Automotive
Car industry or about cars.
See Also: Vehicle, V2X, Truck, Electric Vehicle, Car, Autonomous Vehicle, Autonomous Underwater Vehicle
-
product
SPC5 32-bit Automotive MCUs
The SPC5 family of 32-bit Automotive Microcontrollers is designed to accommodate a wide range of automotive applications ranging from Gateways, Electro Mobility, and ADAS to Engine and Transmission control, Body, Chassis and Safety. Based on a Power PC Architecture, SPC5 microcontrollers provide up to 3 cores operating at up to 200 MHz and with a 165 °C junction temperature.
-
product
PXI 8 Channel Switch Simulation Module
40-480-021
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, 750 V Isolation
43-752A-002
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Antenna Test Chamber for Automotive Radar
ATS1500C
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
product
Battery Impedance Tester
Is an ideal tester for automotive, UPS maintenance and telecommunication applications.
-
product
Dual-ridge Horn Antenna 1 to 18 GHz
EH118
EH118, a dual-ridge horn antenna that will operate from 1 to 18 GHz. This antenna has a balanced, smooth antenna factor curve that extends all the way to 18 GHz, a reduction of higher order modes on the aperture, and low return loss (SVSWR). The EH118 is applicable for commercial, military and automotive test standards and will include applicable calibrations. The EMC dual-ridge horn antenna offers these key features: single linear polarization, smooth/balanced gain with frequency, low return loss /VSWR, and ultrawide bandwidth (18:1).
-
product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-212
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Wire Harness/Automotive Probes
As a market leader, Feinmetall offers the largest product portfolio of application-specific contact probes and accessories for test module construction and wire harness testing. With innovative and economical solutions, we meet customer requirements and set trends in wire harness and automotive testing technology.
-
product
Compound Semi | MEMS | HDD Manufacturing
KLA has a comprehensive portfolio of inspection, metrology, and data analytics systems to support power devices, RF communications, LED, photonics, MEMS, CPV solar and display manufacturing. High brightness LEDs are becoming commonly used in solid-state lighting and automotive applications, and LED device makers are targeting aggressive cost and performance improvements, requiring more emphasis on improved process control and yield. Similarly, leading power device manufacturers are targeting faster development and ramp times, high product yields and lower device costs, and are implementing solutions for characterizing yield-limiting defects and processes. KLA's inspection, metrology and data analytics systems help these manufacturers control their processes and increase yield.
-
product
GNSS ICs
Teseo III, the latest generation of ST's GNSS ICs, offers reduced power consumption and carrier-phase tracking, allowing higher accuracy for automotive applications.
-
product
Acceleration Testing
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
-
product
PXI Dual Bus 32-Chan 2A Fault Insert Switch
40-190B-202
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781116-01
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
-
product
HDO4000A High Definition Oscilloscopes
HDO4000A Series
HDO4000A oscilloscopes have 4 analog input channels, 12-bit resolution using Teledyne LeCroy’s HD4096 high definition technology, up to 1 GHz of bandwidth and a compact form factor with a large 12.1” multi-touch display. They are ideal for debug and troubleshooting of power electronics designs, digital power management or power integrity analysis, automotive electronics systems, and deeply embedded or mechatronic designs.
-
product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
product
Radar Test System
UTP 5065
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
product
Interior Wiring Testing
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
product
Curve Tracer
CS-10000 Series
Hi-voltage devicesDevelopment of new devices (SiC/GaN)Automotive Companies
-
product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
product
Digital Auto Multi-Meter
This Digital Auto Multi-Meter (DAMM) was designed solely for Automotive Technicians for troubleshooting all electrical problems encountered in the vehicle. Be it a 6V, 12V or 24V system it can be used to check Amps draw directly on the fuse (Mini, ATC or Maxi Fuses) without having to remove it and measure parasitic drain current using the parallel method at the fuse box.
-
product
PCI-4462, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 4-Input Sound and Vibration Device
779309-01
The PCI‑4462 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous four-channel dynamic signal acquisition with six programmable gain settings for making high-accuracy, frequency-domain measurements. The PCI‑4462 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications for dynamic signal acquisition devices include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
product
Ambient Light Sensors
Renesas' ambient light sensors optimize display backlighting, enhance energy efficiency, and improve user experience with ultra-low light sensitivity, low power consumption, and precise spectral response. Our offerings include light-to-digital sensors with IR blocking filters and I2C interfaces, and light-to-analog solutions integrating photodiodes and amplifiers. Designed for automotive, industrial, and medical applications, these sensors deliver reliable performance even in demanding environments.
-
product
Precision Multi-Channel DC Source PXI Card
GX1838 Series
The GX1838 is a multi-channel programmable DC Source providing multiple discrete outputs for avionics automotive, industrial testing and other ATE applications.
-
product
PXI Voltage Amplifier SMB Type Connector
41-650-002
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
Test Stand Controller for Automotive, Marine, and Aerospace Engine Testing
SPARC
The new SPARC Engine is the state-of-the-art test stand controller for automotive, marine and aerospace engine testing. The latest generation offers you advanced hardware and software for the highest performance, and touch functionality for intuitive operation. It is suitable for test stands with a synchronous machine (DYNASPM), asynchronous machine (DYNAS3), hydraulic dynamometer (DT) and eddy current dynamometer (WT) as well as tandem applications.
-
product
Power Management and System Basis ICs
ST provides a large selection of Power Management ICs and System Basis Chips (SBC) specifically designed for automotive electronic systems.
-
product
Hand Multipliers
Perfect for service applications, Mountz hand torque multipliers bring power to where your workers need it most. Since they don’t rely on electric, pneumatic, or hydraulic power, hand torque multipliers are great tools for heavy fieldwork. Their small size, light weight, and durable construction make them convenient for field techs to carry, and their strength—up to 36,880 lbf.ft of precisely controlled torque—ensures that your workers can tackle any job. Useful in automotive, heavy machinery, petrochemical, power generation, mining, boring, and shipping, Mountz hand torque multipliers provide maximum capability with minimal investment.
-
product
Komodo CAN Duo Interface
TP360110
The Komodo™ CAN Duo Interface is a powerful two-channel USB-to-CAN adapter and analyzer. The Komodo interface is an all-in-one tool capable of active CAN data transmission as well as non-intrusive CAN bus monitoring. The portable and durable Komodo interface easily integrates into end-user systems. It provides a flexible and scalable solution for a variety of applications including automotive, military, industrial, medical, and more.
-
product
Test And Measurement
Test and Measurement supplies test, measurement, and analysis equipment and software for product design optimisation, manufacturing control, and environmental monitoring systems. Markets are principally the aerospace, automotive, consumer electronics and oil and gas industries. For customers in the automotive and aerospace industries, our products and applications help them to design and test new products whilst reducing time to market. In consumer electronics, our equipment and software enable customers to refine the performance and accuracy of their products and to test them in the production process. In the environmental monitoring market, the desire for higher standards of community comfort is creating additional demand. In the oil and gas industries, our products and solutions optimise the recovery rates of oil and gas reservoirs and support the development of cost-efficient extraction processes in a safe manner that minimises the impact on the local environment. The operating companies in this segment are Brüel & Kjær Sound & Vibration, ESG Solutions, HBM and Millbrook.
