Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
External Load Expansion Connector Accessory for USBHub3c
-
Used for connecting external electronic loads to the USBHub3c for VBUS load testing. It features separate screw terminals for VBUS passthrough from each USB Type-C port (0 through 5). While this board provides a physical wiring interface to access each VBUS channel, the USBHub3c External Load Feature is required to enable VBUS outputs on the USBHub3c.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
OBD2/J1708/J1587 Simulator
DFLSOBD2
-
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
Product
Electronic Load Device
786530-01
-
The RMX-4004 provides capabilities for qualifying power designs and validating power supply functionality in a production environment. You can combine Electronic Load Devices to customize your test system based on the number of channels, maximum load power, and voltage and current of each channel.
-
Product
Solar Cell Tester
-
Jiangsu Keyland Laser Technology Co., Ltd.
Features:- Up to standard IEC60904 & JISC8933- 24 hrs continuous working , over 300,000 flash- Siemens PLC system adopted- 10 Parameters display
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
-
Product
Solar Cells and Modules Online Measurement System
PV-LIT
-
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
Product
Autonomous Vehicle Simulation
-
Ansys Autonomous Vehicle Simulation provides a solution designed specifically to support developing, testing and validating safe automated driving technologies. This autonomous vehicle simulation solution saves significant time and costs versus traditional development and testing methods by allowing you to exercise your AV/ADAS software stack in a closed loop, with sensor-accurate synthetic data in software-in-the-loop or hardware-in-the-loop context with the driving simulator of your choice.
-
Product
Electronics Cooling Simulation Software
FloTHERM
-
Perform thermal analysis, create virtual models, and test design modifications of electronic equipment before physical prototyping. FloTHERM uses advanced CFD techniques to predict airflow, temperature, and heat transfer in components, boards, and complete systems, including racks and data centers. It''s also the industry''s best solution for integration with MCAD and EDA software.
-
Product
ACARS CMU Simulator
-
Square Peg Communications Inc.
The SPCI CMU Simulator replaces the ACARS Communications Management Unit for end-to-end testing of the ACARS system. It communicates with an Inmarsat Classic Aero or SB-Safety Satellite Data Unit (SDU) via ARINC-429 to generate and receive ACARS traffic. The CMU Simulator is implemented as a Physical Layer Tester script, and can run on either a BPLT or a GDU. In addition, it can run on a standard PC using a special version of the GDU or BPLT software. In all cases, a suitable ARINC-429 interface must be present.
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
PCB Simulation Solutions for High-Performance Designs
HyperLynx
-
HyperLynx® offers a complete suite of analysis and verification software that meets the needs of PCB engineers at any point in the board design flow. Easy to use and integrate into your flow, HyperLynx equips PCB engineers to efficiently analyze, solve and verify critical requirements to avoid costly re-spins. Achieve greater innovation, faster time-to-market and decreased costs with HyperLynx.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
-
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
S-Type Load Cells
-
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
Product
Crash Simulation Systems
-
The crash simulators are capable of reproducing a wide range of standardized and user-defined crash tests including advanced applications such as side impact and vehicle pitch simulation. Instron’s acceleration sled systems are used for the development and approval of vehicle safety systems, vehicle parts and also for the investigation of solids and structures during crash events.
-
Product
Concurrent Alternative RF & GNSS Signal Simulation
SimAltNav Replay
-
Non-GNSS sources of RF (radio frequency) are of interest in GPS-degraded or contested signal environments, with interest focused on LEO (low earth orbit) constellations. These systems offer high receiver signal power (relative to GNSS) and a secure & resilient link to augment GNSS.
-
Product
Regenerative Grid Simulators 9kVA-15kVA
-
Chroma Systems Solutions, Inc.
Four quadrant, single- or three-phase AC power sources designed to simulate real-world grid characteristics for EV, PV inverter, and smart-grid test applications.
-
Product
2 Port BRI-S/T ISDN Simulator PCI
BRI-2ST-PCI
-
The most inexpensive ISDN simulator on the market. Designed in standard PCI card form factor it has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
Product
MULTI-STANDARD LOCAL LOOP SIMULATOR
458-LM-A8-30
-
Accurately simulates attenuation and impedanceFull bidirectional operation at all specified frequencies26 AWG PIC as specified in ANSI T1.417
-
Product
Power System Simulator
F6150sv
-
This power system simulator performs the simplest through the most complex tests. The F6150sv has the highest output current of any test set on the market – all within a single box.
-
Product
Vector Network Analyzer (VNA) Simulator – Standard
S94050B
-
S94050B puts flexible S-parameter analysis into your own computer. Dive deeper into measurements captured on a network analyzer or develop and optimize test programs before deploying them onto an instrument.
-
Product
Basic Rate ISDN and IDSL Network Simulator
Emutel Solo
-
Emutel Solo is a small, portable lightweight battery powered basic rate ISDN and IDSL network simulator. With 2 software switchable S/U interfaces and the choice of either Euro-ISDN, North American or NTT support. Emutel Solo allows you to test and demonstrate all types of BRI equipment on one compact unit. Providing all the standard features but also many others that its compeditors don't include.
-
Product
Simulation Table
KRD61 6-DOF
-
KRD61 series 6-DOF simulation table is a closed-loop servo simulation platform consisting of six servo actuators and six sets of dedicated hinges connected at the top and bottom platforms respectively. By virtue of the telescopic movement of the six actuators, the upper platform moves in six degrees of freedom (X, Y, Z, α, β, γ), so various space motion attitudes can be simulated.
-
Product
Load Cabinet
DFX-20
-
• Working power: AC220V 50Hz • Normal load: Continuous adjustable from 0 to 280V • Electric current: 0～20A/Continuos adjustable cosφ: 0.3-0.96 under 16A; 0.6~0.96 more than 16A • Precision: 0.5 class, digital display • Counter: 0～999999 times, can be preset
-
Product
Cell Testing
-
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
Product
Test Cells
-
Our test cells accurately characterize the dielectric properties of liquids and solid material.
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
