Plugs
A male connector.
-
Product
Electronic Compact Pressure Switch (Pallect Pressure Switch)
PPE
-
mm.A compact trimmer setting type, three types of piping connections (R1/8, Φ6 plug, Φ6 one-touch fitting) and a dustproof/waterproof structure allow for flexible use.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
-
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Cable Assembly, Receiver, 20", Mini Power, 19 Pin to 4 Banana Plugs
540067010108
-
Cable Assembly, Receiver, 20", Mini Power, 19 Pin to 4 Banana Plugs.
-
Product
Acoustic Emission Testing Equipment
1283 USB AE Node
-
The 1283 USB AE Node is a full-featured, low-cost Acoustic Emission testing equipment that plugs conveniently into and is powered by the USB port of a user’s PC or laptop to maximize portability and versatility.
-
Product
Osprey PCI Unibus Adapter
9793
-
Dual-height card plugs into PDP-11 Unibus backplane. Fibrechannel cable plugs into Unibus logic connector on Osprey /TXP I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
Product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
SparkFun Serial Basic Breakout
CH340C And USB-C
-
This SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340C and takes advantage of the handy USB-C connector. With USB-C you can get up to three times the power delivery over the previous USB generation at 1.5A and and also solves the universally frustrating dilemma of plugging a USB cable in correctly, because it’s reversible! The Serial Basic works with 5V and 3.3V systems and possesses the capability to auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340C IC to quickly and easily convert serial signals to USB.
-
Product
High-Low Circuit Tester
29500
-
The low-side checks AC and DC current up to 28 volts with power on. The high-side checks spark plug wires without piercing. Complete with insulated clip.
-
Product
Terminal Test Kit (19 PCS)
3605
-
Peaceful Thriving Enterprise Co Ltd
1. Check high and low voltages (power and ground) on 6, 12 and 24V system.2. 4mm connection for banana plugs.3. LED indicates red for power (high) and green for ground (low).4. High impedance protects sensitive electronic ignition components.5. Connects red lead to power source and black lead to ground source.6. 1.8m long heavy-duty dual leads with battery clips and spring strain relief.7. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
Product
MATCO BASIC MULTIMETER
MD251
-
*Provides readings for volts, amps and ohms required for automotive electrical system tests, as well as diode and continuity tests*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
Product
18 Pc. Micro 64 Test Connector Kit
147
-
Test connector kit featuring a variety of terminal adapter sets which enable connection to Micro64 terminals - primarily found on GM vehicles and some EU/Asian/Domestic vehicles. Adapters connect via the included 48 inch stacking banana plug test leads. Connection to most DMM’s and scopes is no problem. Kit is designed to provide a quality & secure test connection while quickening the test process.
-
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Torque Sensors
-
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
