PCI Express
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller. Also known as: PCIe
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, Serial ATA, Serial Peripheral Interface, SMBus, PCI Express Test, PCI Express Analyzers, PCIe
-
Product
Low Profile PCI Express 1-Port
7106e
-
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
2-port/4-port PCI Express 1GigE PoE Card with M12 X-
AX92325
-
Four M12 x-coded connectors with special design (to avoid occupying two slots) 2 or 4 independent Gigabit PoE ports, Supports 9.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 30W at 54 VDC per port, PCI Express x4 compliant
-
Product
PCI Express Card
EXC-4000PCIe/xx
-
The EXC-4000PCIe/xx card for the PCI Express bus supports up to four dual redundant 1553 channels using the M4K1553Px(S) module and is compatible with all common variations of MIL-STD-1553 (A, B).
-
Product
XMC-to-PCI Express (PCIe) Adapter
8366
-
The Technobox, Inc. P/N 8366 Compact XMC-to-PCIe (PCIe) adapter permits use of a standard VITA 42.3 air-cooled XMC in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version. It provides up to eight lanes (8X) from the XMC's P15 connector to the edge fingers.
-
Product
4-Port PCI Express
PEX 8617
-
The ExpressLane™ PEX 8617 device offers 16 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 4 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 16-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for two M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-32e
-
This Squid PCIe Carrier board can support up to two M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2230, 2242, 2260,2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
Arowana PCI Express SSD Board™ Family x4 PCI Express Gen 3 SSD board
SKU-090-31-x4
-
The Arowana PCI Express SSD board is the smallest carrier board on the market. This PCI Express Carrier board was designed to expand modern motherboards or embedded systems that have a PCI Express interface. It can also be vertically installed in any 1U servers or appliances.
-
Product
5 port, PCI Express
PEX 9716
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8065
-
The Technobox, Inc. P/N 8065 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
PCI Express Validation License Suite
SW00PCIE
-
The PCI Express Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for PCI Express with coverage across the PCI Express technology starting from Gen4. Together with the subscription model, this enables the support and coverage continuity as the PCI Express technology progresses through generations.
-
Product
PCI Express FMC Carrier
RFM-BSC5GT7H1
-
Sundance Multiprocessor Technology Ltd.
The RFM-BSC5GT7H1 is a PCI Express short sized FMC carrier board with Cyclon V FPGA (Altera), which is designed mostly for low cost, high-performance data acquisition.
-
Product
Compact XMC-to-PCI Express (PCIe) Adapter
9296
-
Our Compact XMC-to-PCI Express (PCIe) Adapter 8X (Front-Panel I/O Only) (9296) permits use of a VITA 61 (XMC 2.0) device in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version.
-
Product
PCI Express (PCIe) 5.0 and Compute Express Link (CXL) Protocol Analyzer
Summit T516
Protocol Analyzer
The Summit T516 is targeted at high-speed PCI Express 5.0 and CXL I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
Product
PCI Express® 5.0 Interposer
OCP NIC 3.0
Interposer
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
Product
x1 PCI Express Extender
SKU-006-01
-
The x1 PCI Express Extender was designed to support the development, debugging and verification of PCI Express boards. The Extender provides a complete PCI Express debugging platform that allows easy access to the logic signals, it has overcurrent protection and hot-swap operation capability.
-
Product
ATX Motherboard With LGA1151 Socket 8th Gen Intel® Core™, Xeon® E Processor, Intel® C246, USB 3.1 Gen2, SATA 3.0, PCI Express Mini Card Slot, VGA, DisplayPort, DVI-D, And HDMI
IMB525
-
*LGA1151 socket 8th gen Intel® Core™ i7/i5/i3, Xeon® E, *Pentium® or Celeron® processor (Coffee Lake)*Four 288-pin DDR4-2666/2400 ECC DIMM for up to 64GB of memory*DisplayPort, DVI-D, HDMI and VGA with triple-view supported*6 SATA-600 with RAID 0/1/5/10*1 PCI Express Mini Card slot (optional)*2 USB 3.1 Gen2 and four USB 3.1 Gen1*TPM 2.0 supported (optional)
-
Product
PCI Express Receiver Board
AD12-2000-IRIGB
-
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
Product
PCI Express card carrier, PCIe Gen 3 x8 connection
SA4-COUNTRY
-
The SA4-COUNTRY is a peripheral slot board for PICMG® CompactPCI® Serial systems and acts as carrier for low profile PCI Express® Card. The SA4-COUNTRY is provided with a PCI Express® x8 connector.
-
Product
Fanless Embedded System With LGA1151 Socket 7th/6th Gen Intel® Core™ & Celeron® Processor, Intel® H110, HDMI, DisplayPort, VGA, 6 USB, 4 COM, PCI Express Mini Card Slot And 10 To 30 VDC
eBOX640-500-FL
-
The eBOX640-500-FL is powered by the 7th generation Intel® Core™ i7/i5/i3 and Celeron® processor families. It features dual DDR4-2133 DIMM sockets with up to 32GB of system memory, and provides a wide choice of front-accessible I/O interfaces for easy cabling and maintenance. It supports an extended operating temperature ranging from -10°C to +55°C, a wide voltage range DC power input from 10 to 30 VDC with power protection, and up to 2G vibration endurance, enabling a reliable and stable operation in harsh environment. The superior Intel® Kaby Lake-based fanless embedded box PC can support three independent high resolution displays and 4K resolution, offering high quality imaging.
-
Product
97 lane, 25 port, PCI Express
PEX 9797
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
Reverse Compact XMC-to-PCI Express (PCIe) Adapter
8260
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 8X (8260) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8464
-
The Technobox, Inc P/N 8464 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths.
-
Product
PCI Express Card
EXC-8000PCIe/xx
-
The EXC-8000PCIe/xx card for the PCI Express bus supports up to forty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.
-
Product
PCI Express Board Retainer
SKU-038-0X
-
The PCI Express Board Retainer prevents the host card from wiggling, and allows a PCI Express board to be held in place without a bracket.
-
Product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
-
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
Arowana PCI Express SSD Board™ Family 2U x16 (x8) PCI Express Gen 3 SSD board
-
The Arowana PCI Express SSD board incorporate up to eight independent x4 PCI express Gen 3 SSDs. The operating system recognizes each SSD as an individual hard disk and can combine them in RAID0 to gain maximum performance.
-
Product
Low Profile PCI Express 2-Port
7202ec
-
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
PCI Express CONET2 Controller
A3818
-
The Mod. A3818(*) is a PCI Express x8 card that can plug into both x8 and x16 PC PCI Express slot (V2.0), which allows the control of up to 4 CONET2 independent networks (each network can be made of up to 8 CONET2 slaves).
-
Product
104-lane, 52-port, PCI Express
PEX89104
-
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
-
Product
Flexible x4 PCI Express to 4 MiniPCI Express Splitter
SKU-072-0X
-
Flexible x4 PCI Express to 4 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows connecting up-to four MiniPCI Express add-in expansion boards to the standard motherboard PCI Express connector.Splitter includes 4 MiniPCI Express Adapter boards, x4 PCI Express Host board and 4 Flat PCI Express Cables.
