Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
Data Acquisition 32 ch. Module
CPCI-AD16/16-6U
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
Product
PCI/cPCI-VME link/interface
SIS1100/3100
-
The SIS1100/SIS3100 PCI/cPCI to VME interface card combination was developed to meet the requirements of demanding VME data acquisition systems. The link is optimized for low latency high speed readout.
-
Product
Analog Output Expansion Board
MSXB 032
-
The MSXB 032 Analog Output Expansion Board converts digital inputs from a Data Acquisition Processor into four separate analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a Data Acquisition Processor for a maximum expansion of 64 analog output channels. The MSXB 032 is compatible with Microstar Laboratories Industrial Enclosures.
-
Product
Modbus Analog Output Modules
DAT3020 Series
-
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
Product
Test Automation System for Brake Testing
STARS Brake
-
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
-
Product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 2-Pole
40-610A-006
Multiplexer Module
The 40-610A-006 is a 4-bank, 16-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
DAQ Systems
-
Data acquisition systems (DAQ or DAS) collect information from connected sensors and other instrumentation to measure and record electrical and physical quantities, such as voltage, current, temperature, strain, pressure, shock, vibration, distance, displacement, RPM, Angle, and weight. A DAQ System typically consists of sensors, measurement hardware with signal conditioning and an Analog-to-Digital converter, and a computer with programmable software for data logging and analysis.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 180 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.827-04
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXI Ultra High Density 64x2 2-Pole Matrix
40-533B-032
Matrix Switch Module
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
Spectroscopic Ellipsometer Software
SpectraRay/4
-
SpectraRay/4, the SENTECH proprietary spectroscopic ellipsometry software, includes data acquisition, modeling, fitting, and extended reporting of ellipsometric, reflection, and transmission data. It supports variable angle, multi-experiment, and combined photometric measurements. SpectraRay/4 includes a huge library of materials data based on SENTECH thickness measurements and literature data as well. The large number of dispersion models allows modeling of nearly any type of material.
-
Product
CB-37F-HVD, 37-pin ScrewTerminal Blk, UL rec.150V CAT II, Din Rail
779491-01
-
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, High Voltage Horizontal DIN Rail Terminal Block - The CB-37F-HVD features screw terminal connectivity for up to 37 I/O signals, 12 to 30 AWG. It has a female 37-pin D-SUB connector for connectivity to C Series I/O Modules and … data acquisition devices. The CB-37F-VHD is UL recognized. You can use the CB-37F-VHD with low-voltage or high-voltage products up to 150 V.
-
Product
IC & Transformer
-
Mornsun Guangzhou Science & Technology
MORNSUN launched the self-designed electronic integrated circuits according to the different product lines, types of the integrated circuit include AC/DC power supply control ICs, DC/DC power supply control ICs, interface ICs, start-up ICs, contactor power saving controller ICs and digital isolator ICs. MORNSUN IC chip can be widely used in industrial equipment, process control, data acquisition system, building automation, smart meter, etc. Adopting MORNSUN's AC/DC transformers and DC/DC transformers, with the use of its control ICs, can achieve wide voltage input flyback power supply design with multiple protection functions and superior EMI performance. We hope that those power transformers along with the integrated circuits & chips electronics can be an ideal fit for your application needs.
-
Product
COM Express Compact Size Type 6 Module with Up to Quadcore Intel® Core™ and Celeron® Processors
cExpress-WL
Computer on Module
ADLINK introduces its latest COM Express Type 6 modules to fulfill the needs of size, weight, and power (SWaP)-constrained edge computing applications. ADLINK’s cExpress-WL modules feature the 8th generation Intel® Core™ and Celeron® processors (formerly codenamed Whiskey Lake-U) with up to 4 cores and up to 64GB memory capacity, offering edge computing applications uncompromising performance and responsiveness despite SWaP constraints. The cExpress-WL is suited for applications such as data acquisition and analysis, image processing, and 4K video transcoding and streaming at the edge.
-
Product
PXI Single 44x4 Matrix, 2 Pole Switching
40-523-022
Matrix Switch Module
Medium density PXI dual 44x4, 2-pole matrix - it is also available in reed relay formats of 1-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PXI 2A Multiplexer, 16-Bank, 8-Channel 1-Pole
40-614-001
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
PXI 12x8 Matrix, 2 Pole Switching
40-512-022
Matrix Switch Module
The 40-510 series of matrix modules feature a wide range of selectable switchingconfigurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signalrouting in ATE and data acquisition systems.Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Larger matrices may be constructedby Daisy Chaining the common signals from multiple PXI modules.
-
Product
Dual Channel Digital Receiver
MS 1740
-
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
Product
High Voltage System
HV-2
-
International Electro-Magnetics, Inc.
*Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.
-
Product
USB DAQ
-
ADLINK USB DAQ modules leverage the expertise of ADLINK's analog design capability, enhancing convenience of data acquisition. Simply plug the ADLINK USB DAQ into a USB port on your computer or notebook for performance equaling or even exceeding that of ADLINK PCI/PCIe DAQ cards, with no need to power down or open the chassis. As well as providing basic voltage measurement, ADLINK USB DAQ modules feature built-in signal conditioning to directly receive measurement from most commonly used sensors, with no need for extra signal processing. From basic testing to high-accuracy measurement, from portable application to industrial automation, the ADLINK USB DAQ series delivers easy, efficient, and accurate measurement every time.
-
Product
20 Channel Multiplexer (2/4-wire) Module for 34970A/34972A
34901A
Multiplexer Module
The Keysight 34901A module for the 34970A/34972A Data Acquisition/Switch Unit is the most versatile multiplexer for general purpose scanning. It combines dense, multi-function switching with 60 channel/second scan rates to address a broad spectrum of data acquisition applications.
-
Product
PXI Dual 16x8 Matrix, 2 Pole Switching
40-532-022
Matrix Switch Module
This high-density reed relay matrix with 256 crosspoints. This model is configured as a Dual 16x8, model 40-531 is configured as a 32x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version can be used for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
Product
PXI 2 Amp Multiplexer, Dual 8-Channel, 4-Pole
40-635A-007
Multiplexer Module
The 40-635A-007 is a dual 8-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790662-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
High Speed Ethernet DAQ
-
Ultraview's ethernet based acquisition boards bring low noise, large channel count solutions to common open-source platforms. The flexibility of being able to combine a large number of publicly available firmware/software modules with laboratory quality data acquisition chips makes many previously difficult project integrations possible at a fraction of the cost of developing the entire system.
-
Product
PXI Very High Density MUX 24 Chan 8 Pole
40-675-002-24/8
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
Data Acquisition Systems
-
Encore Electronics manufactures a wide range of analog signal conditioning equipment, including strain gage and pressure amplifiers, frequency-to-voltage converters, thermocouple isolation amplifiers and anti-aliasing filters.
-
Product
Portable Signal Conditioning System
SCS-800
-
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
-
Product
PXI MUX 4 Bank, 16 Channel Screened 1 Pole
40-610-021-S-4/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Data Acquisition and General Purpose Test Equipment
-
All Fluke data acquisition products feature unique, built-in universal signal conditioning and a plug-in Universal Input Module to enable you to measure virtually any type of signal without having to purchase extra equipment. Plus, powerful, easy-to-use Windows®-based software supports easy configuration, advanced trend analysis, professional- quality reporting, and enables you to quickly build human-machine-interfaces without any programming.
