Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
Wheel Running Tester up to 15000 kg axle load
MINC II EURO | VP 420005
-
Maschinenbau Haldenwang GmbH & Co. KG.
The test lane-compatible MINC II EURO guarantees a verification of the axle geometry in seconds when the test vehicle drives over (up to 15.0 t axle load) as well as a fully automatic evaluation of the deviation in m / km. The measured values are displayed either in analog form on a dial or by transmission to a PC screen (including graphic representation).
-
Product
PXI Mixed Configuration Relay Module - 13 Cells Populated
40-138-AA-BB-CC-DD (13 CELL)
-
The 40-138 2A Relay Module with 13 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Water Filler for Nickel-Cadmium Cells
MasterFiller
-
The MasterFiller is an instrument designed to deliver measured quantities of distilled water as required in the service of Aircraft Nickel-Cadmium batteries.· The MasterFiller consists of a microprocessor controlled pump with a level sensing probe, a keypad and display and an external 12VDC power supply (or optional battery).· The MasterFiller is part of a system comprising Intelligent Charger-Analyzers and Software for Battery Data Acquisition and Analysis, designed to improve the accuracy and efficiency of the process of testing batteries for airworthiness certification.
-
Product
Compression Load Cells
-
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
The Imperas Instruction Set Simulator
ISS
-
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
-
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Fuel Cell Test Stations
-
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
-
Product
Cell Balancer
-
The Maccor Cell Balancer is a cutting-edge device designed to charge and discharge individual cells in a string (battery pack) simultaneously. Each cell balancer can handle up to 8 cells, and by using multiple balancers in series, larger battery packs can be balanced effectively. Maccor's innovative 'Mactest32.exe' software includes integrated cell balancing features, empowering users to incorporate cell balancing steps seamlessly into their test procedures.
-
Product
AC Load Bank (Resistive/Reactive)
K-1000 Resistive/Reactive
-
Kongter Test & Measurement Co., Limited
Resistive/reactive load banks are great choices for testing turbines, switchgear, rotary UPS, generators and UPS systems. They can also be used for integrated system testing of utility substation protection systems, particularly for more complex relays like distance, directional overcurrent, power directional and others. A resistive/reactive inductive and/or capacitive load is often required to test solar inverters to ensure solar panels can be stopped from producing electricity in the event of a power outage.
-
Product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
Product
Power Supplies And Loads
-
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
Stimulus Test Cell
HA7300
-
The Stimulus Test Cell HA7300 is a test cell which provides an environment for high-speed, highly accurate temperature and pressure test of differential pressure sensors, utilizing Advantest’s unique temperature control unit with simultaneous temperature control for 8 devices, as well as a newly developed 2Port pressure controller and pressure application nozzle.
-
Product
High Power LED DC Electronic Load
33430G Series（1800W / 3600W）
-
Each 33430G Series has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, panel with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
Product
Generator Loading System
-
Mosebach Manufacturing Company
GLS (Generator Loading System) is a load bank for use with your generator to load it automatically to your set point. This will keep your generator running at its optimal point and reduce your maintenance costs. Fully programmable by you.
-
Product
Carbon Pile Load Tester 500 AMP
6034
-
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
Product
Solar Simulation
-
Sciencetech solar simulators produce high intensity, uniform illumination on a target area. Typically, high power solar simulators use an ellipsoidal reflector to capture light from an arc lamp source inside the reflector, an arrangement that results in a light pattern with a bright outer region and a dark center. This non-uniformity is un- acceptable in many solar simulator applications and as a result, forces many of our solar simulator competitors to use designs involving diffusers to reduce the non-uniformity. This results in a reduction of intensity and a dis- tortion of the spectrum on the target area.
-
Product
Personal Workstations for Load Ranges up to 440 lbs.
9200 Series
-
The 9200 Series Vibration Isolation Workstation is a smaller, more compact design providing affordable personal convenience. The 9200 is ideal for applications such as Balances, Optical Microscopes, Cell Injection, Roundness Checkers, and Surface Profilometers.
-
Product
MIL-STD-1553 USB & LAN Test & Simulation Module
UXI-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
Product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
-
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
Product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
-
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Low Concentration Photo-Voltaic (LCPV) & High Concentration Photo-Voltaic (HCPV) Cell Testing
-
Concentrated PV Cell testingPhoto-biological studies of plants, animals, and cell culturesSemiconductor testingPhoto-toxicity researchMaterial degradation researchAccelerated UV and solar exposure testing of color fastness and material stability for paints, textiles and plasticsAtmospheric photochemical pollution research
-
Product
Solar Simulator
Unisim Compact Solar Simulator
-
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system.As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability.The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available).The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter.Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
Electronic Loads
SLM DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
UE Simulator
-
With Simnovus, you get superior value as our software runs on COTS and SDR enabling you to deploy multiple test beds. You do not have to spend millions on expensive Capex.
-
Product
Radiator Mount Load Banks
-
Mosebach Manufacturing Company
Help prevent wet stacking in diesel gensets with a radiator or duct mounted load bank. Being a supplemental load, Mosebach has a solution to fit your needs.
-
Product
Battery Load Banks
-
Kongter Test & Measurement Co., Limited
Kongter offers many different models of battery load units for real capacity test in various industries. With our customized solution, users of different applications will find their exact models as per their needs. With its optional DAC (Data Acquisition Case), you could easily monitor voltage of each cell on PC during battery discharge test.
-
Product
Resistance Temperature Detectors (RTD) Simulators
-
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
Product
PXI Mixed Configuration Relay Module - 2 Cells Populated
40-138-AA-BB-CC-DD (2 CELL)
-
The 40-138 2A Relay Module with 2 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
