Electricity
Columbs or amperes.
-
Product
Electrical DfT & Fault Coverage Analyzer
TestWay
-
TestWay's electrical DfT analyzer enables designers to validate designs at the schematic capture stage, to ensure that adequate measures have been included to comply with the manufacturers test requirements. The ability to verify that PCB designs have been developed with adequate Design-for-Test in mind, is key in determining the most effective test strategies and accurately calculating fault coverage, which is crucial in improving competitive advantage, lowering cost and ensuring product quality.
-
Product
LED Thermal and Electrical Performance Analyzer
T5
-
Thermal parameter is the key index to evaluate the performance of LED. It’s very important to measure thermal characteristics of high power LED for high reliability LED applications. It will have effect on the optical parameters, electricity parameters and lifetime of LED. Therefore, design and control of the thermal dissipation is the most important thing for the manufacturers and users.
-
Product
Complete Systems
Universal Testing Device
-
The universal testing device is intended for a diverse range of measurement and automation tasks in laboratories and in test engineering. Thermocouples, RTDs and other sensors can be directly connected. Electrical AC/DC values can also be acquired with the universal testing device.
-
Product
RF Connector
-
Electrical connector designed to work at radio frequencies in the multi-megahertz range. RF connectors are typically used with coaxial cables and are designed to maintain the shielding that the coaxial design offers.
-
Product
Electrical Property Measurement
-
Materials Analysis Technology Inc.
This technology is used to identify the electrical characteristics, such as resistance, capacitance and inductance, of semiconductor devices. Characteristics measured from fail and normal chips could provide important clues for further failure analysis.
-
Product
Electrical Calibration
-
Process Instruments calibrates a wide variety of test and measurement equipment. All calibration procedures are written, and most are automated, insuring reliability and repeatability of measurements.
-
Product
Electric Testing
-
Our Capabilities*Dielectric Withstand*Hi-Potential Testing*Voltage Drop*Contact Resistance*Gate Leakage*Insulation Integrity*Dielectric Integrity
-
Product
Coax, Contact, ITA, 75 Ohm, RG179
610103169
Coax Contact
Primary mating contact 610104157. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield - 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact is 5 milliohms Outer Contact is 3 milliohmsCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
Product
Programmable Multi Output DC Power Supply
LQ6324P
-
- Multi Output Linear DC Power Supply- Digitally Controlled Output Settings- Store / Load 10 Sets of Output Settings in Internal Memory- USB Interface Provided- Programmable Arbitrary Variable Output by Feeding Coefficient of the Curve- User Friendly Front End- Low Cost General Purpose Laboratory Bench Unit- Fully Protected against Overload and Short Circuit- 5V/5A with Over Voltage Crowbar Protection for Digital ICs- Three Independent Outputs Electrically isolated from Each Other- Electrically Floating Outputs up to 500V DC w.r.t. Ground- Precise Regulation, Low Ripple and Noise for Both Constant Voltage & Current Operation
-
Product
Electric Safety
PV-ISOTEST
-
PV-ISOTEST represents a real innovation in the panorama of PV verification and testing instrumentation. PV-ISOTEST measures the insulation resistance of a single module, a string or even an entire photovoltaic field up to 1,500 V DC according to IEC/EN62446 standard.
-
-
Product
Multi Output Regulated DC Power Supply
LQ6324T
-
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
Product
Mini Coax, Contact, ITA, RG316 Double Shield
610103152
Coax Contact
Mini Coax, Contact, ITA, RG316 Double Shield.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
Product
Salt Spray Chambers
-
Weice Testing Instrument Co.,Ltd.
The WTS series of salt spray chambers are manufactured and designed to meet the high quality requirements and standards, such as ISO, JIS, DIN, ASTM, IEC, GB and SAE. They are used to test the resistance capabilities of materials eroded by brine, these materials may be used in Electrical Appliances, Electrical Wire, Accessories, Luminaires etc.
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
Product
Electrical Standards
-
To verify the performance of an electrical calibrator or dc calibrator, you need an electrical standard. Fluke Calibration standards are found in primary calibration laboratories across the world. A wide range of electrical standards and frequency standards are designed to meet the needs of today’s laboratories for traceability and quality accreditation while also being portable, simple to use, and easy to support. Electrical standards include: Voltage standards; ac/dc transfer standards; ac measurement standards; resistance standards; ratio standards; current shunts.
-
Product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/ cd
M8091BSCA
-
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
Product
Automated Titration Analysis Systems
-
MANTECH is a leading manufacturer of multi-parameter and titration analysis systems. We can deliver custom analysis systems that perform the following functions: pH, Chloride, Oxygen, Turbidity, Alkalinity, Fluoride, Oxidation-Reduction Potential (ORP), Nitrate, Electrical Conductivity, Color, Salinity, Total Hardness, Acidity, Ammonia, Temperature and Soil pH & Conductivity.
-
Product
Vertical EFS
-
Teledyne DGO provides a qualified, highly reliable wet-mateable Electrical Feedthrough System for transmitting electrical signal and power from downhole instrumentation through the wellhead. The system incorporates DGO's glass to metal sealing technology in four critical pressure barriers for maximum long term reliability. It establishes a wet-mateable connection between the tubing hanger and running tool, enabling continuous monitoring of instrumentation during run in and initial production.
-
Product
Electric Testers
-
ATEQ offers a broad range of electric testers designed to meet the diverse needs of various industries. These testers, including advanced battery testers, are pivotal in ensuring the efficiency and safety of electrical systems. They are used in applications ranging from automotive and e-mobility to broader industrial purposes and EV battery testing. ATEQ’s electric testers are known for their precision, featuring integrated databases for battery types and parameters, secure systems with comprehensive battery protections, and user-friendly interfaces. This makes them essential tools in production lines, research and development laboratories, and for EV/HEV expertise
-
Product
Portable Electricity Meter Testers
EE-120A-1S
-
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
Product
Hybrid & Electric Vehicle Dynamometer Testing
-
SAKOR Technologies Hybrid/Electric Vehicle Powertrain Dynamometer Test System (HEViDyne), winner of the SAE 2008 Technical Award for Hybrid/Electric Vehicle Testing Technology, is a comprehensive solution for performance, efficiency, and durability testing of all types of hybrid and electric vehicle drivetrains, including:*Hybrid assist (parallel hybrid)*Gasoline or diesel/electric (serial hybrid)*Fully electric vehicles
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
Product
Electricity Metering Device
Mk10A
-
The Mk10A is another addition to the Atlas series which enhances the Mk10 meter with additional communications capabilities for use in Power Quality indication, advanced commissioning functionalities and larger memory storage.
-
Product
30/50 GHz Quad Electrical Channel DCA-M
N1094B
Oscilloscope
The N1094 DCA-M builds on that legacy by using the high-performance elements of 86100 and electrical channel hardware of N104X plug-in modules. Electrical channels are available with 30 GHz and 50 GHz bandwidths.
-
Product
Transceivers
-
Amphenol Fiber Systems International
*300Gb/s Optical Module*225 Electrical Connector*Customizable Duplex to 24 Channel MT Optical Cables*Solves Faceplate Density and I/O Challenges*Faceplate adapters
-
Product
Octal Small Form Factor Pluggable Electrical Interface
-
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
Product
Electrical Testers
-
UEi Test & Measurement Instruments
Devices designed to test the presence of, rather than measure, electrical conditions.
-
Product
Single Position Automated Electric Fluxer
-
Single-position fully automated electric fusion machine with a typical sample throughput of 5-7 samples per hour. Ideal for preparing fused beads for XRF analysis and solutions for AA, ICP, and wet chemistry analysis. Patent PendingTypical samples include: Cement, Clinker, Ores, Slag, Refractories, Ceramics, Catalysts, Glass, Rocks, Minerals, Soils
-
Product
New Design 3m Electric Integrating Sphere
IS-3.0MA
-
It has all functions of IS-*MA Integrating Sphere with Holder Base.• Lisun engineers add the infrared anti-pinch device (the video please come to the “video” tab) and the cross laser positioning device in the integrating sphere.• Please refer to article The New Design 3m Electric Integrating Sphere for more information.
