PCI Express
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller. Also known as: PCIe
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, Serial ATA, Serial Peripheral Interface, SMBus, PCI Express Test, PCI Express Analyzers, PCIe
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
RGB Video Driver
PCI900
-
The PCI900 is a PCIe form factor module that has dual RGB analog video receiver inputs. It outputs two analog RGBs that provide the capability to drive UXGA video up to 110 feet over coaxial cable. The input impedance is 75 ohms with a signal level of 1 VPPper RS-343A with sync on green. The output characteristic being 1 VPP into 75 ohms per RS-343A which can drive a minimum of 110 feet of cable.The PCI900 receives only power from the PCIe bus and has no other connection to the PCIe bus.
-
Product
COM Express™ Type 2 Development Baseboard
CEB94000
-
The COM Express development baseboard, the CEB94000, supports standard ATX form factor, flexible expansion with PCIe x16, PCIe x1 and 32-bit/33MHz PCI bus. Dual 7 segments port 80 display is reserved for convenient debugging purpose.
-
Product
8 Ports 1GbE RJ-45 Network Management Card
NMC-0807
-
Ideal for multi-segment network deployments. 2 x Intel® i350-AM4, 8 Ports RJ45 connector, 1x PCIe x4, Gen2.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PCI Express Image Acquisition Frame Grabber
Xcelera-HS PX8
-
The Xcelera-HS PX8 has been built within Teledyne DALSA’s Trigger-to-Image Reliability technology framework. Trigger-to-Image Reliability leverages Teledyne DALSA’s hardware and software innovations to control, monitor and correct the image acquisition process from the time that an external trigger event occurs to the moment the data is sent to the host, providing traceability when errors do occur and permitting recovery from those errors.
-
Product
4K HEVC Broadcast Video Encoding Card
VEGA-3311
-
a high-performance, hardware-based PCI Express or openGear module designed for real-time compression of 4K UHD video (up to 60fps) using the H.265 standard.
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
6U VPX Computing Payload
VP62108
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62108 is a 6U VPX computing payload based on Intel® 4th generation Core™ Processor. It supports Intel® 4th generation Haswell architecture i3/i5/i7 dual-core or quad-core embedded processor, up to quad-core i7 processor 4860EQ with a life cycle of more than 7 years.VP62108 provides four serial RapidIO (SRIO) x4 links for VPX data plane communications, two x8 PCIe links for VPX expansion plane communications and four Gigabit Ethernet links for VPX control plane communications. Its rich data exchange capability allows users to easily build the whole machine or system-level solutions.VP62108 supports up to DDR3L 16GB ECC memory and offers reliable data transmission. Its onboard solid state Flash managed by a SATA interface controller can be up to 64GB SLC or 128GB MLC. And the entire board uses the reinforced conduction-cooled design and has a wide operating temperature, allowing the user not to worry about its working stability in harsh environments. This feature makes VP62108 particularly suitable for critical mission areas.
-
Product
Power Supplies
CUL-950B
-
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
COM Express Rev. 3.1 Basic Size Type 7 Module with AMD Embedded Ryzen™ V3000
Express-VR7
Computer on Module
ADLINK’s Express-VR7 COM Express Type 7 Basic size module is based on AMD Embedded Ryzen™ V3000 series processor. Offering up to 8 cores and 16 threads at 15W/45W TDP, the module exhibits the best performance per watt in its class, along with 14x PCIe Gen4 lanes with enterprise level reliability and extreme rugged temperature option (-40°C to 85°C).
-
Product
PCIe to cPCI Bridge
Strain/Bridge Input Module
3U/ 4HP CompactPCI remote controller for use in CompactPCI rear system slot inside a 19″ chassis, PC PCIe interface card for standard desktop PC, allows control of CompactPCI Chassis from desktop PC
-
Product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
-
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
2 Ports 25GbE SFP28 Network Mezzanine Card
NMC-2501
-
1 x Intel® XXV710DA2, 2 x SFP28 slots, 1 x PCIe x8, Gen3, RoHS compliant.
-
Product
Digital I/O Card w/CoS IRQ
PCIe-DIO-24HS
-
This product is a x1 lane PCI Express digital I/O board available in two models. The PCIe-DIO-24H is the basic DIO and the PCI-DIO-24HS features advanced change-of-state (COS) detection capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
PCIe-6535B, 32-Channel, 10 MHz, 40 MB/s Digital I/O Device
782629-01
Digital I/O Module
The PCIe-6535 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
Power Cable For GPU Card - Two 4-Pin 12V
1700029268-01
PCIe Cable
Output：6+2-pin PCIe power conn.Input：2* CPU 4-pin conn.Lenth：10 cm (3.94")Compatible Devices：PSU
-
Product
PCI Express Gen 1 Test Backplane
SKU-015-01
-
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
Product
PXIe 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels
M4X.4451-X4
Digitizer
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
COM Express Compact Size Type 6 Module with Intel Pentium, Celeron N3000 Series and Atom x5 E8000 SoC (formerly codename: Braswell)
cExpress-BW
Computer on Module
ADLINK cExpress-BW provides two DDI channels (with up to 4K resolution) and one eDP or DDI3 channel supporting three independent displays, enabling it to drive multiple HD screens without the need for a discrete graphics card. In addition, LVDS is optionally available to support next generation displays. The cExpress-BW offers up to five PCI Express lanes x1. A wide range of operating systems are supported, including Linux, Windows 7 and 8.1u, Windows Embedded Standard 7, Windows Embedded Industry 8.1 and VxWorks.
-
Product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 4 Channels
M4I.4451-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
FPGA Card
PC820
-
The PC820 is a high-performance, PCI Express card with advanced DSP capabilities and multiple I/O options. It supports one FMC+ VITA 57.4-compliant HPC FPGA Mezzanine Card (FMC) that is closely coupled to the Virtex or Kintex UltraScale FPGA and a DDR4-2133 SDRAM SO-DIMM. The PC820s PCIe Gen3 interface can support up to eight lanes.
-
Product
Micro ATX Motherboard With LGA1151 Socket 7th/6th Gen Intel® Core™ Processor, Intel® Q170, USB 3.0, SATA 3.0, Dual LAN, VGA, DisplayPort, DVI-D, And HDMI
MMB501
-
The MMB501 is powered by the LGA1151 socket 7th/6th generation Intel® Core™ i7/i5/i3, Pentium® and Celeron® processors (formally codename: Kaby Lake/Skylake) with Intel® Q170 chipset. The MMB501 supports four high bandwidth 288-pin DDR4-2133/2400 with a memory capacity up to 64GB. The industrial-grade micro ATX motherboard is expandable with one PCIe x16 slot, two PCIe x4 slots, one PCI slot and one full-size PCI Express Mini Card slot. Moreover, the embedded board supports triple-display via DisplayPort, HDMI, DVI-D and VGA interfaces. Furthermore, this outstanding multi-function embedded motherboard is integrated with the Intel® HD Graphics 530/510 to deliver stunning UHD 4K resolution and fast 3-D and video playback for graphics-intensive applications. To meet the distinct needs from users, there are six SATA-600 with RAID 0/1/5/10, six USB 3.0, five USB 2.0, four RS-232 ports, two RS-232/422/485 ports, one DisplayPort, one DVI-D, one HDMI and one VGA, as well as has two Gigabit Ethernet ports with Intel® i219LM and Intel® i211AT controllers. To ensure stable and reliable operation, the high-performance Intel® Core™-based industrial micro ATX motherboard supports a watchdog timer and hardware monitoring features. Furthermore, this new embedded board runs well with Windows® 7, and Windows® 10 operating systems.
-
Product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
Digital I/O Module
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
Adaptive Relay, Virtex-6 FPGA - 3U VPX
Model 52624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
ASMB 2U PCIe Gen.3 X16 To X8x8 Card (RoHS) For Dual-Card PCIe Configurations.
ASMB-RF388-21A2E
-
Support 2U HPC server chassis seriesSupport 2 PCIe Gen.3 x8 slots or 1 PCIe Gen.3 x8 + 2 PCIe Gen.3 x4 slotsSupport ATX/Micro ATX/EATX ASMB motherboard series
-
Product
Industrial Motherboards & Slot SBC
-
Industrial ATX Motherboard is a standard form factor allowing customers to seamlessly upgrade without compatibility issues. Our ATX MB and embedded MB has longevity support and also provide flexible PCIe and PCI card expansion, reach high performance and offer a wide range of computing capacities.
-
Product
Embedded Boards
-
Elma offers embedded computing board level products, including single board computers, mass storage, Ethernet and PCIe switches, FPGAs and custom I/O solutions. Our focus is to provide proven technology based on standard architectures like VME, VPX, CPCI, ATCA, and COM-Express as well as other standard and custom small form factors. We partner with leading board manufacturers.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB109
-
The FAB109 features a PICMG 1.3 CPU card slot, one PCIe x16 slot and three PCIe x1 slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB109 is compatible with Axiomtek's AX60501 and AX6052 chassis.
