PCI Backplanes
-
Product
STANAG3910 Test And Simulation Module – Rafale – For PCI Express
APEX3910-EN
Simulator
Single Stream STANAG3910 Test and Simulation module – Rafale – for PCI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE). The APEX3910-EN is a functional replacement for APE3910-EN.
-
Product
Flexible 32-bit PCI to MiniPCI Express Adapter
SKU-057-0X
-
The Flexible 32-bit PCI to MiniPCI Express Adapter (Adapter) was designed to convert the 32-bit PCI bus into a MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion board to the motherboard PCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), 32-bit PCI host board and PCI Express flat cable.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 11.4MΩ
50-298-053
Programmable Resistor Module
The 50-298-053 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm - SPST
50-294-111
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Test & Simulation Interface for PCI
PCI-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows
778032-01
Interface
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131 Ohm With SPDT
50-293-134
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785594-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Digital Signal Processor Card for PCI bus
SI-C33DSP
-
The SI-C33DSP-PCI from Sheldon Instruments is a powerful Digital Signal Processor (DSP) card for your PC equipped with a PCI bus. It is based on Texas Instruments’ new 150Mhz TMS320VC33, 32 bit floating point DSP, and can transform your PC into an ultra high performance development system and DSP accelerator.
-
Product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
Controller
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
81 lane, 21 port, PCI Express
PEX 9781
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
PCI-5114 , 125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device, 8 MB
779745-01
Oscilloscope
125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device—The PCI‑5114 low-cost oscilloscope device has two channels that sample up to 250 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 102kΩ
50-298-034
Programmable Resistor Module
The 50-298-034 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786164-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
Product
(Compact PCI) GPIB Controller Card
Model 488-PXI
Controller
* Adds GPIB Controller capability to any PXI or Compact PCI System.* Fast >1 Mbs transfer rate* 488.2V4 Driver supports 32 and 64-bit Windows XP, Vista, Windows 7, 8 and Windows 10 with a true 64-bit DLL.* Compatible with industry standard 'ib' and '488.2' command sets.* Works with Agilent, NI and Kikisui VISA libraries.* ICS's Explorer auto configures your controller as it finds your instruments.* Program with Visual Basic, C, LabVIEW, Matlab or Agilent VEE* Most affordable PXI-GPIB controller card available.
-
Product
16-Lane, 10-Port PCI Express
PEX 8717
-
The ExpressLane™ PEX8717 is a 16-lane, 10-port, PCIe Gen3 switch device developed using 40nm process node. PEX8717 offers PCI Express switching capability that enables users to create up to 9 downstream ports with varying widths including native x2. Today's processor south bridges offer x1 or x4 PCIe lanes, where x1 often does not provide enough bandwidth and x4's sheer size could waste valuable PCIe lanes.
-
Product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
-
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
Product
PCI To PCI Express Board
MS 1718
-
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Product
PCI Express 4 CEM Receiver Test Automation
N5991PC4A
-
The N5991PC4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 4.0 CEM Add-In Cards and systems
-
Product
PCI 16 Reed Relay Output / 16 Isolated Input Digital Interface (10-30V)
8004H
-
Optimized for sensing up to 24V inputs, the 8004H PCI digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The inputs protect the computer equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. The relays are normally open, and close when energized.
-
Product
Full-Size PCI Express Mini Module With SATA
AX92907
-
*Two independent SATA channels*Fully compatible with SATA revision 2.0 and 3.0 hard drives (HDD) and Solid State Drives (SSD)*Supports RAID 0,1*Two SATA power connectors with +5V*51 x 30 mm
-
Product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB205
-
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
Product
CompactPCI Serial 3U Backplanes / Power connector
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to the PICMG CPCI S.0 CompactPCI Serial specification. This backplane features 1 power slot in addition to either 6 or 9 cPCI serial slots.
-
Product
High Speed And High Resolution Cameras (PCI Cameras)
XiB
-
*High speed interface with bandwidth of 20 GBit up to 64 Gbit / sec*CMOSIS / ams sensors: CMV12000, CMV20000, CMV50000*High image resolution and high throughput with 12 Mpix, 20 and 50 Megapixel*Speed of 133 - 333 Fps, 33 and 30 Fps respectively*Fast speed models with 1 Mpix at 3500 and HD at 2500 Fps*Robust PCI Express and Power/GPIO connectors*Integrated Canon EF-mount control with dynamic aperture and focus control*Support for Windows, macOS, Linux, ARM*Suitable for OEM customization and Embedded vision systems*Distances up to 300m over fiberoptic cable*Compact housing: 60 x 60 x 38 mm
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω To 62.1Ω
50-297-011
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm With SPDT
50-293-114
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Card
EXC-4000PCI/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M4K1553PxS module is NOT compatible to the M4K1553MCH module.The EXC-4000PCI/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
