-
Product
Long-Stroke Tensile Testing System For Vulcanized Rubber
-
Capable of Measuring Even Specimens with a Large Break Strain A tensile test method for vulcanized rubber is stipulated in JIS K6251 (Rubber,vulcanized or thermoplastic-Determination of tensile stress-strain properties). One of the properties of vulcanized rubber is significant elongation. This long-stroke tensile testing system for vulcanized rubber has a long stroke that is required for calculating these tensile characteristics of rubber, and accommodates dumbbell specimens Nos.1 through 6 stipulated in JIS K6251.
-
Product
Miniature Axial Extensometers
Model 3442
-
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the gauge length to be set accurately and repeatably to ASTM and ISO requirements for all gauge lengths. Reengineered quick attach wire forms provide simple and secure specimen attachment. Wire forms for round and flat specimens are included, as well as flat, 3-point, and vee knife edges. The wire forms may be removed to enable mounting using elastic bands or springs. A tethering attachment point provides fall protection and enables counterbalancing of the extensometer’s weight when testing delicate specimens.Model 3442 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller and Epsilon will equip the extensometer with a compatible connector wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of solutions for signal conditioning and connection to data acquisition systems, chart recorders, or other equipment.
-
Product
Fabric Pneumatic Bursting Tester
TF142C
-
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
Product
Vibration Testing
-
Vibration testing includes kinetic energy transfer to the test specimen, often described as the Device Under Test or simply DUT. Typically specified in terms of displacement, velocity, acceleration or the corresponding power spectral density units as a function of frequency. The form of the vibration may be sinusoidal, random, or a combination.
-
Product
One-Touch, Strain Gauge Extensometers
SSG-H Series
-
The SSG-H series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards for hard plastics and metal materials Featuring a wide elongation measurement range with the ability to measure using small gauge lengths, these lightweight, clip-on strain gauge extensometers attach to both rod and flat plate specimens.
-
Product
DIN Scratching Tool
1538
-
The Elcometer 1538 DIN Scratching Tool has interchangeable carbide cutters for the preparation of specimens to be used for corrosion testing.
-
Product
Low Temperature Chamber
-
The Ultra Low Temperature Test Chamber from Weiber are specially designed equipments that provide specific low temperature environments for testing a wide variety of products and their performance under non-ambient testing conditions. They are engineered and configured to meet the exacting low temperature requirements of various research applications and often find their use for evaluation of material properties at extreme temperatures. These versatile test chambers offer the capabilities of measuring temperature extremes, allowing both freeze tolerance studies as well as the effect of heat stress on the sample specimen within the same equipment. They combine advanced technological features with an energy efficient design for highly accurate test conditions and repeatability of results. These test chambers provide a cost-effective solution to expensive laboratory tests and are available at economical prices for increased affordability. They are designed for safe and reliable operation and find widespread usage in chemical and pharmaceutical industries, biotechnology and medicine industry, petroleum industry, food industries and other industrial and manufacturing units.
-
Product
Hot Wire Ignition Tester
-
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
Product
Masks Synthetic Blood Penetration Tester
-
Sataton Instruments Technology CO., Ltd
Medical face masks synthetic blood penetration resistance tester is to evaluate the penetration – splash resistance property of medical face masks by the impact of a small fixed volume of a high-velocity stream of synthetic blood which is projected horizontally. The pneumatically controlled valve will simulate the splatter of blood or other body fluid to disburse at the specimen mask. The tester is suitable to determine the synthetic blood penetration of materials or certain materials used in medical face masks.
-
Product
Dynamic Jack System
-
This is a structural fatigue testing machine for researching the dynamic behavior of full-size or model structures by applying repeated loads. The actuator that supplies the loads to the specimens can be installed on load frames, reaction floors, reaction walls, etc.
-
Product
Pneumatic Capstan Grips For Yarn And Cables
-
These pneumatic grips are used for tensile testing yarn and metal cables and hold specimens using a capstan design. Initial tension can be applied to the specimen to aid sample mounting and alignment and the pneumatic action enables quick and easy specimen insertion.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
Multiphoton Laser Scanning Microscope
FVMPE-RS
-
The Olympus FVMPE-RS multiphoton imaging system is purpose-built for deep imaging in biological tissue, aimed at revealing both detail and dynamics. Innovative features for efficient delivery and detection of photons in scattering media enable high signal-to-noise ratio acquisition. This translates to bright images with precise details — even from deep within the specimen. High sensitivity is matched with high-speed imaging to capture rapid in vivo responses. For advanced applications, dual-wavelength excitation extending to 1300 nm is available. Independent control of visible or multiphoton laser light stimulation and the ability to synchronize with patch clamp data are also possible.
-
Product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
-
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
Product
Hydraulic Flat Grips
-
These 1 kN pneumatic flat grips are designed for tensile testing metal foils. Unique grip features include a very rigid structure, which reduces swivel of the grip faces during testing, and specially shaped flat grip faces. As with all pneumatic grips, these grips allow quick specimen clamping with a repeatable clamping force.
-
Product
Bi-axial Dynacell Load Cells
2527 Series
-
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS AUTOMATIC
-
Optik Elektronik Gerätetechnik GmbH
Automatic measuring instrument for contact angle and free surface energy with motorized pump, automatic drop placement and motorized specimen table (200 x 200) mm.
-
Product
Single Space Electro-hydraulic Servo Universal Testing Machine
WAW-F Series
-
Jinan Testing Equipment IE Corporation
WAW-F series single space Servo-Hydraulic Testing System Computerized is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The ultra-large testing space & dual-action actuator with longer stroke enable it to test not only standard specimen, but also longer ones with long elongation every so often. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing System Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Tester of Single Space is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
Environmental Test Chambers
ET-Series
-
Environmental Test Chambers are designed with uncompromised features included in the system to meet your changing application needs of simulation of wide range of temperature, relative humidity etc., conditions without the added cost of expensive add-on’s as options. Available in varied volumes to fit your differing specimen sizes
-
Product
Washability & Abrasion
-
Improved mechanical resistance to wear is a key requirement of a wide range of products. From coatings to clothing, leather to upholstery, keypads to plastic toys, a product’s ability to resist wear is an important characteristic. There are testing methods relating to the ‘abrasion by friction’ concept. Others are based on the projection of abrasive particles on to the test specimen. These techniques provide valuable information about materials and processes.
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
Product
1 N Clip Grips
-
These very low force 1 N (0.22 lbf) clip grips are for tensile testing fibers, tapes, and other similar shaped specimens. They are designed for use with 50 N (11 lbf) and below load cells.
-
Product
Rubber Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
This machine is used to do the test of wear-resistant in surface, leather, cloth, paint, paper, flooring, plywood, glass and natural rubber. The method is using the standard knife cutting the specimen, and then using the regulated models of grinding wheel with loading weight to be abrased. Remove the specimen after rotation to reach a centain number, and then observe the condition of the specimen or compare the weight with the previous materials.
-
Product
Pneumatic Flat Grips
-
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
Product
Electronic Loads/Sinks
-
An electronic load offers the possibility of testing the specimen under different loads. Various load changes are simulated, as they can occur in normal operation. For this purpose, the relevant load current is set in a defined range and electronically controlled. For the test, different operating states are either programmed or entered into the system via an interface (USB, RS-232, GPIB...). For easy handling and quick use, there are four operating modes.
-
Product
Acoustic Noise
-
American Environments Co., Inc.
A Test Specimens can be evaluated in two different modes in reference to acoustic noise: The Test Specimen's response to acoustic noise and the Test Specimen's generation of acoustic noise.
-
Product
2- and 4-Mirror Floating Zone Crystal Furnaces
IR Image Furnace
-
The high-performance, compact IR Image Furnace from Quantum Design offers unsurpassed performance in a convenient, stand-alone design. Rivaling much larger and more costly IR furnaces, it uses the Floating Zone (FZ) method to promote single crystal growth from a polycrystalline rod. This method has been shown to be extremely effective for a wide class of materials. Now, more easily than ever before, you have the ability to synthesize superior quality single crystal specimens in your own laboratory. This furnace is available in both 2- and 4-mirror versions.
-
Product
Plug-in Temperature Conditioners
PITC
-
The PITC, with a temperature range of -70 C to +177 C, was first introduced in the late 1950s by Bemcos Conrad/Missimer Division. Today, the modernized version of this system is the ideal solution where short run or infrequent tests are required, test specimens are unusual in size or shape, initial capital costs must be held low, or test needs are frequently changed.
-
Product
Needle Microprobe
MT-26/2HT
-
Fast-response 26 gauge needle probe, (needle length is 2 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
