PCI Backplanes
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
50-635A-006
Multiplexer Module
The 50-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express 16 Reed Relay Output
8004He
-
The 8004He PCI Express digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The isolated inputs protect the PC and other sensitive equipment from the voltage spikes and ground loop currents that are common to industrial environments. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications.
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779418-01
Multifunction I/O
16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device - The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
5U 6 slot ATCA backplane
109ATCA506-3013R
-
The 5U 6 slot ATCA backplane is a 6 slot replicated Mesh with radial IPMB, designed to meet 40Gbps (4 x 10G ports) data rates. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm
50-293-013
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Express Graphics Card With NVIDIA RTX 4500 Ada
NVIDIA RTX 4500 Ada
Graphics Card
- NVIDIA Ada Lovelace Architecture- Full height, full length design- PCIe Gen4x16 interface- 24GB GDDR6 Memory, 192-bit Bandwidth- 7680 CUDA Cores, 39.6 TFLOPS SP Peak
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-16-4C
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PCI Data Acquisition
-
PCI data acquisition product line provides 50MS/s, 500MS/s, 1GS/s and other high-speed digital conversion cards. These conversion cards feature 8- and 12-bit resolution, as well as wide bandwidth and large acquisition memory. The product line also includes PCI digitizers with on-board signal processing capabilities, and streaming firmware using the serial FPDP protocol to capture and transmit all acquired data without stalling or loss.
-
Product
8 Port PCI Express
PEX 8509
-
The ExpressLane™ PEX 8509 8-lane, 8-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device with an equal number of lanes and ports can be used in a wide variety of applications including control planes in the communications and networking markets, embedded systems, multi-function printers, network interface adapters, medical imaging systems, industrial-control systems and AMC cards.
-
Product
PCI Dual 20 X 4 Matrix 1 Pole Screened
50-511-021-S
Matrix Switch Module
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
2-port 10GbE PoE PCI Express Card
AX92324
-
Intel® Ethernet Controller X550-AT2, up to 10 Gbps data rate, Supports 15.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 25.5W per port, PCI Express x4 compliant, PoE power on/off via Power Manager software and API, Operating temperature range from 0°C to 55°C
-
Product
PCI Express 16 Isolated Input Digital Interface (10-30V)
8006He
-
Optimized for sensing up to 24V inputs, the 8006He PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
33 lane, 9 port, PCI Express
PEX 9733
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 395kΩ
50-298-042
Programmable Resistor Module
The 50-298-042 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 32 Channel Reed Relay Output Digital Interface
8007
-
The 8007’s PCI digital I/O interface reed relay outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
Product
ZIF PCI Test Connector
-
Meritec's ZIF PCI Test Connector offers the user an accurate and reliable way in which to test their PCI cards. With over 20,000 reliable cycles, it eliminates the need to constantly replace your PCI Connectors. Meritec's Test Connector assembly plugs directly into the PCI Connector in the test bed and is actuated by a lever for easy loading and unloading of cards. Meritec's solution eliminates the uncertainty associated with intermitancy between the PC Board and Test Connector during the test cycle.
-
Product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI 24 Channel TTL Digital Interface
8018S
-
The 8018S Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
PCI Reed Relay Card, 64xSPDT
50-110B-121
Reed Relay
The 50-110B-121 is a 64xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 32.7k Ohm
50-293-032
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Reverse Compact XMC-to-PCI Express (PCIe) Adapter
8260
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 8X (8260) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 5.82MΩ
50-297-052
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Dual Port Fibre Channel End-System Module for PCI Express
PCIe-FC4-NIC
-
Avionics Interface Technologies
Dual port module, operates as a Fibre Channel network node with support for multiple upper layer protocols.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
Programmable Resistor Module
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI I/O Products
-
Our PCI boards are based on technology and circuit designs with time-tested reliability in thousands of installations. Great effort goes into selecting high-performance parts to withstand the demands of military, aerospace, and manufacturing applications. Most models are available with extended temperature ranges for reliable operation in harsh environments. Acromag products are also designed for the long lifecycles required for OEM and defense projects.
-
Product
PCI Standard Programmable Resistor Cards
-
Pickering's PCI Standard Programmable Resistor Cards include fully programmable resistor and potentiometer cards for applications such as sensor emulation that require fine adjustment with a resolution down to 0.25 Ohm. All of our Programmable Resistor Cards can easily be formed to make Programmable Potentiometers by connecting two channels in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
Product
PCI Express 4 M.2 Receiver Test Automation
N5991PM4A
-
The N5991PM4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express M.2 devices and hosts at 8 GT/s.
-
Product
Multi-Channel (Up to Four) MIL-STF-1760 Interface Board for Conduction Cooled PCI Mezzanine Card Compatible Computers
EXC-1553ccPMC/Px(S)-1760
-
The EXC-1553ccPMC/Px(S)-1760 is a multi-channel (up to four) MIL-STD-1760 interface board for conduction cooled PCI Mezzanine Card compatible computers. In addition, Checksum, SRQ bit and Header Words are supported on each channel. Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.Each dual redundant 1760 channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. The EXC-1553ccPMC/Px(S)-1760 is supplied with C drivers, including source code, and Merlin+ Windows software.
