Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
Product
Power Sources
GF303
-
Beijing GFUVE Electronics Co.,Ltd.
GF303 Program-controlled three phase AC standard power source is a high precision three phase AC standard current source and AC standard voltage source.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-03
-
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
8FE + 2FE/GE SFP Port Managed Industrial Ethernet Switch
EKI-5710E-2FI
-
Redundancy: X-Ring Pro (ultra-high-speed recovery time, <20 ms), RSTP/STP (802.1w/1D), IXM function for fast deployment, Security Pack with 802.1X, ACL, RADIUS, TACACS+, MAB Authentication, SNMPv3, HTTPS, SSH, and SFTP. Management: SNMP v1/v2c/v3, WEB, Telnet, standard MIB, private MIB, Supports NMS for easy and visualized to monitor and manage network remotely.
-
Product
60-Watt DC/DC Converter, 3U cPCI
55KQ2-02
-
NAI’s 55KQ2-02 is a 60 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 60 Watts. It is designed to work along with NAI’s 72.5 DC Power Line Conditioner w/Holdup companion unit, model 44KS3-02.
-
Product
Diode Power Sensor
8487D
-
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
Product
Plate Load Test Apparatus
-
These test machine isused to estimate the bearing capacity of a soil under field loading conditions for a specific loading plate and depth of embedment (ASTM) , and also for load tests of soil and flexible pavement components in evaluation and design of airport and highway pavements . We propose a complete range of plate load testing equipment conforming to the different standards.
-
Product
8 Channel ADC for CompactPCI
CPCI393
-
The CPCI393 8-Channel Differential Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
Wall Mount Kit For All PPC Models
PPC-174T-WL-MTE
-
Includes VESA standards:75 x 75 mm and 100 x 100 mm hole pattern bracketPanel adjustable: 360°Panel up & down adjustable: 46°Panel left & right swivel : 46°Max. Load-bearing: 15 Kg
-
Product
A PoE-PD I/O Board
AX93274
-
*PoE-PD I/O board complies with IEEE802.3at standard via an internal cable to power on SBC*100 x 32 mm*1 x LAN cable, 1 x power cable, 1 x thermal module*Compliant products: PICO831, PICO121, PICO841, PICO843
-
Product
SparkFun I2S Audio Breakout
MAX98357A
-
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
-
Product
Precision Multirange Current Transformer
P-5000
-
The P-5000 transformer is a laboratory standard. The unit’s excellent accuracy and the Knopp One-to-One calibrating feature make this precision transformer well-suited as a standard for calibration work. This transformer can provide a very accurate determination of the ratio and phase angle characteristics of current instrument transformers having ratios from 5 to 5,000 amperes. This transformer also can accurately extend the range of a 5 ampere ammeter or wattmeter to cover all current values up to 5,000 amperes.
-
Product
Tilt Switch and Control Unit
MTS / SCU-200
-
Features• Detects the presence or absence of bulk material• Standard enclosure is NEMA 12 with indicator lights• NEMA 4 and Intrinsically Safe enclosures available• Rugged heliarc-welded steel probes• Use with SCU-200 for complete monitoring system
-
Product
FPGA Mezzanine Card
FMC432
-
Sundance Multiprocessor Technology Ltd.
The FMC432 is a dual 10 Gigabit Ethernet (10GBASE-T) FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC432 is compatible with FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC432, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card.
-
Product
EMC- EMI test Equipments
-
Our AFJ FFT 3100 & 3300 EMI Receivers cover the full frequency range from 9kHz to 3GHz.To allow a greater flexibility GTemCell can provide either a single or multiple solution of receivers to cover the most common standards and regulations such as CISPR, EN, IEC, FCC etc.
-
Product
Vertical Hinged Mounting Frame, iCon, 5U, 4 Positions
310113508
-
The 5U Vertical hinged Mounting Frame mounts to standard 19" racks and hinges open to allow access to wiring between the instruments and VPC Receiver. The 4 cutouts are spaced evenly across the panel. iCon cover plate sold separately (310113467).
-
Product
Xineos Large Area Detectors
-
As a leader in CMOS innovation, Teledyne DALSA developed the Xineos to deliver three times more sensitivity and five times more signal-to-noise performance than other standard technologies at equal X-ray dose conditions. CMOS image detectors offer numerous advantages including the ability to record smaller image details with higher resolutions – allowing for the diagnostics of medical anomalies at earlier stages, and significantly increasing the probability of early intervention, patient recovery, and reduced treatment costs.
-
Product
Keysight 4-Channel D/A Converter with Waveform Memory for 34980A
34951A
-
The Keysight 34951A module for the 34980A Multifunction Switch/Measure Unit has four electronically calibrated analog channels that can output up to +/-16V DC or +/-20mA DC with 16 bits of resolution. Each channel can be updated individually with a 200 kHz update rate. You can use the standard waveforms provided or create your own with over 500,000 points. These points can be dynamically allocated among one or more channels and output as a point-to-point arb.
-
Product
Polyurethane Jacket RF Cable Assemblies
-
For applications where space is limited and minimizing transferred mechanical stress on the interface connection is a must...The polyurethane jacketed versions of our already proven cable assemblies deliver new engineering options to standard FEP jacketed cables.Polyurethane offers greater memory retention than a similar size cable jacketed with FEP. This feature offers the benefit of minimizing stress and torque applied to interface connections, such as those on a circuit board.It also allows cable to better maintain position in an installation where the "spring back" of an FEP jacketed cable could be problematic.Additionally, a polyurethane jacket offers improved abrasion resistance over an FEP jacket.
-
Product
Saluki S1132 Multi-Standard Signal Generator (9kHz to 6GHz)
-
S1132 series RF signal generator provides a wide range of product choices for different functional requirements and application scenarios, suitable for teaching, research, product development, production, and maintenance. S1132 series features a variety of key analog modulation functions, standard digital modulation functions, and customizable dedicated modulation methods.
-
Product
Standard 2.00 (57.00) - 3.60 (102.00) General Purpose Probe
P2664G-1W1S
-
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 10Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 114Full Travel (mm): 2.90Recommended Travel (mil): 84Recommended Travel (mm): 2.13Overall Length (mil): 895Overall Length (mm): 22.73Overall Length Remark: Tip 1C: 845 mil (21.46 mm) Tip 2R: 935 mil (23.75 mm)
-
Product
DSP Module
CPCI-QIPC-6U
-
The CPCI-4pack-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4pack-6U is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSPvia the CPCI bus or the local serial port.
-
Product
8 Slot, 3U, PXI Chassis - 3 Speed Fan Option
40-908-101
-
This PXI chassis includes all the features and performance required by version 2.1 of the PXI standard and supports a control interface or embedded controller and up to seven more 3U peripheral modules. Mechanical expansion space on the right hand side allows the chassis to accept multi-slot modules, such as the BRIC, while only occupying one electrical slot.
-
Product
Fetal & Neonatal Test Equipment
-
Setting a new performance standard in Fetal/Maternal simulationTwo direct Fetal ECG'sFive full Maternal ECG leadsFour separate Fetal ECG tracingsThree Fetal ultrasound channels with "Triplets" capabilityThirteen Fetal static ECG ratesFifteen trends of Fetal data representing real-life case studies
-
Product
Solvent Resistance Tester
NRJ-100
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;
-
Product
500 Watt DC/DC Converter, 3U VPX
VPX55H-3
-
The VPX55H-3 is NAI's latest high power 500 Watt DC/DC converter that accepts a +28 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 0.8” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Telecom/NEBS Testing
-
Eurofins E&E North America’s extensive capabilities in telecommunications include testing, compliance assistance & design reviews, application preparation and agency liaison. Eurofins tests products for compliance to U.S., Canadian, and international standards for telecom devices, from NEBS equipment to consumer products such as DSL modems.
-
Product
Laser Vibrometer
-
Trialon’s state of the art laser vibrometer can produce vibration testing data without monitoring equipment attached to the test component. This application is used in sensitive situations where the use of more standard accelerometers cannot be used.
-
Product
Touch Screen Controller
EZT-430i/570S
-
The EZT-430i/570S Touch Screen Controller provides users a choice to operate the controller like a smartphone or using window-based navigation. The controller comes standard with data logging, data file access via memory stick or PC, Ethernet control and monitoring, alarm notification via email or phone text message, data file backup, full system security, and may be configured in 28 different languages.
-
Product
Calibrated Leak Standards
-
LeakMaster is a leader in the industry when it comes to the manufacturing of calibrated leak standards (calibrated leak orifices). Each leak standard is meticulously manufactured to a specific leak or flow rate at a predetermined pressure. The purpose of each leak standard is to teach, or calibrate a leak test program, and allow the leak test instrument to memorize the characteristics of a leaking part. These leaks are also introduced into production parts to simulate a “leaking or failed” part condition. LeakMaster supplies a calibrated leak standard with every leak test instrument, and provides recertification services for all of their leak standards
-
Product
16-Channel ADC Module
FMC116
-
Sundance Multiprocessor Technology Ltd.
The FMC116 is a sixteen-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides sixteen A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC116 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
