Current Detectors
-
-
Product
Voltage Detectors & Testers
-
Non-contact AC voltage detector quickly checks for the presence of live voltage on wiring and electrical devices. Features a built-in flashlight for added convenience.
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
Product
Burden Set – Current
BSC-102
-
The industry has recognized the actual load (burden) on CTs is lower than the standard ANSI burdens allow. So a new IEEE Specification (IEEE C57.13.6) accommodates that fact by introducing two new burdens and two new accuracy classes. This new specification address “High Accuracy”CTs.
-
Product
Slipping Torque Detector
DI-12 series (SL4/SL02/SL15)
-
Torque measurement of tightened screws. Measure how much force the tightened screw is tightened. By capturing the occurrence of slippage with high accuracy and measuring the torque, it is now possible to measure the torque value of a tightened screw. For sampling inspection of products and setting and management of output torque of power drivers.
-
Product
Broadband Detectors
-
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
Product
Cable Continuity Detectors
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Cable Continuity Detector can test the open circuit, short circuit, crossover and continutiy for RJ11/RJ45/BNC/USB cable, and the test result is displayed by the visible LED light status.
-
Product
Ultrasonic Flaw Detectors
-
Our full range of portable ultrasonic flaw detectors (UT) provides unmatched capabilities for locating discontinuities and other flaws. A wide range of software options is available for enhanced flaw detector inspection.
-
Product
Gas Detectors
-
CO2, Humidity And Temperature Sensors, Dual Wavelength NDIR CO2 Sensor (Non-Dispersive Infrared) For Superior Stability, User Operated CO2 Calibration, Data Hold & Max/Min/STEL/TWA Function
-
Product
Non-Contact H.V. Detector
375 HP
-
Standard Electric Works Co., Ltd
● Protection class : IP65.● 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV● Bright LED visual indication● Frequency range: 40~70Hz● Flashlight funcion●Wider angle for voltage detection(120°)●Audible indication● Easy-to-prove method● Self-test function● Power source : 1.5V "C" type battery × 3● High impact nylon casing● Non-contact work by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Suitable for indoor and outdoor use● Easy access to batteries.● Special ranges are available upon request. ● The maximum detection range can be 500kV.● Meets EN 61326-1 CISPR 11 EN 61000-4-2 EN 61000-4-3 EN 61000-4-8
-
Product
Remote Spectral Detector
CSS-45
-
The CSS-45 detector incorporates a powerful microprocessor which performs not only data acquisition but also all necessary lighting calculations. Both USB 2.0 and RS 485 interfaces are standard enabling the flexible configuration of single and multi-detector based systems. An optional software development kit supports integration into third party application software. With its wide spectral range from 360 nm to 830 nm the CSS-45 is ideal, for example, as a high accuracy photometric and colorimetric detector (according to CIE S023).
-
Product
Portable Gas Detector
PPM Gasurveyor 500
-
Teledyne Gas & Flame Detection
The PPM Gasurveyor 500 compliments the Gascoseeker 2-500 with a similar performance, measuring % LEL and % volume flammable hydrocarbons, but with the addition of ppm ranges for all aspects of leak detection. The high sensitivity parts per million (ppm) range is enhanced by the ppm search range with higher sensitivity and faster response.
-
Product
Non Contact Detectors
-
*Adjustable to safely detect power and low voltage*Safely detects AC voltage without touching the bare conductor*Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits*Use to detect voltage in outlets, lighting fixtures, wires and cables*Finds breaks in wires*Identifies hot and neutral conductors*Low battery indication
-
Product
AC Current Transducer
iDVM 333
-
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
Product
Detector & Controller
LM-Pbs TEC1
-
Lead-Sulfide Detector (Range: 1 - 2.4 micron) Detector element is 5mm x 5mm. Has a 2 stage Thermoelectric Cooler which increases the gain by 3x without an increase in noise. This is a recommended upgrade when using a monochromater with a LMC-20.
-
Product
ElectroMagnetic Detector
MP Series
-
MP-900/9000 are chiefly used in conjunction with a detector gear mounted onto a rotating shaft by bringing the detector into proximity to the gear so that the detector outputs frequency signal of which is proportional to the rotational speed. So various types are available including low-priced, general purpose, oil proof and heat resistant types that you can make a choice for your usage.Signal cables (except attached-cable types), extension cables and connectors are sold separately.
-
Product
Detector Testing
-
CI Systems' Optical Test benches are especially built to test many types of detector arrays used as the sensors of a camera, from visible to far infrared ranges. With CI Systems' expert know-how, these test benches can be tailored to a customer's design requirements. MTF, spectral response, crosstalk, NETD and sensitivity are some of the basic parameters that can be tested with CI's Optical Test benches during the design, manufacturing and integration of detector arrays.
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Detectors - RF / Microwave
-
PMI offers a full line of RF and Microwave detector products that range from 2 MHz up to 40.0 GHz. Many options are available. If you do not see exactly what you require on this web site please contact
-
Product
Integrated Current Sensors
-
Current sensors have to be smaller, smarter, cheaper. LEM’s R&D is actively developing a range of ICS to reduce the footprint of the current sensing function and simplify the integration of current measurement in a wide range of applications in automotive, industrial, or residential.
-
Product
Ignition Pulse Detector
IP-3100
-
The IP-3100 enables ignition pulse detection of gasoline engines with high sensitivity. The rotation speed can be easily measured by clamping the primary side cord (low voltage), the secondary side cord (high voltage), and current cable of the electronic distributor. The IP-3100 is used with the tachometer made by Ono Sokki.
-
Product
Current Sensors
-
Achieve higher efficiency and power density with our industry-leading current sensor ICs. Perfect for vehicle electrification as well as green industrial, computer and consumer applications.
-
Product
Current Amplifiers
-
In order to achieve an extremely low noise performance very high gains were chosen, while nevertheless minimizing the associated bandwidth reduction.Thus, as a result of our sophisticated development efforts we can offer a professional "High-End" Current Amplifier line. The noise performance of our products surpasses by far that of conventionally designed OpAmp current-to-voltage converters at the corresponding bandwidth.
-
Product
Thermal Traffic Detector
TrafiSense
-
TrafiSense is an integrated thermal sensor and detector for vehicle and bike detection. TrafiSense does not need light to operate, but uses the thermal energy emitted from vehicles and bicyclists. This enables the sensor to detect vehicles and bikes in the darkest of nights, over a long range and in the most difficult weather conditions. The result is reliable, 24/7 traffic detection for a wide range of applications.
-
Product
Specialty Coating Detectors
-
This NEW dual-purpose detector combines two instruments into one. Use the same device to identify the coated surface of glass for either the ShowerGuard or DiamondGuard coatings available from Guardian Industries.
-
Product
SF6 Leak Detector
-
The Amperis SF6 leak detector uses an innovative infrared absorption detection cell that is extremely sensitive to SF6.
-
Product
RFI Detector Meter
MFJ-805
-
Use this ultra-sensitive pocket-sized RFI Detector to track down and eliminates RFI caused by radiating cables and wires. Usable from VLF to VHF. Gain adjustable over 50dB range.
-
Product
Scanning X-Ray Detectors
Shad-o-Scan
-
Shad-o-Scan is a family of scanning X-ray detectors specifically designed for the challenging requirements of high-performance industrial and scientific X-ray applications. Industry-leading TDI CCD performance enables the ultimate sensitivity and highest resolution in the industry, and ensures long detector lifetime in even the harshest radiation environments.
-
Product
Wheel Play Detectors
-
A play detector consists of two plate units on which the wheels of an axle are placed. The plates are moved horizontally in an oscillating fashion by hydraulic cylinders. This movement can be done in different directions. In this way an inspector in the inspection pit can easily check for play on the different components underneath the vehicle. To make it even easier, the remote control unit to start and stop the plate movement has a built-in lamp.
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
