PCI Backplanes
-
Product
PCI Very High Density Multiplexer, 99-Channel, 2-Pole
50-670C-022-99/2
Multiplexer Module
The 50-670C-022-99/2 is a 99-channel, 2-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PCI To CPCI Or PXI Extender Board
MS 1720
-
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
Product
PCI Counter/Timer with Quadrature
APC482
-
Several models with a variety of configurations provide up to ten counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths, periodic rates, or quadrature position and monitoring operations.
-
Product
14-Slot 32-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6014R
Backplane
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- PICMG 2.7 Dual system Bus specificationR1.0 compliant- One system slot with 13 expansion slots, system on the middle slot of the backplane
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
PCI High Density Matrix, Single 22x8 1-Pole
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
Low Profile PCI 24 Channel TTL Digital Interface
8018
-
The 8018 Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
12 lane, 5 port, PCI Express
PEX 9712
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
PCI Mezzanine Card
PNIC1G
Ethernet Interface
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
Product
PCI Express Ultra-fast Data Acquisition Add-In Cards
-
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ZIO Module With Four COM Ports And One PCI Express Mini Card
AX93262
-
*Specification: 2 x RS-232/422/485, 2 x RS-232, 1 x PCI Express Mini Card*Dimension: 80 x 55 mm*Accessory: 2 x COM with bracket cable*Compliant Product: CAPA840, CAPA843, CAPA880, CAPA500, CAPA313
-
Product
PCI to Star Fabric Module
51-921-001
Remote Control Interface
This module resides in the Slot 1 position of a PXI chassis and interfaces to the backplane of the PXI chassis. When located in a generic peripheral slot, it can be used to drive two extension PXI chassis.
-
Product
3U OpenVPX 2-Slot Backplane With 1 VPX Power And Ground Plus 1 VITA 62 Power Supply Slot
101VPX302-xxxx
-
This 3U Open VPX backplane offers one VITA 46 Power and Ground slot and one VITA 62 power supply slot to support the development and deployment of systems requiring a VITA 62 power supply. The rear power studs can be used to connect to an adjacent backplane to feed it power.
-
Product
PCI Reed Relay Card, 32xSPDT
50-110B-021
Reed Relay
The 50-110B-021 is a 32xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
16 Channel ADC for PCI
PCI392
-
The PCI392 16-Channel Common-Mode Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality like calibration. User-specific functions can be added for customized operation.
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786167-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
-
Amfeltec Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
-
Product
64-bit PMC to PCI Adapter
4930
-
This passive PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment.
-
Product
7-Slot 3U OpenVPX Backplane Aligned To SOSA | 6 VITA 65 Slots + 1 VITA 62 PSU Slot
1SVX306AXX-XX31
-
These six VITA 65 slots plus one VITA 62 slot (6+1) backplanes are designed in alignment with The Open Group® Sensor Open Systems Architecture™ Technical Reference Standard, or SOSA®.
-
Product
PCI 18 Channel Precision Resistor Card
50-297-001
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
-
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 1.81kΩ
50-297-122
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Passive XMC-to-PCI Express Adapter
6066
-
Our Passive XMC-to-PCI Express Adapter +5VPWR 4X (6066) is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
PCI 8x9 RF Coaxial Matrix Card 75Ω SMB
50-725A-751
Matrix Switch Module
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
