug into any SI-CxDSP carrier processor card for the PCI bus.
-
Product
400 Watt DC/DC Converter, 3U VPX, Holdup Time
VPX68
DC Converter
NAI's VPX68 is a rugged and high-efficiency 400-Watt Output +28 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply with optional integrated Holdup Time that plugs directly into a standard VITA 62 conduction cooled chassis. The power supply, engineered to meet harsh environmental conditions, includes continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
Product
Universal Carrier Board
UCB
-
All function modules are plugged into our Universal Carrier Board (UCB) – with four slots available per carrier.
-
Product
Socket Testers
-
Precision Mastech Enterprises Co.
Handheld electrical tools plugged directly into wall outlets to quickly verify if they are wired correctly and functioning safely.
-
Product
E-DRIV® Electric Screwdrivers
E-Series
-
The electric screwdriver is for light duty tightening applications. The assembly tool plugs directly into a power outlet and does not require a separate power supply unit. Ensures accuracy in fastening with precision automatic shut-off clutch once preset torque is achieved. Operates on a duty cycle of 0.5 seconds on and 3.5 seconds off.
